Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Nishanth Menon <nm@ti.com>
To:     Conor Dooley <conor+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Rob Herring <robh+dt@kernel.org>,
        Tero Kristo <kristo@kernel.org>,
        Vignesh Raghavendra <vigneshr@ti.com>
CC:     <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
        <linux-arm-kernel@lists.infradead.org>, Nishanth Menon <nm@ti.com>,
        Udit Kumar <u-kumar1@ti.com>,
        Neha Malcom Francis <n-francis@ti.com>
Subject: [PATCH 6/9] arm64: dts: ti: k3-j721e-beagleboneai64: Add wakeup_uart pinmux
Date:   Thu, 1 Jun 2023 13:31:48 -0500
Message-ID: <20230601183151.1000157-7-nm@ti.com>
In-Reply-To: <20230601183151.1000157-1-nm@ti.com>
References: <20230601183151.1000157-1-nm@ti.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Content-Type: text/plain
Precedence: bulk

Define the wakeup uart pin-mux for completeness. This allows the
device tree usage in bootloader and firmwares that can configure the
same appropriately.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts b/arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts
index c13246a9ed8f..bc53ca566a68 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts
@@ -531,6 +531,13 @@ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
 		>;
 	};
 
+	wkup_uart0_pins_default: wkup-uart0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xa0, PIN_INPUT, 0) /* (J29) WKUP_UART0_RXD */
+			J721E_WKUP_IOPAD(0xa4, PIN_OUTPUT, 0) /* (J28) WKUP_UART0_TXD */
+		>;
+	};
+
 	mcu_usbss1_pins_default: mcu-usbss1-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x3c, PIN_OUTPUT_PULLUP, 5) /* (A23) MCU_OSPI1_LBCLKO.WKUP_GPIO0_30 */
@@ -541,6 +548,8 @@ J721E_WKUP_IOPAD(0x3c, PIN_OUTPUT_PULLUP, 5) /* (A23) MCU_OSPI1_LBCLKO.WKUP_GPIO
 &wkup_uart0 {
 	/* Wakeup UART is used by TIFS firmware. */
 	status = "reserved";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_uart0_pins_default>;
 };
 
 &main_uart0 {
-- 
2.40.0