Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Cai Huoqing <cai.huoqing@linux.dev>
To:     kuba@kernel.org
Cc:     Cai Huoqing <cai.huoqing@linux.dev>,
        "David S. Miller" <davem@davemloft.net>,
        Eric Dumazet <edumazet@google.com>,
        Paolo Abeni <pabeni@redhat.com>,
        Zhengchao Shao <shaozhengchao@huawei.com>,
        Jani Nikula <jani.nikula@intel.com>,
        SeongJae Park <sj@kernel.org>,
        Bin Chen <bin.chen@corigine.com>, netdev@vger.kernel.org,
        linux-kernel@vger.kernel.org
Subject: [PATCH net-next v2 2/2] net: hinic: Add control command support for VF PMD driver in DPDK
Date:   Tue,  1 Nov 2022 14:03:39 +0800
Message-Id: <20221101060358.7837-2-cai.huoqing@linux.dev>
In-Reply-To: <20221101060358.7837-1-cai.huoqing@linux.dev>
References: <20221101060358.7837-1-cai.huoqing@linux.dev>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

HINIC has a mailbox for PF-VF communication and the VF driver
could send port control command to PF driver via mailbox.

The control command only can be set to register in PF,
so add support in PF driver for VF PMD driver control
command when VF PMD driver work with linux PF driver.

Then there is no need to add handlers to nic_vf_cmd_msg_handler[],
because the host driver just forwards it to the firmware.
Actually the firmware works on a coprocessor MGMT_CPU(inside the NIC)
which will recv and deal with these commands.

Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
---
v1->v2:
	1.Update the commit messsage.
	2.Add net-next prefix.
	The comments link: https://lore.kernel.org/lkml/20221031195805.74e22089@kernel.org/

 .../net/ethernet/huawei/hinic/hinic_hw_dev.h  | 64 +++++++++++++++++++
 .../net/ethernet/huawei/hinic/hinic_sriov.c   | 18 ++++++
 2 files changed, 82 insertions(+)

diff --git a/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h b/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h
index abffd967a791..4f561e4e849a 100644
--- a/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h
+++ b/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h
@@ -53,11 +53,15 @@ enum hinic_port_cmd {
 
 	HINIC_PORT_CMD_SET_PFC = 0x5,
 
+	HINIC_PORT_CMD_SET_ETS = 0x7,
+	HINIC_PORT_CMD_GET_ETS = 0x8,
+
 	HINIC_PORT_CMD_SET_MAC = 0x9,
 	HINIC_PORT_CMD_GET_MAC = 0xA,
 	HINIC_PORT_CMD_DEL_MAC = 0xB,
 
 	HINIC_PORT_CMD_SET_RX_MODE = 0xC,
+	HINIC_PORT_CMD_SET_ANTI_ATTACK_RATE = 0xD,
 
 	HINIC_PORT_CMD_GET_PAUSE_INFO = 0x14,
 	HINIC_PORT_CMD_SET_PAUSE_INFO = 0x15,
@@ -81,6 +85,7 @@ enum hinic_port_cmd {
 	HINIC_PORT_CMD_GET_RSS_TEMPLATE_INDIR_TBL = 0x25,
 
 	HINIC_PORT_CMD_SET_PORT_STATE = 0x29,
+	HINIC_PORT_CMD_GET_PORT_STATE = 0x30,
 
 	HINIC_PORT_CMD_SET_RSS_TEMPLATE_TBL = 0x2B,
 	HINIC_PORT_CMD_GET_RSS_TEMPLATE_TBL = 0x2C,
@@ -97,17 +102,29 @@ enum hinic_port_cmd {
 
 	HINIC_PORT_CMD_RSS_CFG = 0x42,
 
+	HINIC_PORT_CMD_GET_PHY_TYPE = 0x44,
+
 	HINIC_PORT_CMD_FWCTXT_INIT = 0x45,
 
 	HINIC_PORT_CMD_GET_LOOPBACK_MODE = 0x48,
 	HINIC_PORT_CMD_SET_LOOPBACK_MODE = 0x49,
 
+	HINIC_PORT_CMD_GET_JUMBO_FRAME_SIZE = 0x4A,
+	HINIC_PORT_CMD_SET_JUMBO_FRAME_SIZE = 0x4B,
+
 	HINIC_PORT_CMD_ENABLE_SPOOFCHK = 0x4E,
 
 	HINIC_PORT_CMD_GET_MGMT_VERSION = 0x58,
 
+	HINIC_PORT_CMD_GET_PORT_TYPE = 0x5B,
+
 	HINIC_PORT_CMD_SET_FUNC_STATE = 0x5D,
 
+	HINIC_PORT_CMD_GET_PORT_ID_BY_FUNC_ID = 0x5E,
+
+	HINIC_PORT_CMD_GET_DMA_CS = 0x64,
+	HINIC_PORT_CMD_SET_DMA_CS = 0x65,
+
 	HINIC_PORT_CMD_GET_GLOBAL_QPN = 0x66,
 
