Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Boerge Struempfel <boerge.struempfel@gmail.com>
Cc:     boerge.struempfel@gmail.com, bstruempfel@ultratronik.de,
        andy.shevchenko@gmail.com, festevam@gmail.com,
        amit.kumar-mahapatra@amd.com, broonie@kernel.org,
        Shawn Guo <shawnguo@kernel.org>,
        Sascha Hauer <s.hauer@pengutronix.de>,
        Pengutronix Kernel Team <kernel@pengutronix.de>,
        NXP Linux Team <linux-imx@nxp.com>,
        linux-spi@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
        linux-kernel@vger.kernel.org
Subject: [PATCH v5 1/4] spi: add SPI_MOSI_IDLE_LOW mode bit
Date:   Sat, 20 May 2023 21:08:52 +0200
Message-Id: <20230520190856.34720-2-boerge.struempfel@gmail.com>
In-Reply-To: <20230520190856.34720-1-boerge.struempfel@gmail.com>
References: <20230520190856.34720-1-boerge.struempfel@gmail.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
To:     unlisted-recipients:; (no To-header on input)
Precedence: bulk

Some spi controller switch the mosi line to high, whenever they are
idle. This may not be desired in all use cases. For example neopixel
leds can get confused and flicker due to misinterpreting the idle state.
Therefore, we introduce a new spi-mode bit, with which the idle behaviour
can be overwritten on a per device basis.

Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
---
 include/uapi/linux/spi/spi.h | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/include/uapi/linux/spi/spi.h b/include/uapi/linux/spi/spi.h
index 9d5f58059703..ca56e477d161 100644
--- a/include/uapi/linux/spi/spi.h
+++ b/include/uapi/linux/spi/spi.h
@@ -28,6 +28,7 @@
 #define	SPI_RX_OCTAL		_BITUL(14)	/* receive with 8 wires */
 #define	SPI_3WIRE_HIZ		_BITUL(15)	/* high impedance turnaround */
 #define	SPI_RX_CPHA_FLIP	_BITUL(16)	/* flip CPHA on Rx only xfer */
+#define SPI_MOSI_IDLE_LOW	_BITUL(17)	/* leave mosi line low when idle */
 
 /*
  * All the bits defined above should be covered by SPI_MODE_USER_MASK.
@@ -37,6 +38,6 @@
  * These bits must not overlap. A static assert check should make sure of that.
  * If adding extra bits, make sure to increase the bit index below as well.
  */
-#define SPI_MODE_USER_MASK	(_BITUL(17) - 1)
+#define SPI_MODE_USER_MASK	(_BITUL(18) - 1)
 
 #endif /* _UAPI_SPI_H */
-- 
2.25.1