Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Udit Kumar <u-kumar1@ti.com>
To:     <linux-arm-kernel@lists.infradead.org>, <afd@ti.com>, <bb@ti.com>,
        <vaishnav.a@ti.com>, <j-choudhary@ti.com>,
        <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
        <nm@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>,
        <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>
CC:     Udit Kumar <u-kumar1@ti.com>
Subject: [PATCH v3 2/2] arm64: dts: ti: k3-j7200-som: Enable I2C
Date:   Wed, 19 Apr 2023 09:30:07 +0530
Message-ID: <20230419040007.3022780-3-u-kumar1@ti.com>
In-Reply-To: <20230419040007.3022780-1-u-kumar1@ti.com>
References: <20230419040007.3022780-1-u-kumar1@ti.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Content-Type: text/plain
Precedence: bulk

This patch enables wkup_i2c0 node in board dts file
along with pin mux and speed.
Also enables underneath eeprom CAV24C256WE.

J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
https://www.ti.com/lit/ds/symlink/dra821u.pdf

J7200 User Guide (Section 4.3, Table 4-2) :
https://www.ti.com/lit/ug/spruiw7a/spruiw7a.pdf

Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index fa44ed4c17d5..269424154771 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -118,6 +118,15 @@ J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0)  /* MCU_OSPI0_DQS */
 	};
 };
 
+&wkup_pmx2 {
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+			pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
+			J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
+		>;
+	};
+};
+
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-pins-default {
 		pinctrl-single,pins = <
@@ -214,6 +223,18 @@ exp_som: gpio@21 {
 	};
 };
 
+&wkup_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+};
+
 &ospi0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
-- 
2.34.1