Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
Message-ID: <6061938c-b830-2fe0-2f4d-368e34c33676@linaro.org>
Date:   Thu, 29 Dec 2022 21:05:23 +0000
MIME-Version: 1.0
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:102.0) Gecko/20100101
 Thunderbird/102.4.2
Subject: Re: [PATCH v2 2/2] phy: qcom-usb-hs: Add qcom,dp-manual-pullup logic
Content-Language: en-US
To:     Stephan Gerhold <stephan@gerhold.net>
Cc:     agross@kernel.org, andersson@kernel.org, vkoul@kernel.org,
        kishon@kernel.org, robh+dt@kernel.org,
        krzysztof.kozlowski+dt@linaro.org, konrad.dybcio@linaro.org,
        linux-arm-msm@vger.kernel.org, linux-phy@lists.infradead.org,
        devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
        linux-usb@vger.kernel.org
References: <20221229183410.683584-1-bryan.odonoghue@linaro.org>
 <20221229183410.683584-3-bryan.odonoghue@linaro.org>
 <Y63uSgMdP4m6nvhL@gerhold.net> <Y64AfHcUw192Pyr6@gerhold.net>
From:   Bryan O'Donoghue <bryan.odonoghue@linaro.org>
In-Reply-To: <Y64AfHcUw192Pyr6@gerhold.net>
Content-Type: text/plain; charset=UTF-8; format=flowed
Content-Transfer-Encoding: 7bit
Precedence: bulk

On 29/12/2022 21:02, Stephan Gerhold wrote:
> On Thu, Dec 29, 2022 at 08:45:15PM +0100, Stephan Gerhold wrote:
>> On Thu, Dec 29, 2022 at 06:34:10PM +0000, Bryan O'Donoghue wrote:
>>> Downstream has a flag called qcom,dp-manual-pullup which informs the
>>> downstream driver if it should toggle ULPI_MISC_A_VBUSVLDEXTSEL and
>>> ULPI_MISC_A_VBUSVLDEXT.
>>>
>>> Downstream states:
>>>
>>> "qcom,dp-manual-pullup: If present, vbus is not routed to USB
>>>          controller/phy and controller driver therefore enables pull-up
>>>          explicitly before starting controller using usbcmd run/stop bit."
>>>
>>> Working with a system that has both an external Type-C port controller and
>>> an internal USB Hub results in a situation where VBUS is not connected to
>>> the SoC.
>>>
>>> In this case we still need to set the DP pullup.
>>>
>>> This patch enables and disables the DP pullup on PHY power_on and power_off
>>> respectively if the DT has declared the bool "qcom,enable-vbus-pullup"
>>> effectively replicating the downstream logic to the same effect.
>>>
>>> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
>> [...]
>>
>> An alternative that I've occasionally used for early bring-up is to
>> simply use a dummy extcon driver [1] that permanently reports active
>> VBUS. The end result is the same. While it's clearly a hack perhaps this
>> makes it a bit more clear that ideally you really should try to assign
>> an extcon device, to avoid keeping the USB controller and PHY on
>> permanently.
>>
> 
> BTW another nice trick that should work in all almost all cases is to
> use the state of the PMIC USB_IN pin as VBUS detection. All battery-
> powered devices I have seen route the USB VBUS to PM8916 USB_IN. And
> even many boards like DB410c seem to do that or at least permanently
> supply 5V there. In all these cases the &pm8916_usbin extcon will
> report a VBUS state that should make USB work.
> 
> Have you tried using that on your MSM8939 board with the Type-C setup?
> 
> &pm8916_usbin {
> 	status = "okay";
> };
> 
> &usb {
> 	status = "okay";
> 	usb-role-switch;
> 	extcon = <&pm8916_usbin>;
> };
> 
> &usb_hs_phy {
> 	extcon = <&pm8916_usbin>;
> };
> 
> Stephan

I checked USBIN before my last email reply.

Its possible its connected but its not there on the 8939 schematic I have.

---
bod