Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Matt Ranostay <mranostay@ti.com>
To:     <nm@ti.com>, <afd@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>,
        <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
        <s-vadapalli@ti.com>, <r-gunasekaran@ti.com>
CC:     <linux-arm-kernel@lists.infradead.org>,
        <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v7 5/8] arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support
Date:   Tue, 22 Nov 2022 02:16:13 -0800
Message-ID: <20221122101616.770050-6-mranostay@ti.com>
In-Reply-To: <20221122101616.770050-1-mranostay@ti.com>
References: <20221122101616.770050-1-mranostay@ti.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Content-Type: text/plain
Precedence: bulk

From: Aswath Govindraju <a-govindraju@ti.com>

The board uses lane 1 of SERDES for USB. Set the mux
accordingly.

The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that upto 2 protocols can be used at a time. The SERDES is
wired for PCIe, eDP and USB super-speed. It has been
chosen to use PCIe and eDP as default. So restrict
USB0 to high-speed mode.

Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c3a397484c70..c787d46f89de 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -147,6 +147,12 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
 			J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
 		>;
 	};
+
+	main_usbss0_pins_default: main-usbss0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
+		>;
+	};
 };
 
 &wkup_pmx0 {
@@ -318,6 +324,22 @@ serdes0_pcie_link: phy@0 {
 	};
 };
 
+&usb_serdes_mux {
+	idle-states = <1>; /* USB0 to SERDES lane 1 */
+};
+
+&usbss0 {
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	pinctrl-names = "default";
+	ti,vbus-divider;
+	ti,usb2-only;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.38.GIT