Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
Date:   Tue, 21 Mar 2023 19:50:47 -0700
From:   Bjorn Andersson <andersson@kernel.org>
To:     Konrad Dybcio <konrad.dybcio@linaro.org>
Cc:     Bartosz Golaszewski <brgl@bgdev.pl>,
        Andy Gross <agross@kernel.org>,
        Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
        linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org,
        Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Subject: Re: [PATCH v2 12/15] arm64: dts: qcom: sa8775p: pmic: add thermal
 zones
Message-ID: <20230322025047.gvo252mh2flcbzuc@ripper>
References: <20230320154841.327908-1-brgl@bgdev.pl>
 <20230320154841.327908-13-brgl@bgdev.pl>
 <a215c54b-c12e-4463-f9fe-588053f74300@linaro.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
In-Reply-To: <a215c54b-c12e-4463-f9fe-588053f74300@linaro.org>
Precedence: bulk

On Mon, Mar 20, 2023 at 06:28:20PM +0100, Konrad Dybcio wrote:
> 
> 
> On 20.03.2023 16:48, Bartosz Golaszewski wrote:
> > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > 
> > Add the thermal zones and associated alarm nodes for the PMICs that have
> > them hooked up on sa8775p-ride.
> > 
> > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 58 +++++++++++++++++++++
> >  1 file changed, 58 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> > index 8616ead3daf5..276070b62ccd 100644
> > --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> > @@ -6,6 +6,50 @@
> >  #include <dt-bindings/input/input.h>
> >  #include <dt-bindings/spmi/spmi.h>
> >  
> > +/ {
> > +	thermal-zones {
> > +		pmm8654au_1_thermal: pm8775-1-thermal {
> Please reindex this, downstream uses _1 for pmic@0, but this
> makes little sense. Make it match the SID.
> 

Please use the naming from the schematics for these things, rather than
just an iterator (which might be what Bartosz is doing here).

Regards,
Bjorn

> > +			polling-delay-passive = <100>;
> > +			polling-delay = <0>;
> > +			thermal-sensors = <&pmm8654au_1_temp_alarm>;
> > +
> > +			trips {
> > +				trip0 {
> > +					temperature = <105000>;
> > +					hysteresis = <0>;
> > +					type = "passive";
> > +				};
> > +
> > +				trip1 {
> > +					temperature = <125000>;
> > +					hysteresis = <0>;
> > +					type = "critical";
> > +				};
> > +			};
> > +		};
> > +
> What happened to the downstream _2 (pmic@2) one and _4 (pmic@6)?
> 
> Konrad
> 
> > +		pmm8654au_3_thermal: pm8775-3-thermal {
> > +			polling-delay-passive = <100>;
> > +			polling-delay = <0>;
> > +			thermal-sensors = <&pmm8654au_3_temp_alarm>;
> > +
> > +			trips {
> > +				trip0 {
> > +					temperature = <105000>;
> > +					hysteresis = <0>;
> > +					type = "passive";
> > +				};
> > +
> > +				trip1 {
> > +					temperature = <125000>;
> > +					hysteresis = <0>;
> > +					type = "critical";
> > +				};
> > +			};
> > +		};
> > +	};
> > +};
> > +
> >  &spmi_bus {
> >  	pmm8654au_0: pmic@0 {
> >  		compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
> > @@ -41,6 +85,13 @@ pmm8654au_1: pmic@2 {
> >  		reg = <0x2 SPMI_USID>;
> >  		#address-cells = <1>;
> >  		#size-cells = <0>;
> > +
> > +		pmm8654au_1_temp_alarm: temp-alarm@a00 {
> > +			compatible = "qcom,spmi-temp-alarm";
> > +			reg = <0xa00>;
> > +			interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> > +			#thermal-sensor-cells = <0>;
> > +		};
> >  	};
> >  
> >  	pmm8654au_2: pmic@4 {
> > @@ -55,5 +106,12 @@ pmm8654au_3: pmic@6 {
> >  		reg = <0x6 SPMI_USID>;
> >  		#address-cells = <1>;
> >  		#size-cells = <0>;
> > +
> > +		pmm8654au_3_temp_alarm: temp-alarm@a00 {
> > +			compatible = "qcom,spmi-temp-alarm";
> > +			reg = <0xa00>;
> > +			interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> > +			#thermal-sensor-cells = <0>;
> > +		};
> >  	};
> >  };