Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Sridharan S N <quic_sridsn@quicinc.com>
To:     <agross@kernel.org>, <andersson@kernel.org>,
        <konrad.dybcio@linaro.org>, <robh+dt@kernel.org>,
        <krzysztof.kozlowski+dt@linaro.org>, <conor+dt@kernel.org>,
        <linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
        <linux-kernel@vger.kernel.org>
CC:     Sridharan S N <quic_sridsn@quicinc.com>
Subject: [PATCH V4 2/2] arm64: dts: qcom: ipq9574: enable GPIO based LEDs
Date:   Fri, 16 Jun 2023 14:02:38 +0530
Message-ID: <20230616083238.20690-3-quic_sridsn@quicinc.com>
In-Reply-To: <20230616083238.20690-1-quic_sridsn@quicinc.com>
References: <20230616083238.20690-1-quic_sridsn@quicinc.com>
MIME-Version: 1.0
Content-Type: text/plain
Precedence: bulk

Add support for wlan-2g LED on GPIO 64.

Signed-off-by: Sridharan S N <quic_sridsn@quicinc.com>
---
Changes in V4:
	- Added patch dependency. This change depends on below patch set
	  https://lore.kernel.org/linux-arm-msm/20230614085040.22071-2-quic_anusha@quicinc.com/

Changes in V3:
	- Updated patch series title. Mentioned platform in series
	  title

Changes in V2:
	- No changes
 
.../boot/dts/qcom/ipq9574-rdp-common.dtsi     | 20 +++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi b/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
index fd5326dc1773..25424cecd834 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
@@ -34,6 +34,18 @@
 			debounce-interval = <60>;
 		};
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&gpio_leds_default>;
+		pinctrl-names = "default";
+
+		led-0 {
+			gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+	};
 };
 
 &blsp1_spi0 {
@@ -137,6 +149,14 @@
 		drive-strength = <8>;
 		bias-pull-up;
 	};
+
+	gpio_leds_default: gpio-leds-default-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
 };
 
 &xo_board_clk {
-- 
2.17.1