Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Chen-Yu Tsai <wenst@chromium.org>
To:     Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Conor Dooley <conor+dt@kernel.org>,
        Mark Brown <broonie@kernel.org>,
        Liam Girdwood <lgirdwood@gmail.com>,
        Matthias Brugger <matthias.bgg@gmail.com>,
        AngeloGioacchino Del Regno 
        <angelogioacchino.delregno@collabora.com>
Cc:     Chen-Yu Tsai <wenst@chromium.org>, devicetree@vger.kernel.org,
        linux-arm-kernel@lists.infradead.org,
        linux-mediatek@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH 7/9] regulator: mt6358: Add output voltage fine tuning to fixed regulators
Date:   Fri,  9 Jun 2023 16:30:04 +0800
Message-ID: <20230609083009.2822259-8-wenst@chromium.org>
In-Reply-To: <20230609083009.2822259-1-wenst@chromium.org>
References: <20230609083009.2822259-1-wenst@chromium.org>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

The "fixed" LDO regulators found on the MT6358 and MT6366 PMICs have
either no voltage selection register, or only one valid setting.
However these do have a fine voltage calibration setting that can
slightly boost the output voltage from 0 mV to 100 mV, in 10 mV
increments.

Add support for this by changing these into linear range regulators.

Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
---
 drivers/regulator/mt6358-regulator.c | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/regulator/mt6358-regulator.c b/drivers/regulator/mt6358-regulator.c
index 31a16fb28ecd..26060909cf90 100644
--- a/drivers/regulator/mt6358-regulator.c
+++ b/drivers/regulator/mt6358-regulator.c
@@ -123,10 +123,13 @@ struct mt6358_regulator_info {
 		.type = REGULATOR_VOLTAGE,	\
 		.id = MT6358_ID_##vreg,	\
 		.owner = THIS_MODULE,	\
-		.n_voltages = 1,	\
+		.n_voltages = 11,	\
+		.vsel_reg = MT6358_##vreg##_ANA_CON0,	\
+		.vsel_mask = GENMASK(3, 0),	\
 		.enable_reg = enreg,	\
 		.enable_mask = BIT(enbit),	\
 		.min_uV = volt,	\
+		.uV_step = 10000, \
 	},	\
 	.status_reg = MT6358_LDO_##vreg##_CON1,	\
 	.qi = BIT(15),							\
@@ -219,10 +222,13 @@ struct mt6358_regulator_info {
 		.type = REGULATOR_VOLTAGE,	\
 		.id = MT6366_ID_##vreg,	\
 		.owner = THIS_MODULE,	\
-		.n_voltages = 1,	\
+		.n_voltages = 11,	\
+		.vsel_reg = MT6358_##vreg##_ANA_CON0,	\
+		.vsel_mask = GENMASK(3, 0),	\
 		.enable_reg = enreg,	\
 		.enable_mask = BIT(enbit),	\
 		.min_uV = volt,	\
+		.uV_step = 10000, \
 	},	\
 	.status_reg = MT6358_LDO_##vreg##_CON1,	\
 	.qi = BIT(15),							\
@@ -476,8 +482,13 @@ static const struct regulator_ops mt6358_volt_table_ops = {
 	.get_status = mt6358_get_status,
 };
 
+/* "Fixed" LDOs with output voltage calibration +0 ~ +10 mV */
 static const struct regulator_ops mt6358_volt_fixed_ops = {
 	.list_voltage = regulator_list_voltage_linear,
+	.map_voltage = regulator_map_voltage_linear,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = mt6358_get_buck_voltage_sel,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.is_enabled = regulator_is_enabled_regmap,
-- 
2.41.0.162.gfafddb0af9-goog