Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Hugo Villeneuve <hugo@hugovil.com>
To:     gregkh@linuxfoundation.org, robh+dt@kernel.org,
        krzysztof.kozlowski+dt@linaro.org, conor+dt@kernel.org,
        jirislaby@kernel.org, jringle@gridpoint.com,
        tomasz.mon@camlingroup.com, l.perczak@camlintechnologies.com
Cc:     linux-serial@vger.kernel.org, devicetree@vger.kernel.org,
        linux-kernel@vger.kernel.org, hugo@hugovil.com,
        linux-gpio@vger.kernel.org,
        Hugo Villeneuve <hvilleneuve@dimonoff.com>,
        stable@vger.kernel.org, Lech Perczak <lech.perczak@camlingroup.com>
Date:   Thu,  1 Jun 2023 16:18:41 -0400
Message-Id: <20230601201844.3739926-7-hugo@hugovil.com>
In-Reply-To: <20230601201844.3739926-1-hugo@hugovil.com>
References: <20230601201844.3739926-1-hugo@hugovil.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Subject: [PATCH v6 6/9] serial: sc16is7xx: fix bug when first setting GPIO direction
Precedence: bulk

From: Hugo Villeneuve <hvilleneuve@dimonoff.com>

When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.

By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.

Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.

This is what is done in NXP application note AN10587.

Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
---
 drivers/tty/serial/sc16is7xx.c | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index ad6b9d613b33..2fa09baf28e3 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -1340,9 +1340,18 @@ static int sc16is7xx_gpio_direction_output(struct gpio_chip *chip,
 		state |= BIT(offset);
 	else
 		state &= ~BIT(offset);
-	sc16is7xx_port_write(port, SC16IS7XX_IOSTATE_REG, state);
+
+	/*
+	 * If we write IOSTATE first, and then IODIR, the output value is not
+	 * transferred to the corresponding I/O pin.
+	 * The datasheet states that each register bit will be transferred to
+	 * the corresponding I/O pin programmed as output when writing to
+	 * IOSTATE. Therefore, configure direction first with IODIR, and then
+	 * set value after with IOSTATE.
+	 */
 	sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset),
 			      BIT(offset));
+	sc16is7xx_port_write(port, SC16IS7XX_IOSTATE_REG, state);
 
 	return 0;
 }
-- 
2.30.2