Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Neil Armstrong <neil.armstrong@linaro.org>
Subject: [PATCH RFC 0/7] arm64: qcom: add Type-C Altmode support
Date:   Thu, 01 Jun 2023 16:07:00 +0200
Message-Id: <20230601-topic-sm8550-upstream-type-c-v1-0-d4d97b4d8bab@linaro.org>
MIME-Version: 1.0
Content-Type: text/plain; charset="utf-8"
Content-Transfer-Encoding: 7bit
To:     Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Conor Dooley <conor+dt@kernel.org>,
        Andy Gross <agross@kernel.org>,
        Bjorn Andersson <andersson@kernel.org>,
        Konrad Dybcio <konrad.dybcio@linaro.org>,
        Heikki Krogerus <heikki.krogerus@linux.intel.com>,
        Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc:     Rob Herring <robh@kernel.org>, devicetree@vger.kernel.org,
        linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
        linux-usb@vger.kernel.org,
        Neil Armstrong <neil.armstrong@linaro.org>
Precedence: bulk

This adds the missing bits to support the USB-C Altmode
support on SM8550.

These are the following changes since the previous SM8450 SoC:
- No more GLINK altmode events for USB only changes, only DP
- Type-C orientation is available on a PMIC signal connected
  to a GPIO line
- When altmode is disconnected, an 0xff mode event is sent.

In order to handle those changes, a new orientation-gpios property
is added to the usb-c connector bindings.
The 0xff altomode is translated as a SAFE type-c mux mode.

And in order to handle such info, we tie this to the UCSI connector
events to propagate the orientation to Type-C switches.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Neil Armstrong (7):
      dt-bindings: connector: usb-connector: add a gpio used to determine the Type-C port plug orientation
      soc: qcom: pmic_glink_altmode: handle safe mode when disconnect
      usb: ucsi: glink: use the connector orientation GPIO to provide switch events
      qcom: pmic_glink: enable altmode for SM8550
      arm64: dts: qcom: sm8550: add ports subnodes in usb/dp qmpphy node
      arm64: dts: qcom: sm8550-mtp: add pmic glink port/endpoints
      arm64: dts: qcom: sm8550-qrd: add pmic glink port/endpoints

 .../bindings/connector/usb-connector.yaml          |  5 ++
 arch/arm64/boot/dts/qcom/sm8550-mtp.dts            | 67 ++++++++++++++-
 arch/arm64/boot/dts/qcom/sm8550-qrd.dts            | 99 +++++++++++++++++++++-
 arch/arm64/boot/dts/qcom/sm8550.dtsi               | 26 ++++++
 drivers/soc/qcom/pmic_glink.c                      |  6 +-
 drivers/soc/qcom/pmic_glink_altmode.c              | 18 +++-
 drivers/usb/typec/ucsi/ucsi_glink.c                | 52 +++++++++++-
 7 files changed, 262 insertions(+), 11 deletions(-)
---
base-commit: f339b18115200db76b42475e44e3bc926e3ecab0
change-id: 20230601-topic-sm8550-upstream-type-c-e85b4d971450

Best regards,
-- 
Neil Armstrong <neil.armstrong@linaro.org>