Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
Message-ID: <c7979199-3932-00dc-d349-c0aeb96f5c24@linaro.org>
Date:   Wed, 14 Dec 2022 13:51:30 +0100
MIME-Version: 1.0
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:102.0) Gecko/20100101
 Thunderbird/102.5.1
Subject: Re: [PATCH 3/4] arm64: dts: qcom: sa8540p-ride: add qup1_i2c15 and
 qup2_i2c18 nodes
To:     Brian Masney <bmasney@redhat.com>, andersson@kernel.org,
        krzysztof.kozlowski+dt@linaro.org
Cc:     konrad.dybcio@linaro.org, robh+dt@kernel.org,
        johan+linaro@kernel.org, linux-arm-msm@vger.kernel.org,
        devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
        ahalaney@redhat.com, echanude@redhat.com, quic_shazhuss@quicinc.com
References: <20221212182314.1902632-1-bmasney@redhat.com>
 <20221212182314.1902632-4-bmasney@redhat.com>
Content-Language: en-US
From:   Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
In-Reply-To: <20221212182314.1902632-4-bmasney@redhat.com>
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 7bit
Precedence: bulk

On 12/12/2022 19:23, Brian Masney wrote:
> Add the necessary nodes in order to get qup1_i2c15 and qup2_i2c18
> functioning on the automotive board and exposed to userspace.
> 
> This work was derived from various patches that Qualcomm delivered
> to Red Hat in a downstream kernel. This change was validated by using
> i2c-tools 4.3.3 on CentOS Stream 9:
> 
> [root@localhost ~]# i2cdetect -l
> i2c-15  i2c             Geni-I2C                                I2C adapter
> i2c-18  i2c             Geni-I2C                                I2C adapter
> 
> [root@localhost ~]# i2cdetect -a -y 15
> Warning: Can't use SMBus Quick Write command, will skip some addresses
>      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
> 00:
> 10:
> 20:
> 30: -- -- -- -- -- -- -- --
> 40:
> 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
> 60:
> 70:
> 
> Bus 18 has the same output. I validated that we get the same output on
> the downstream kernel.
> 
> Signed-off-by: Brian Masney <bmasney@redhat.com>
> ---
>  arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 46 +++++++++++++++++++++++
>  1 file changed, 46 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> index d70859803fbd..6dc3f3ff8ece 100644
> --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> @@ -17,6 +17,8 @@ / {
>  	compatible = "qcom,sa8540p-ride", "qcom,sa8540p";
>  
>  	aliases {
> +		i2c15 = &qup1_i2c15;
> +		i2c18 = &qup2_i2c18;
>  		serial0 = &qup2_uart17;
>  	};
>  
> @@ -188,10 +190,28 @@ &pcie3a_phy {
>  	status = "okay";
>  };
>  
> +&qup1 {
> +	status = "okay";
> +};
> +
> +&qup1_i2c15 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&qup1_i2c15_default>;
> +
> +	status = "okay";
> +};
> +
>  &qup2 {
>  	status = "okay";
>  };
>  
> +&qup2_i2c18 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&qup2_i2c18_default>;
> +
> +	status = "okay";
> +};
> +
>  &qup2_uart17 {
>  	compatible = "qcom,geni-debug-uart";
>  	status = "okay";
> @@ -313,4 +333,30 @@ wake-pins {
>  			bias-pull-up;
>  		};
>  	};
> +
> +	qup1_i2c15_default: qup1-i2c15-state {
> +		mux-pins {
> +			pins = "gpio36", "gpio37";
> +			function = "qup15";
> +		};
> +
> +		config-pins {
> +			pins = "gpio36", "gpio37";
> +			drive-strength = <0x02>;

Except the problem pointed out by Konrad (we do not have separate mux
and config pins anymore), this is not a hex, it's mA.


Best regards,
Krzysztof