Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Udit Kumar <u-kumar1@ti.com>
To:     <linux-arm-kernel@lists.infradead.org>, <afd@ti.com>, <bb@ti.com>,
        <vaishnav.a@ti.com>, <j-choudhary@ti.com>,
        <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
        <nm@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>,
        <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
        <a-govindraju@ti.com>, <kishon@ti.com>
CC:     Udit Kumar <u-kumar1@ti.com>, J Keerthi <j-keerthy@ti.com>
Subject: [PATCH 1/2] arm64: dts: ti: k3-j7200: Fix  physical address of pin
Date:   Fri, 14 Apr 2023 23:44:33 +0530
Message-ID: <20230414181434.2046049-2-u-kumar1@ti.com>
In-Reply-To: <20230414181434.2046049-1-u-kumar1@ti.com>
References: <20230414181434.2046049-1-u-kumar1@ti.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Content-Type: text/plain
Precedence: bulk

Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")

wkup_pmx splits into multiple regions. Like

    wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
    wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
    wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
    wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)

With this split, pin offset needs to be adjusted to
match with new pmx for all pins above wkup_pmx0.

Example a pin under wkup_pmx1 should start from 0 instead of
old offset(0x38 WKUP_PADCONFIG 14 offset)

J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
            https://www.ti.com/lit/ds/symlink/dra821u.pdf

Signed-off-by: J Keerthi <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
 .../dts/ti/k3-j7200-common-proc-board.dts     | 28 +++++++++----------
 1 file changed, 14 insertions(+), 14 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 0d39d6b8cc0c..63633e4f6c59 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -83,25 +83,25 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
 &wkup_pmx2 {
 	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
-			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
-			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
-			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
-			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
-			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
-			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
-			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
-			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
-			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
-			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
-			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
-			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+			J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+			J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+			J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+			J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+			J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+			J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+			J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
 		>;
 	};
 
 	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
-			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
-			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
+			J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
+			J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
 		>;
 	};
 };
-- 
2.34.1