Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S943155AbXHMPOt (ORCPT ); Mon, 13 Aug 2007 11:14:49 -0400 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S1030890AbXHMM7F (ORCPT ); Mon, 13 Aug 2007 08:59:05 -0400 Received: from 193-189-87-45.ip.kis.lt ([193.189.87.45]:21324 "EHLO barclay.wilibox.com" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1030790AbXHMM7B (ORCPT ); Mon, 13 Aug 2007 08:59:01 -0400 X-Greylist: delayed 1972 seconds by postgrey-1.27 at vger.kernel.org; Mon, 13 Aug 2007 08:59:00 EDT Subject: Re: Linux 2.6.23-rc3 From: Zilvinas Valinskas Reply-To: zilvinas@wilibox.com To: Linus Torvalds Cc: Linux Kernel Mailing List In-Reply-To: References: Content-Type: text/plain Date: Mon, 13 Aug 2007 15:23:13 +0300 Message-Id: <1187007793.5717.11.camel@zv.wilibox.com> Mime-Version: 1.0 X-Mailer: Evolution 2.10.3 Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 2272 Lines: 74 Hello lkml, Linux kernel v2.6.23-rc3 booted ok and so far everything is fine. I have HP Compaq nx9420 laptop (Dual Core). Just a few things that I found interesting: 1. /sys/devices/system/clocksource/clocksource0/* $ sudo grep . * available_clocksource:hpet hpet acpi_pm jiffies tsc ^^^^^^^^^ listed twice ;) not a big deal but still. current_clocksource:hpet ^^^^ seems selected ;) although in dmesg there are $ dmesg | grep -i hpet $ dmesg | grep -i hpet ACPI: HPET 7FFE59BC, 0038 (r1 HP 309F 1 HP 1) ACPI: HPET id: 0x8086a201 base: 0xfed00000 hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz hpet_resources: 0xfed00000 is busy ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ? strange. Time: hpet clocksource has been installed. 2. ACPI related (?) - one fan is always on, even when system is idling. It never stops ;) $ acpi -bt Battery 1: charged, 98% Thermal 1: ok, 48.0 degrees C Thermal 2: ok, 38.0 degrees C Thermal 3: active[5], 47.0 degrees C Thermal 4: ok, 37.0 degrees C Thermal 5: ok, 32.0 degrees C Thermal 6: ok, 25.0 degrees C In earlier kernel versions it was turned on when needed (mostly during compilation ...) and then when system is cooled enough fan was automatically turned off. 3. the same messages are printed twice (2.6.23-rc2 was fine). Brought up 2 CPUs NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at f8000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: Using configuration type 1 ACPI: EC: Look up EC in DSDT ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62 ^^^^^^^^^^^^^^^^^^^^^^^^ 1st time ACPI: Interpreter enabled ACPI: (supports S0 S3) ACPI: Using IOAPIC for interrupt routing ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62 ^^^^^^^^^^^^^^^^^^^^^^^^ 2nd time ACPI: PCI Root Bridge [C003] (0000:00) Otherwise I am happy with 2.6.23-rc3. Thank y'all ;) Best regards, Zilvinas - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/