Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   arinc9.unal@gmail.com
To:     Sean Wang <sean.wang@mediatek.com>,
        Landen Chao <Landen.Chao@mediatek.com>,
        DENG Qingfang <dqfext@gmail.com>,
        Daniel Golle <daniel@makrotopia.org>,
        Andrew Lunn <andrew@lunn.ch>,
        Florian Fainelli <f.fainelli@gmail.com>,
        Vladimir Oltean <olteanv@gmail.com>,
        "David S. Miller" <davem@davemloft.net>,
        Eric Dumazet <edumazet@google.com>,
        Jakub Kicinski <kuba@kernel.org>,
        Paolo Abeni <pabeni@redhat.com>,
        Matthias Brugger <matthias.bgg@gmail.com>,
        AngeloGioacchino Del Regno 
        <angelogioacchino.delregno@collabora.com>,
        Russell King <linux@armlinux.org.uk>
Cc:     =?UTF-8?q?Ar=C4=B1n=C3=A7=20=C3=9CNAL?= <arinc.unal@arinc9.com>,
        Richard van Schagen <richard@routerhints.com>,
        Richard van Schagen <vschagen@cs.com>,
        Frank Wunderlich <frank-w@public-files.de>,
        Bartel Eerdekens <bartel.eerdekens@constell8.be>,
        erkin.bozoglu@xeront.com, mithat.guner@xeront.com,
        netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
        linux-arm-kernel@lists.infradead.org,
        linux-mediatek@lists.infradead.org
Subject: [PATCH net-next 06/30] net: dsa: mt7530: improve code path for setting up port 5
Date:   Mon, 22 May 2023 15:15:08 +0300
Message-Id: <20230522121532.86610-7-arinc.unal@arinc9.com>
In-Reply-To: <20230522121532.86610-1-arinc.unal@arinc9.com>
References: <20230522121532.86610-1-arinc.unal@arinc9.com>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
Precedence: bulk

From: Arınç ÜNAL <arinc.unal@arinc9.com>

There're two code paths for setting up port 5:

mt7530_setup()
-> mt7530_setup_port5()

mt753x_phylink_mac_config()
-> mt753x_mac_config()
   -> mt7530_mac_config()
      -> mt7530_setup_port5()

Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
is used as a CPU, DSA, or user port, mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
set on mt7530_setup_port5() will match state->interface on
mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
again.

mt7530_setup_port5() from mt753x_phylink_mac_config() won't run when port 5
is disabled or used for PHY muxing as port 5 won't be defined on the
devicetree.

Therefore, mt7530_setup_port5() will never run from
mt753x_phylink_mac_config().

Address this by not running mt7530_setup_port5() from mt7530_setup() if
port 5 is used as a CPU, DSA, or user port. For the cases of PHY muxing or
the port being disabled, call mt7530_setup_port5() from mt7530_setup().

Do not set priv->p5_interface on mt7530_setup_port5(). There won't be a
case where mt753x_phylink_mac_config() runs after mt7530_setup_port5()
anymore.

Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
"priv" is allocated.

Move setting the interface to a more specific location. It's supposed to be
overwritten if PHY muxing is detected.

Improve the comment which explains the process.

Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
---
 drivers/net/dsa/mt7530.c | 19 ++++++++-----------
 1 file changed, 8 insertions(+), 11 deletions(-)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 1a842d6fbc27..b8f159afcd45 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -965,8 +965,6 @@ static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
 	dev_dbg(ds->dev, "Setup P5, HWTRAP=0x%x, intf_sel=%s, phy-mode=%s\n",
 		val, p5_intf_modes(priv->p5_intf_sel), phy_modes(interface));
 
-	priv->p5_interface = interface;
-
 unlock_exit:
 	mutex_unlock(&priv->reg_mutex);
 }
@@ -2274,16 +2272,15 @@ mt7530_setup(struct dsa_switch *ds)
 		return ret;
 
 	/* Setup port 5 */
-	priv->p5_intf_sel = P5_DISABLED;
-	interface = PHY_INTERFACE_MODE_NA;
-
 	if (!dsa_is_unused_port(ds, 5)) {
 		priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
-		ret = of_get_phy_mode(dsa_to_port(ds, 5)->dn, &interface);
-		if (ret && ret != -ENODEV)
-			return ret;
 	} else {
-		/* Scan the ethernet nodes. look for GMAC1, lookup used phy */
+		/* Scan the ethernet nodes. Look for GMAC1, lookup the used PHY.
+		 * Set priv->p5_intf_sel to the appropriate value if PHY muxing
+		 * is detected.
+		 */
+		interface = PHY_INTERFACE_MODE_NA;
+
 		for_each_child_of_node(dn, mac_np) {
 			if (!of_device_is_compatible(mac_np,
 						     "mediatek,eth-mac"))
@@ -2314,6 +2311,8 @@ mt7530_setup(struct dsa_switch *ds)
 			of_node_put(phy_node);
 			break;
 		}
+
+		mt7530_setup_port5(ds, interface);
 	}
 
 #ifdef CONFIG_GPIOLIB
@@ -2324,8 +2323,6 @@ mt7530_setup(struct dsa_switch *ds)
 	}
 #endif /* CONFIG_GPIOLIB */
 
-	mt7530_setup_port5(ds, interface);
-
 	/* Flush the FDB table */
 	ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
 	if (ret < 0)
-- 
2.39.2