MIME-Version: 1.0
References: <20230120184500.1899814-1-martin.botka@somainline.org> <20230120184500.1899814-4-martin.botka@somainline.org>
In-Reply-To: <20230120184500.1899814-4-martin.botka@somainline.org>
Reply-To: wens@csie.org
From:   Chen-Yu Tsai <wens@csie.org>
Date:   Sat, 28 Jan 2023 01:24:18 +0800
Message-ID: <CAGb2v649yQVcNn7uv1eKtnEDnb=D4X9yGYB1eOC3zeAe+encFg@mail.gmail.com>
Subject: Re: [PATCH v8 3/3] regulator: axp20x: Add support for AXP313a variant
To:     Martin Botka <martin.botka@somainline.org>
Cc:     martin.botka1@gmail.com,
        Konrad Dybcio <konrad.dybcio@somainline.org>,
        AngeloGioacchino Del Regno 
        <angelogioacchino.delregno@somainline.org>,
        Marijn Suijten <marijn.suijten@somainline.org>,
        Jami Kettunen <jamipkettunen@somainline.org>,
        Paul Bouchara <paul.bouchara@somainline.org>,
        Jan Trmal <jtrmal@gmail.com>,
        Jernej Skrabec <jernej.skrabec@gmail.com>,
        Samuel Holland <samuel@sholland.org>,
        Andre Przywara <andre.przywara@arm.com>,
        Lee Jones <lee@kernel.org>, Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Liam Girdwood <lgirdwood@gmail.com>,
        Mark Brown <broonie@kernel.org>, devicetree@vger.kernel.org,
        linux-kernel@vger.kernel.org
Content-Type: text/plain; charset="UTF-8"
Precedence: bulk

On Sat, Jan 21, 2023 at 2:45 AM Martin Botka
<martin.botka@somainline.org> wrote:
>
> The AXP313a is your typical I2C controlled PMIC, although in a lighter
> fashion compared to the other X-Powers PMICs: it has only three DCDC
> rails, three LDOs, and no battery charging support.
>
> The AXP313a datasheet does not describe a register to change the DCDC
> switching frequency, and talks of it being fixed at 3 MHz. The BSP
> driver hints at a register being able to change that, but we haven't
> verified that, so leave that one out. It can be added later, if needed
> and/or required.

The datasheet released by MangoPi says this isn't configurable. The
thing that is configurable is spread-spectrum operation, and mode
switching between fixed PWM and hybrid PFM/PWM. So just drop the
DCDC frequency stuff and use the default code path.

