From:   Martin Blumenstingl <martin.blumenstingl@googlemail.com>
To:     linux-amlogic@lists.infradead.org
Cc:     linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org,
        neil.armstrong@linaro.org,
        Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Subject: [PATCH v1 3/3] ARM: dts: meson8m2: mxiii-plus: Enable Bluetooth and WiFi support
Date:   Tue, 21 Mar 2023 18:12:13 +0100
Message-Id: <20230321171213.2808460-4-martin.blumenstingl@googlemail.com>
In-Reply-To: <20230321171213.2808460-1-martin.blumenstingl@googlemail.com>
References: <20230321171213.2808460-1-martin.blumenstingl@googlemail.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

The MXIII Plus uses an Ampak AP6330 Bluetooth and WiFi combo chip.
Bluetooth is connected to &uart_A and requires toggling GPIOX_20.
WiFi can be routed to either &sdhc or &sdio. Route WiFi to &sdhc
since  &sdio is already connected to the SD card. Additionally WiFi
requires toggling GPIOX_11 and GPIOAO_6 as well as enabling the 32kHz
clock signal.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 arch/arm/boot/dts/meson8m2-mxiii-plus.dts | 48 ++++++++++++++++++++++-
 1 file changed, 47 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
index fa6d55f1cfb9..aa4d4bf70629 100644
--- a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
+++ b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
@@ -19,7 +19,6 @@ aliases {
 		ethernet0 = &ethmac;
 		i2c0 = &i2c_AO;
 		serial0 = &uart_AO;
-		serial1 = &uart_A;
 		mmc0 = &sd_card_slot;
 	};
 
@@ -45,12 +44,32 @@ button-function {
 		};
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		pinctrl-0 = <&xtal_32k_out_pins>;
+		pinctrl-names = "default";
+
+		reset-gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>,
+			      <&gpio_ao GPIOAO_6 GPIO_ACTIVE_LOW>;
+
+		clocks = <&xtal_32k_out>;
+		clock-names = "ext_clock";
+	};
+
 	vcc_3v3: regulator-vcc3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "VCC3V3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	xtal_32k_out: xtal-32k-out-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xtal_32k_out";
+	};
 };
 
 &cpu0 {
@@ -192,6 +211,27 @@ &saradc {
 	vref-supply = <&vddio_ao1v8>;
 };
 
+/* SDIO wifi */
+&sdhc {
+	status = "okay";
+
+	pinctrl-0 = <&sdxc_a_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	disable-wp;
+	non-removable;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+};
+
 &sdio {
 	status = "okay";
 
@@ -222,6 +262,12 @@ &uart_A {
 	pinctrl-0 = <&uart_a1_pins>, <&uart_a1_cts_rts_pins>;
 	pinctrl-names = "default";
 	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm20702a1";
+		shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+	};
 };
 
 &uart_AO {
-- 
2.40.0