Date:   Thu, 9 Feb 2023 16:21:14 +0000
From:   Matthias Kaehlcke <mka@chromium.org>
To:     Bhupesh Sharma <bhupesh.sharma@linaro.org>
Cc:     linux-arm-msm@vger.kernel.org, agross@kernel.org,
        andersson@kernel.org, konrad.dybcio@linaro.org,
        linux-kernel@vger.kernel.org, bhupesh.linux@gmail.com,
        robh+dt@kernel.org, devicetree@vger.kernel.org
Subject: Re: [PATCH v2] arm64: dts: qcom: sm6115: Add geni debug uart node
 for qup0
Message-ID: <Y+UdetQklamQUehi@google.com>
References: <20230208122718.338545-1-bhupesh.sharma@linaro.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=utf-8
Content-Disposition: inline
In-Reply-To: <20230208122718.338545-1-bhupesh.sharma@linaro.org>
Precedence: bulk

On Wed, Feb 08, 2023 at 05:57:18PM +0530, Bhupesh Sharma wrote:
> qup0 on sm6115 / sm4250 has 6 SEs, with SE4 as debug uart.
> Add the debug uart node in sm6115 dtsi file.

Is there anything special about SE4 that makes it *the* debug
UART or does it just happen to be the UART that is used by the
reference board? I suspect the latter, in which case the
"qcom,geni-debug-uart" string should be set/overwritten in the
board file as in sc7280-qcard.dtsi or sc8280xp-crd.dts.

> Cc: Bjorn Andersson <andersson@kernel.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
> ---
>  Changes since v1:
>   - v1 can be viewed here: https://lore.kernel.org/linux-arm-msm/20221128171215.1768745-1-bhupesh.sharma@linaro.org/
>   - Addressed Konrad's review comments on v1.
>   - Rebased againt latest linux-next/master which now has the 'qupv3_id_0' node
>     already in the dtsi file, so just add the debug uart node in v2.
> 
>  arch/arm64/boot/dts/qcom/sm6115.dtsi | 10 +++++++++-
>  1 file changed, 9 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> index 50cb8a82ecd5..3eccfb8c16ce 100644
> --- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> @@ -963,6 +963,15 @@ spi4: spi@4a90000 {
>  				status = "disabled";
>  			};
>  
> +			uart4: serial@4a90000 {
> +				compatible = "qcom,geni-debug-uart";
> +				reg = <0x04a90000 0x4000>;
> +				clock-names = "se";
> +				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
> +				interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
> +				status = "disabled";
> +			};
> +
>  			i2c5: i2c@4a94000 {
>  				compatible = "qcom,geni-i2c";
>  				reg = <0x04a94000 0x4000>;
> @@ -992,7 +1001,6 @@ spi5: spi@4a94000 {
>  				dma-names = "tx", "rx";
>  				#address-cells = <1>;
>  				#size-cells = <0>;
> -				status = "disabled";
>  			};
>  		};
>  
> -- 
> 2.38.1
>