> The third LDO, RTCLDO, is fixed, and cannot even be turned on or off,
> programmatically. On top of that, its voltage is customisable (either
> 1.8V or 3.3V), which we cannot describe easily using the existing
> regulator wrapper functions. This should be fixed properly, using
> regulator-{min,max}-microvolt in the DT, but this requires more changes
> to the code. As some other PMICs (AXP2xx, AXP803) seem to paper over the
> same problem as well, we follow suit here and pretend it's a fixed 1.8V
> regulator. A proper fix can follow later. The BSP code seems to ignore
> this regulator altogether.
>
> Describe the AXP313A's voltage settings and switch registers, how the
> voltages are encoded, and connect this to the MFD device via its
> regulator ID.
>
> Signed-off-by: Martin Botka <martin.botka@somainline.org>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  drivers/regulator/axp20x-regulator.c | 60 ++++++++++++++++++++++++++++
>  1 file changed, 60 insertions(+)
>
> diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
> index d260c442b788..3087bc98694f 100644
> --- a/drivers/regulator/axp20x-regulator.c
> +++ b/drivers/regulator/axp20x-regulator.c
> @@ -134,6 +134,11 @@
>  #define AXP22X_PWR_OUT_DLDO4_MASK      BIT_MASK(6)
>  #define AXP22X_PWR_OUT_ALDO3_MASK      BIT_MASK(7)
>
> +#define AXP313A_DCDC1_NUM_VOLTAGES     107
> +#define AXP313A_DCDC23_NUM_VOLTAGES    88
> +#define AXP313A_DCDC_V_OUT_MASK                GENMASK(6, 0)
> +#define AXP313A_LDO_V_OUT_MASK         GENMASK(4, 0)
> +
>  #define AXP803_PWR_OUT_DCDC1_MASK      BIT_MASK(0)
>  #define AXP803_PWR_OUT_DCDC2_MASK      BIT_MASK(1)
>  #define AXP803_PWR_OUT_DCDC3_MASK      BIT_MASK(2)
> @@ -638,6 +643,48 @@ static const struct regulator_desc axp22x_drivevbus_regulator = {
>         .ops            = &axp20x_ops_sw,
>  };
>
> +static const struct linear_range axp313a_dcdc1_ranges[] = {
> +       REGULATOR_LINEAR_RANGE(500000,   0,  70,  10000),
> +       REGULATOR_LINEAR_RANGE(1220000, 71,  87,  20000),
> +       REGULATOR_LINEAR_RANGE(1600000, 88, 106, 100000),
> +};
> +
> +static const struct linear_range axp313a_dcdc2_ranges[] = {
> +       REGULATOR_LINEAR_RANGE(500000,   0, 70, 10000),
> +       REGULATOR_LINEAR_RANGE(1220000, 71, 87, 20000),
> +};
> +
> +/*
> + * This is deviating from the datasheet. The values here are taken from the
> + * BSP driver and have been confirmed by measurements.
> + */
> +static const struct linear_range axp313a_dcdc3_ranges[] = {
> +       REGULATOR_LINEAR_RANGE(500000,   0,  70, 10000),
> +       REGULATOR_LINEAR_RANGE(1220000, 71, 102, 20000),
> +};
> +
> +static const struct regulator_desc axp313a_regulators[] = {
> +       AXP_DESC_RANGES(AXP313A, DCDC1, "dcdc1", "vin1",
> +                       axp313a_dcdc1_ranges, AXP313A_DCDC1_NUM_VOLTAGES,
> +                       AXP313A_DCDC1_CONRTOL, AXP313A_DCDC_V_OUT_MASK,
> +                       AXP313A_OUTPUT_CONTROL, BIT(0)),
> +       AXP_DESC_RANGES(AXP313A, DCDC2, "dcdc2", "vin2",
> +                       axp313a_dcdc2_ranges, AXP313A_DCDC23_NUM_VOLTAGES,
> +                       AXP313A_DCDC2_CONRTOL, AXP313A_DCDC_V_OUT_MASK,
> +                       AXP313A_OUTPUT_CONTROL, BIT(1)),
> +       AXP_DESC_RANGES(AXP313A, DCDC3, "dcdc3", "vin3",
> +                       axp313a_dcdc3_ranges, AXP313A_DCDC23_NUM_VOLTAGES,
> +                       AXP313A_DCDC3_CONRTOL, AXP313A_DCDC_V_OUT_MASK,
> +                       AXP313A_OUTPUT_CONTROL, BIT(2)),
> +       AXP_DESC(AXP313A, LDO1, "ldo1", "vin1", 500, 3500, 100,
> +                AXP313A_ALDO1_CONRTOL, AXP313A_LDO_V_OUT_MASK,
> +                AXP313A_OUTPUT_CONTROL, BIT(3)),

The datasheet says this one is called ALDO1 ...

> +       AXP_DESC(AXP313A, LDO2, "ldo2", "vin1", 500, 3500, 100,
> +                AXP313A_DLDO1_CONRTOL, AXP313A_LDO_V_OUT_MASK,
> +                AXP313A_OUTPUT_CONTROL, BIT(4)),

... and this one DLDO1.

> +       AXP_DESC_FIXED(AXP313A, RTC_LDO, "rtc-ldo", "vin1", 1800),
> +};
> +
>  /* DCDC ranges shared with AXP813 */
>  static const struct linear_range axp803_dcdc234_ranges[] = {
>         REGULATOR_LINEAR_RANGE(500000,
> @@ -1040,6 +1087,15 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
>                 def = 3000;
>                 step = 150;
>                 break;
> +       case AXP313A_ID:
> +               /* The DCDC PWM frequency seems to be fixed to 3 MHz. */
> +               if (dcdcfreq != 3000000 && dcdcfreq != 0) {
> +                       dev_err(&pdev->dev,
> +                               "DCDC frequency on AXP313a is fixed to 3 MHz.\n");
> +                       return -EINVAL;
> +               }
> +
> +               return 0;

As mentioned above, please drop this.

Besides the bits mentioned above, this looks OK.

>         default:
>                 dev_err(&pdev->dev,
>                         "Setting DCDC frequency for unsupported AXP variant\n");
> @@ -1232,6 +1288,10 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
>                 drivevbus = of_property_read_bool(pdev->dev.parent->of_node,
>                                                   "x-powers,drive-vbus-en");
>                 break;
> +       case AXP313A_ID:
> +               regulators = axp313a_regulators;
> +               nregulators = AXP313A_REG_ID_MAX;
> +               break;
>         case AXP803_ID:
>                 regulators = axp803_regulators;
>                 nregulators = AXP803_REG_ID_MAX;
> --
> 2.39.0
>