Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Vinod Koul <vkoul@kernel.org>
To:     Bjorn Andersson <andersson@kernel.org>
Cc:     linux-arm-msm@vger.kernel.org,
        Konrad Dybcio <konrad.dybcio@linaro.org>,
        Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Conor Dooley <conor+dt@kernel.org>, devicetree@vger.kernel.org,
        linux-kernel@vger.kernel.org, Vinod Koul <vkoul@kernel.org>
Subject: [PATCH v3 10/15] arm64: dts: qcom: sc8180x: Add PCIe instances
Date:   Tue, 30 May 2023 21:54:49 +0530
Message-Id: <20230530162454.51708-11-vkoul@kernel.org>
In-Reply-To: <20230530162454.51708-1-vkoul@kernel.org>
References: <20230530162454.51708-1-vkoul@kernel.org>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

This patch adds PCIe instances found on this SoC

Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
 arch/arm64/boot/dts/qcom/sc8180x.dtsi | 429 ++++++++++++++++++++++++++
 1 file changed, 429 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc8180x.dtsi b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
index b50673b7c147..2639f5fb6e39 100644
--- a/arch/arm64/boot/dts/qcom/sc8180x.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
@@ -1681,6 +1681,435 @@ mmss_noc: interconnect@1740000 {
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		pcie0: pci@1c00000 {
+			compatible = "qcom,pcie-sc8180x";
+			reg = <0 0x01c00000 0 0x3000>,
+			      <0 0x60000000 0 0xf1d>,
+			      <0 0x60000f20 0 0xa8>,
+			      <0 0x60001000 0 0x1000>,
+			      <0 0x60100000 0 0x100000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x60200000 0x0 0x60200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
+				 <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ref",
+				      "tbu";
+
+			assigned-clocks = <&gcc GCC_PCIE_0_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			iommus = <&apps_smmu 0x1d80 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1d80 0x1>,
+				    <0x100 &apps_smmu 0x1d81 0x1>;
+
+			resets = <&gcc GCC_PCIE_0_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_0_GDSC>;
+
+			interconnects = <&aggre2_noc MASTER_PCIE 0 &mc_virt SLAVE_EBI_CH0 0>,
+					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			phys = <&pcie0_lane>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie0_phy: phy-wrapper@1c06000 {
+			compatible = "qcom,sc8180x-qmp-pcie-phy";
+			reg = <0 0x1c06000 0 0x1c0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_CLK>,
+				 <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE0_PHY_REFGEN_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie0_lane: phy@1c06200 {
+				reg = <0 0x1c06200 0 0x170>, /* tx0 */
+				      <0 0x1c06400 0 0x200>, /* rx0 */
+				      <0 0x1c06a00 0 0x1f0>, /* pcs */
+				      <0 0x1c06600 0 0x170>, /* tx1 */
+				      <0 0x1c06800 0 0x200>, /* rx1 */
+				      <0 0x1c06e00 0 0xf4>; /* pcs_com */
+				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#clock-cells = <0>;
+				clock-output-names = "pcie_0_pipe_clk";
+				#phy-cells = <0>;
+			};
+		};
+
+		pcie3: pci@1c08000 {
+			compatible = "qcom,pcie-sc8180x";
+			reg = <0 0x01c08000 0 0x3000>,
+			      <0 0x40000000 0 0xf1d>,
+			      <0 0x40000f20 0 0xa8>,
+			      <0 0x40001000 0 0x1000>,
+			      <0 0x40100000 0 0x100000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config";
+			device_type = "pci";
+			linux,pci-domain = <3>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_3_PIPE_CLK>,
+				 <&gcc GCC_PCIE_3_AUX_CLK>,
+				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_3_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_3_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_3_CLKREF_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ref",
+				      "tbu";
+
+			assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			iommus = <&apps_smmu 0x1e00 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1e00 0x1>,
+				    <0x100 &apps_smmu 0x1e01 0x1>;
+
+			resets = <&gcc GCC_PCIE_3_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_3_GDSC>;
+
+			interconnects = <&aggre2_noc MASTER_PCIE_3 0 &mc_virt SLAVE_EBI_CH0 0>,
+					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			phys = <&pcie3_lane>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie3_phy: phy-wrapper@1c0c000 {
+			compatible = "qcom,sc8180x-qmp-pcie-phy";
+			reg = <0 0x1c0c000 0 0x1c0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_3_CLKREF_CLK>,
+				 <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_3_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE3_PHY_REFGEN_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie3_lane: phy@1c0c200 {
+				reg = <0 0x1c0c200 0 0x170>, /* tx0 */
+				      <0 0x1c0c400 0 0x200>, /* rx0 */
+				      <0 0x1c0ca00 0 0x1f0>, /* pcs */
+				      <0 0x1c0c600 0 0x170>, /* tx1 */
+				      <0 0x1c0c800 0 0x200>, /* rx1 */
+				      <0 0x1c0ce00 0 0xf4>; /* pcs_com */
