Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
Message-ID: <3f0ade86-cab1-1f5a-fd49-326802473b76@linaro.org>
Date:   Wed, 18 Jan 2023 09:27:01 +0100
MIME-Version: 1.0
User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:102.0) Gecko/20100101
 Thunderbird/102.6.0
From:   Neil Armstrong <neil.armstrong@linaro.org>
Reply-To: neil.armstrong@linaro.org
Subject: Re: [PATCH v2 3/9] arm64: dts: amlogic: Used onboard usb hub reset on
 odroid c2
Content-Language: en-US
To:     Anand Moon <linux.amoon@gmail.com>,
        Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Kevin Hilman <khilman@baylibre.com>,
        Jerome Brunet <jbrunet@baylibre.com>,
        Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc:     linux-amlogic@lists.infradead.org,
        Matthias Kaehlcke <mka@chromium.org>,
        Alexander Stein <alexander.stein@ew.tq-group.com>,
        Johan Hovold <johan@kernel.org>, devicetree@vger.kernel.org,
        linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org
References: <20230118044418.875-1-linux.amoon@gmail.com>
 <20230118044418.875-4-linux.amoon@gmail.com>
Organization: Linaro Developer Services
In-Reply-To: <20230118044418.875-4-linux.amoon@gmail.com>
Content-Type: text/plain; charset=UTF-8; format=flowed
Content-Transfer-Encoding: 7bit
Precedence: bulk

On 18/01/2023 05:44, Anand Moon wrote:
> On Odroid c2 previously use gpio-hog to reset the usb hub,
> switch to used on-board usb hub reset to enable the usb hub
> and enable power to hub.
> 
> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> ---
> v2 - drop the vendor name from compatible string.
>     - move the hub node to USB controller node.
>     - drop the usb_otg_pwr since it only liked to OTG port
>           and link p5v0 to the vdd-supply.
> ---
>   .../boot/dts/amlogic/meson-gxbb-odroidc2.dts  | 26 ++++++++-----------
>   1 file changed, 11 insertions(+), 15 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> index 201596247fd9..01356437a077 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> @@ -250,21 +250,6 @@ eth_phy0: ethernet-phy@0 {
>   	};
>   };
>   
> -&gpio_ao {
> -	/*
> -	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
> -	 * to be turned high in order to be detected by the USB Controller
> -	 * This signal should be handled by a USB specific power sequence
> -	 * in order to reset the Hub when USB bus is powered down.
> -	 */
> -	hog-0 {
> -		gpio-hog;
> -		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
> -		output-high;
> -		line-name = "usb-hub-reset";
> -	};
> -};
> -
>   &hdmi_tx {
>   	status = "okay";
>   	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> @@ -414,5 +399,16 @@ &usb0 {
>   };
>   
>   &usb1 {
> +	dr_mode = "host";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
>   	status = "okay";
> +
> +	hub@1 {
> +		/* Genesys Logic GL852G USB 2.0 hub */
> +		compatible = "usb5e3,610";
> +		reg = <1>;
> +		vdd-supply = <&p5v0>;
> +		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
> +	};
>   };

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>