 	HINIC_PORT_CMD_SET_VF_RATE = 0x69,
@@ -121,25 +138,72 @@ enum hinic_port_cmd {
 
 	HINIC_PORT_CMD_SET_RQ_IQ_MAP = 0x73,
 
+	HINIC_PORT_CMD_SET_PFC_THD = 0x75,
+
 	HINIC_PORT_CMD_LINK_STATUS_REPORT = 0xA0,
 
+	HINIC_PORT_CMD_SET_LOSSLESS_ETH	= 0xA3,
+
 	HINIC_PORT_CMD_UPDATE_MAC = 0xA4,
 
 	HINIC_PORT_CMD_GET_CAP = 0xAA,
 
+	HINIC_PORT_CMD_UP_TC_ADD_FLOW = 0xAF,
+	HINIC_PORT_CMD_UP_TC_DEL_FLOW = 0xB0,
+	HINIC_PORT_CMD_UP_TC_GET_FLOW = 0xB1,
+
+	HINIC_PORT_CMD_UP_TC_FLUSH_TCAM = 0xB2,
+
+	HINIC_PORT_CMD_UP_TC_CTRL_TCAM_BLOCK = 0xB3,
+
+	HINIC_PORT_CMD_UP_TC_ENABLE = 0xB4,
+
+	HINIC_PORT_CMD_UP_TC_GET_TCAM_BLOCK = 0xB5,
+
+	HINIC_PORT_CMD_SET_IPSU_MAC = 0xCB,
+	HINIC_PORT_CMD_GET_IPSU_MAC = 0xCC,
+
+	HINIC_PORT_CMD_SET_XSFP_STATUS = 0xD4,
 	HINIC_PORT_CMD_GET_LINK_MODE = 0xD9,
 
 	HINIC_PORT_CMD_SET_SPEED = 0xDA,
 
 	HINIC_PORT_CMD_SET_AUTONEG = 0xDB,
 
+	HINIC_PORT_CMD_CLEAR_QP_RES = 0xDD,
+
+	HINIC_PORT_CMD_SET_SUPER_CQE = 0xDE,
+
+	HINIC_PORT_CMD_SET_VF_COS = 0xDF,
+	HINIC_PORT_CMD_GET_VF_COS = 0xE1,
+
+	HINIC_PORT_CMD_CABLE_PLUG_EVENT	= 0xE5,
+
+	HINIC_PORT_CMD_LINK_ERR_EVENT = 0xE6,
+
+	HINIC_PORT_CMD_SET_COS_UP_MAP = 0xE8,
+
+	HINIC_PORT_CMD_RESET_LINK_CFG = 0xEB,
+
 	HINIC_PORT_CMD_GET_STD_SFP_INFO = 0xF0,
 
+	HINIC_PORT_CMD_FORCE_PKT_DROP = 0xF3,
+
 	HINIC_PORT_CMD_SET_LRO_TIMER = 0xF4,
 
+	HINIC_PORT_CMD_SET_VHD_CFG = 0xF7,
+
+	HINIC_PORT_CMD_SET_LINK_FOLLOW = 0xF8,
+
 	HINIC_PORT_CMD_SET_VF_MAX_MIN_RATE = 0xF9,
 
 	HINIC_PORT_CMD_GET_SFP_ABS = 0xFB,
+
+	HINIC_PORT_CMD_Q_FILTER	= 0xFC,
+
+	HINIC_PORT_CMD_TCAM_FILTER = 0xFE,
+
+	HINIC_PORT_CMD_SET_VLAN_FILTER = 0xFF
 };
 
 /* cmd of mgmt CPU message for HILINK module */
diff --git a/drivers/net/ethernet/huawei/hinic/hinic_sriov.c b/drivers/net/ethernet/huawei/hinic/hinic_sriov.c
index a5f08b969e3f..bba41994dee6 100644
--- a/drivers/net/ethernet/huawei/hinic/hinic_sriov.c
+++ b/drivers/net/ethernet/huawei/hinic/hinic_sriov.c
@@ -489,6 +489,24 @@ static struct vf_cmd_check_handle nic_cmd_support_vf[] = {
 	{HINIC_PORT_CMD_UPDATE_MAC, hinic_mbox_check_func_id_8B},
 	{HINIC_PORT_CMD_GET_CAP, hinic_mbox_check_func_id_8B},
 	{HINIC_PORT_CMD_GET_LINK_MODE, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_GET_VF_COS, NULL},
+	{HINIC_PORT_CMD_SET_VHD_CFG, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_SET_VLAN_FILTER, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_Q_FILTER, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_TCAM_FILTER, NULL},
+	{HINIC_PORT_CMD_UP_TC_ADD_FLOW, NULL},
+	{HINIC_PORT_CMD_UP_TC_DEL_FLOW, NULL},
+	{HINIC_PORT_CMD_UP_TC_FLUSH_TCAM, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_UP_TC_CTRL_TCAM_BLOCK, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_UP_TC_ENABLE, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_CABLE_PLUG_EVENT, NULL},
+	{HINIC_PORT_CMD_LINK_ERR_EVENT, NULL},
+	{HINIC_PORT_CMD_SET_PORT_STATE, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_SET_ETS, NULL},
+	{HINIC_PORT_CMD_SET_ANTI_ATTACK_RATE, NULL},
+	{HINIC_PORT_CMD_RESET_LINK_CFG, hinic_mbox_check_func_id_8B},
+	{HINIC_PORT_CMD_SET_LINK_FOLLOW, NULL},
+	{HINIC_PORT_CMD_CLEAR_QP_RES, NULL},
 };
 
 #define CHECK_IPSU_15BIT	0X8000
-- 
2.25.1