+				clocks = <&gcc GCC_PCIE_3_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#clock-cells = <0>;
+				clock-output-names = "pcie_3_pipe_clk";
+				#phy-cells = <0>;
+			};
+		};
+
+		pcie1: pci@1c10000 {
+			compatible = "qcom,pcie-sc8180x";
+			reg = <0 0x01c10000 0 0x3000>,
+			      <0 0x68000000 0 0xf1d>,
+			      <0 0x68000f20 0 0xa8>,
+			      <0 0x68001000 0 0x1000>,
+			      <0 0x68100000 0 0x100000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x68200000 0x0 0x68200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x68300000 0x0 0x68300000 0x0 0x3d00000>;
+
+			interrupts = <GIC_SPI 755 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 747 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 746 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 745 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 744 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+				 <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_CLKREF_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ref",
+				      "tbu";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			iommus = <&apps_smmu 0x1c80 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1c80 0x1>,
+				    <0x100 &apps_smmu 0x1c81 0x1>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_1_GDSC>;
+
+			interconnects = <&aggre2_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI_CH0 0>,
+					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			phys = <&pcie1_lane>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy-wrapper@1c16000 {
+			compatible = "qcom,sc8180x-qmp-pcie-phy";
+			reg = <0 0x1c16000 0 0x1c0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_CLKREF_CLK>,
+				 <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie1_lane: phy@1c0e200 {
+				reg = <0 0x1c16200 0 0x170>, /* tx0 */
+				      <0 0x1c16400 0 0x200>, /* rx0 */
+				      <0 0x1c16a00 0 0x1f0>, /* pcs */
+				      <0 0x1c16600 0 0x170>, /* tx1 */
+				      <0 0x1c16800 0 0x200>, /* rx1 */
+				      <0 0x1c16e00 0 0xf4>; /* pcs_com */
+				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
+				clock-names = "pipe0";
+				#clock-cells = <0>;
+				clock-output-names = "pcie_1_pipe_clk";
+
+				#phy-cells = <0>;
+			};
+		};
+
+		pcie2: pci@1c18000 {
+			compatible = "qcom,pcie-sc8180x";
+			reg = <0 0x01c18000 0 0x3000>,
+			      <0 0x70000000 0 0xf1d>,
+			      <0 0x70000f20 0 0xa8>,
+			      <0 0x70001000 0 0x1000>,
+			      <0 0x70100000 0 0x100000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config";
+			device_type = "pci";
+			linux,pci-domain = <2>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <4>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x70200000 0x0 0x70200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x3d00000>;
+
+			interrupts = <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 663 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 662 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 661 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 660 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_2_PIPE_CLK>,
+				 <&gcc GCC_PCIE_2_AUX_CLK>,
+				 <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_2_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_2_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_2_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_2_CLKREF_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ref",
+				      "tbu";
+
+			assigned-clocks = <&gcc GCC_PCIE_2_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			iommus = <&apps_smmu 0x1d00 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1d00 0x1>,
+				    <0x100 &apps_smmu 0x1d01 0x1>;
+
+			resets = <&gcc GCC_PCIE_2_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_2_GDSC>;
+
+			interconnects = <&aggre2_noc MASTER_PCIE_2 0 &mc_virt SLAVE_EBI_CH0 0>,
+					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			phys = <&pcie2_lane>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie2_phy: phy-wrapper@1c1c000 {
+			compatible = "qcom,sc8180x-qmp-pcie-phy";
+			reg = <0 0x1c1c000 0 0x1c0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_2_CLKREF_CLK>,
+				 <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_2_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie2_lane: phy@1c0e200 {
+				reg = <0 0x1c1c200 0 0x170>, /* tx0 */
+				      <0 0x1c1c400 0 0x200>, /* rx0 */
+				      <0 0x1c1ca00 0 0x1f0>, /* pcs */
+				      <0 0x1c1c600 0 0x170>, /* tx1 */
+				      <0 0x1c1c800 0 0x200>, /* rx1 */
+				      <0 0x1c1ce00 0 0xf4>; /* pcs_com */
+				clocks = <&gcc GCC_PCIE_2_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#clock-cells = <0>;
+				clock-output-names = "pcie_2_pipe_clk";
+
+				#phy-cells = <0>;
+			};
+		};
+
 		ufs_mem_hc: ufshc@1d84000 {
 			compatible = "qcom,sc8180x-ufshc", "qcom,ufshc",
 				     "jedec,ufs-2.0";
-- 
2.40.1