MIME-Version: 1.0
References: <20230214145609.kernel.v1.1.Ibe4d3a42683381c1e78b8c3aa67b53fc74437ae9@changeid>
 <CABBYNZKVVo4T_pbEdozhNvgiykC7NiLQKEnJi3q5gZpHunGrbA@mail.gmail.com>
In-Reply-To: <CABBYNZKVVo4T_pbEdozhNvgiykC7NiLQKEnJi3q5gZpHunGrbA@mail.gmail.com>
From:   Zhengping Jiang <jiangzp@google.com>
Date:   Tue, 14 Feb 2023 16:28:09 -0800
Message-ID: <CAB4PzUo+EuapOr+O7eWZH2xiVVAUd98m_DmEK-337=CvfUDeoA@mail.gmail.com>
Subject: Re: [kernel PATCH v1] Bluetooth: hci_sync: Resume adv with no RPA
 when active scan
To:     Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc:     linux-bluetooth@vger.kernel.org, marcel@holtmann.org,
        chromeos-bluetooth-upstreaming@chromium.org,
        "David S. Miller" <davem@davemloft.net>,
        Eric Dumazet <edumazet@google.com>,
        Jakub Kicinski <kuba@kernel.org>,
        Johan Hedberg <johan.hedberg@gmail.com>,
        Paolo Abeni <pabeni@redhat.com>, linux-kernel@vger.kernel.org,
        netdev@vger.kernel.org
Content-Type: text/plain; charset="UTF-8"
Content-Transfer-Encoding: quoted-printable
Precedence: bulk

Hi Luiz,

Thanks for the comment. I will submit a new patch to address that.

I notice in the spec, it is mentioned
> Note: This command does not affect the generation of Resolvable Private A=
ddresses.
How should I understand this note? Does it mean even if the address
resolution is disabled, the controller can still generate RPA for
advertising?  Does it mean the advertising can always be resumed
during active scan?

Thanks,
Zhengping

On Tue, Feb 14, 2023 at 4:09 PM Luiz Augusto von Dentz
<luiz.dentz@gmail.com> wrote:
>
> Hi Zhengping,
>
> On Tue, Feb 14, 2023 at 2:56 PM Zhengping Jiang <jiangzp@google.com> wrot=
e:
> >
> > The address resolution should be disabled during the active scan,
> > so all the advertisements can reach the host. The advertising
> > has to be paused before disabling the address resolution,
> > because the advertising will prevent any changes to the resolving
> > list and the address resolution status. Skipping this will cause
> > the hci error and the discovery failure.
>
> It is probably a good idea to quote the spec saying:
>
> 7.8.44 LE Set Address Resolution Enable command
>
> This command shall not be used when:
> =E2=80=A2 Advertising (other than periodic advertising) is enabled,
>
> > If the host is using RPA, the controller needs to generate RPA for
> > the advertising, so the advertising must remain paused during the
> > active scan.
> >
> > If the host is not using RPA, the advertising can be resumed after
> > disabling the address resolution.
> >
> > Fixes: 9afc675edeeb ("Bluetooth: hci_sync: allow advertise when scan wi=
thout RPA")
> > Signed-off-by: Zhengping Jiang <jiangzp@google.com>
> > ---
> >
> > Changes in v1:
> > - Always pause advertising when active scan, but resume the advertising=
 if the host is not using RPA
> >
> >  net/bluetooth/hci_sync.c | 8 ++++++--
> >  1 file changed, 6 insertions(+), 2 deletions(-)
> >
> > diff --git a/net/bluetooth/hci_sync.c b/net/bluetooth/hci_sync.c
> > index 117eedb6f709..edbf9faf7fa1 100644
> > --- a/net/bluetooth/hci_sync.c
> > +++ b/net/bluetooth/hci_sync.c
> > @@ -2402,7 +2402,7 @@ static u8 hci_update_accept_list_sync(struct hci_=
dev *hdev)
> >         u8 filter_policy;
> >         int err;
> >
> > -       /* Pause advertising if resolving list can be used as controlle=
rs are
> > +       /* Pause advertising if resolving list can be used as controlle=
rs
> >          * cannot accept resolving list modifications while advertising=
.
> >          */
> >         if (use_ll_privacy(hdev)) {
> > @@ -5397,7 +5397,7 @@ static int hci_active_scan_sync(struct hci_dev *h=
dev, uint16_t interval)
> >         /* Pause advertising since active scanning disables address res=
olution
> >          * which advertising depend on in order to generate its RPAs.
> >          */
> > -       if (use_ll_privacy(hdev) && hci_dev_test_flag(hdev, HCI_PRIVACY=
)) {
> > +       if (use_ll_privacy(hdev)) {
> >                 err =3D hci_pause_advertising_sync(hdev);
> >                 if (err) {
> >                         bt_dev_err(hdev, "pause advertising failed: %d"=
, err);
> > @@ -5416,6 +5416,10 @@ static int hci_active_scan_sync(struct hci_dev *=
hdev, uint16_t interval)
> >                 goto failed;
> >         }
> >
> > +       // Resume paused advertising if the host is not using RPA
> > +       if (use_ll_privacy(hdev) && !hci_dev_test_flag(hdev, HCI_PRIVAC=
Y))
> > +               hci_resume_advertising_sync(hdev);
> > +
> >         /* All active scans will be done with either a resolvable priva=
te
> >          * address (when privacy feature has been enabled) or non-resol=
vable
> >          * private address.
> > --
> > 2.39.1.581.gbfd45094c4-goog
>
> I think it is better that we add something like
> hci_pause_addr_resolution so we can make it check all the conditions,
> such as pausing advertising and resuming if needed. Btw, we do seem to
> have proper checks for these conditions on the emulator:
>
> https://git.kernel.org/pub/scm/bluetooth/bluez.git/tree/emulator/btdev.c#=
n4090
>
> But perhaps there is no test which attempts to enable LL Privacy
> without enabling Local Privacy, so it would be great if you could
> update mgmt-tester adding a test that emulates such behavior.
>
> --
> Luiz Augusto von Dentz