Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Anand Moon <linux.amoon@gmail.com>
To:     Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Neil Armstrong <neil.armstrong@linaro.org>,
        Kevin Hilman <khilman@baylibre.com>,
        Jerome Brunet <jbrunet@baylibre.com>,
        Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc:     linux-amlogic@lists.infradead.org,
        Matthias Kaehlcke <mka@chromium.org>,
        Alexander Stein <alexander.stein@ew.tq-group.com>,
        Johan Hovold <johan@kernel.org>, devicetree@vger.kernel.org,
        linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH v3 7/9] arm64: dts: amlogic: Used onboard usb hub reset on odroid c4
Date:   Sat, 21 Jan 2023 17:56:35 +0000
Message-Id: <20230121175639.12818-8-linux.amoon@gmail.com>
In-Reply-To: <20230121175639.12818-1-linux.amoon@gmail.com>
References: <20230121175639.12818-1-linux.amoon@gmail.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

On Odroid c4 previously use gpio-hog to reset the usb hub,
switch to used on-board usb hub reset to enable the usb hub
and enable power to hub.

USB hub is combination of USB 2.0 and USB 3.0 root hub so
use peer-hub node to link then.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
v3: - move the usb hub under dwc3 node.
      dropped dr_mode
v2: - fix the compatible string.
    - Fix the hub node to use peer-hub to link the usb 2.0 and usb 3.0.
---
 .../boot/dts/amlogic/meson-sm1-odroid-c4.dts  | 33 ++++++++++++-------
 1 file changed, 21 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts
index 8c30ce63686e..a988015dd2d5 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts
@@ -28,18 +28,27 @@ sound {
 	};
 };
 
-&gpio {
-	/*
-	 * WARNING: The USB Hub on the Odroid-C4 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	hog-0 {
-		gpio-hog;
-		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
+&dwc3 {
+	/* USB hub supports both USB 2.0 and USB 3.0 root hub */
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* 2.0 hub on port 1 */
+	hub_2_0: hub@1 {
+		compatible = "usb2109,2817";
+		reg = <1>;
+		peer-hub = <&hub_3_0>;
+		reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&vcc_5v>;
+	};
+
+	/* 3.1 hub on port 4 */
+	hub_3_0: hub@2 {
+		compatible = "usb2109,817";
+		reg = <2>;
+		peer-hub = <&hub_2_0>;
+		reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&vcc_5v>;
 	};
 };
 
-- 
2.38.1