Feedback-ID: i0ad843c9:Fastmail
From:   Samuel Holland <samuel@sholland.org>
To:     Chen-Yu Tsai <wens@csie.org>,
        Jernej Skrabec <jernej.skrabec@gmail.com>,
        linux-sunxi@lists.linux.dev
Cc:     linux-riscv@lists.infradead.org, Heiko Stuebner <heiko@sntech.de>,
        Palmer Dabbelt <palmer@dabbelt.com>,
        Conor Dooley <conor@kernel.org>,
        Jisheng Zhang <jszhang@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
        Andre Przywara <andre.przywara@arm.com>,
        Rob Herring <robh+dt@kernel.org>,
        linux-arm-kernel@lists.infradead.org,
        Samuel Holland <samuel@sholland.org>,
        Palmer Dabbelt <palmer@rivosinc.com>,
        Guo Ren <guoren@kernel.org>,
        Conor Dooley <conor.dooley@microchip.com>
Subject: [PATCH v5 06/11] riscv: dts: allwinner: Add Allwinner D1 Nezha devicetree
Date:   Wed, 25 Jan 2023 22:57:33 -0600
Message-Id: <20230126045738.47903-7-samuel@sholland.org>
In-Reply-To: <20230126045738.47903-1-samuel@sholland.org>
References: <20230126045738.47903-1-samuel@sholland.org>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

"D1 Nezha" is Allwinner's first-party development board for the D1 SoC.
It was shipped with 512M, 1G, or 2G of DDR3. It supports onboard audio,
HDMI, gigabit Ethernet, WiFi and Bluetooth, USB 2.0 host and OTG ports,
plus low-speed I/O from the SoC and a GPIO expander chip.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---

(no changes since v3)

Changes in v3:
 - Drop mmc alias

Changes in v2:
 - Common regulators moved to MangoPi MQ patch, removed analog LDOs
 - Removed LRADC (depends on analog LDOs)
 - Added XR829 host-wake interrupt

 arch/riscv/boot/dts/allwinner/Makefile        |   1 +
 .../boot/dts/allwinner/sun20i-d1-nezha.dts    | 166 ++++++++++++++++++
 2 files changed, 167 insertions(+)
 create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts

diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
index 2f2792594f7d..277e59d1c907 100644
--- a/arch/riscv/boot/dts/allwinner/Makefile
+++ b/arch/riscv/boot/dts/allwinner/Makefile
@@ -1,2 +1,3 @@
 # SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
new file mode 100644
index 000000000000..a0769185be97
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "Allwinner D1 Nezha";
+	compatible = "allwinner,d1-nezha", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &emac;
+		ethernet1 = &xr829;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_usbvbus: usbvbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbvbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
+		enable-active-high;
+		vin-supply = <&reg_vcc>;
+	};
+
+	/*
+	 * This regulator is PWM-controlled, but the PWM controller is not
+	 * yet supported, so fix the regulator to its default voltage.
+	 */
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-0 = <&rgmii_pe_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_vcc_3v3>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pb0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	pcf8574a: gpio@38 {
+		compatible = "nxp,pcf8574a";
+		reg = <0x38>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 2 IRQ_TYPE_LEVEL_LOW>; /* PB2 */
+		interrupt-controller;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	xr829: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* XR829 bluetooth is connected here */
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 3 21 GPIO_ACTIVE_HIGH>; /* PD21 */
+	usb0_vbus_det-gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+	usb0_vbus-supply = <&reg_usbvbus>;
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
-- 
2.37.4