Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   John Watts <contact@jookia.org>
To:     linux-sunxi@lists.linux.dev
Cc:     Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Conor Dooley <conor+dt@kernel.org>,
        Paul Walmsley <paul.walmsley@sifive.com>,
        Palmer Dabbelt <palmer@dabbelt.com>,
        Albert Ou <aou@eecs.berkeley.edu>,
        Chen-Yu Tsai <wens@csie.org>,
        Jernej Skrabec <jernej.skrabec@gmail.com>,
        Samuel Holland <samuel@sholland.org>,
        Maksim Kiselev <bigunclemax@gmail.com>,
        Marc Kleine-Budde <mkl@pengutronix.de>,
        John Watts <contact@jookia.org>,
        Cristian Ciocaltea <cristian.ciocaltea@collabora.com>,
        devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
        linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH v3] riscv: dts: allwinner: d1: Add CAN controller nodes
Date:   Tue,  8 Aug 2023 05:19:52 +1000
Message-ID: <20230807191952.2019208-1-contact@jookia.org>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

The Allwinner D1, T113 provide two CAN controllers that are variants
of the R40 controller.

I have tested support for these controllers on two boards:

- A Lichee Panel RV 86 Panel running a D1 chip
- A Mango Pi MQ Dual running a T113-s3 chip

Both of these fully support both CAN controllers.

Signed-off-by: John Watts <contact@jookia.org>
---
Changes in v3:
- Set default pinctrl for can controller
- Moved can nodes to proper location
- Moved can pins to proper location

 .../boot/dts/allwinner/sunxi-d1s-t113.dtsi    | 34 +++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
index d59b4acf183a..24f2e70d5886 100644
--- a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
+++ b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
@@ -52,6 +52,18 @@ pio: pinctrl@2000000 {
 			#gpio-cells = <3>;
 			#interrupt-cells = <3>;
 
+			/omit-if-no-ref/
+			can0_pins: can0-pins {
+				pins = "PB2", "PB3";
+				function = "can0";
+			};
+
+			/omit-if-no-ref/
+			can1_pins: can1-pins {
+				pins = "PB4", "PB5";
+				function = "can1";
+			};
+
 			/omit-if-no-ref/
 			clk_pg11_pin: clk-pg11-pin {
 				pins = "PG11";
@@ -356,6 +368,28 @@ i2c3: i2c@2502c00 {
 			#size-cells = <0>;
 		};
 
+		can0: can@2504000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&can0_pins>;
+			compatible = "allwinner,sun20i-d1-can";
+			reg = <0x02504000 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(21) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CAN0>;
+			resets = <&ccu RST_BUS_CAN0>;
+			status = "disabled";
+		};
+
+		can1: can@2504400 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&can1_pins>;
+			compatible = "allwinner,sun20i-d1-can";
+			reg = <0x02504400 0x400>;
+			interrupts = <SOC_PERIPHERAL_IRQ(22) IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CAN1>;
+			resets = <&ccu RST_BUS_CAN1>;
+			status = "disabled";
+		};
+
 		syscon: syscon@3000000 {
 			compatible = "allwinner,sun20i-d1-system-control";
 			reg = <0x3000000 0x1000>;
-- 
2.41.0