Received: by 2002:a05:6359:6284:b0:131:369:b2a3 with SMTP id se4csp5241271rwb; Wed, 9 Aug 2023 00:27:40 -0700 (PDT) X-Google-Smtp-Source: AGHT+IHyAewNYDucGHcw4iC76B+yyDWY8Rgtpkmy5KiptG7atcQ8PUBmc3JdytO2impawqE4ZkIK X-Received: by 2002:a17:906:154:b0:99b:d098:1ffd with SMTP id 20-20020a170906015400b0099bd0981ffdmr1508591ejh.62.1691566059815; Wed, 09 Aug 2023 00:27:39 -0700 (PDT) ARC-Seal: i=1; a=rsa-sha256; t=1691566059; cv=none; d=google.com; s=arc-20160816; b=XbYf2OBKSmA/FVqXxZsqRpSo2KvFC9PsqU9ReyjLJ0ctHiI10a/WzSaW33Zgfz2gYU 6gLBxWkEW99sg/6EKqpnXD+GRlyUMf4vbd+LXMFz/G8RTkz5uRFUb0JpWMuUPyVGN4/B px0MvHtjfS89lMX3xeQHdPqGkECDnrheUgXRc8XBhaemwS8+CL2vpDxHwSJui6i15BAy 5SUh9eQMF7IlVAjthsADhR6cNygNKm3BcODB3o0o2DQwnLa05lndrst+EGTUWyY3rzrP woHhskTY5EQWrdsWyqa9C5ReId42KdT5NkaO9NSJVplNMQ7tI2i6t8tg93ZTJb684keS QZ/Q== ARC-Message-Signature: i=1; a=rsa-sha256; c=relaxed/relaxed; d=google.com; s=arc-20160816; h=list-id:precedence:content-transfer-encoding:mime-version :references:in-reply-to:message-id:date:subject:cc:to:from; bh=z8e9w7VCGgp0N1ICNUx04kNRKBFw2okOWpSLPokndgI=; fh=wIyLjtWa5IUWDggL4LUubQn5CllRxeq3nPju63OhZzo=; b=Y2UkIFVjInm9wMsfKOhaEhJrtMYwMMXM/PG0AgMrU2sxMjKQ+bcOUUWGITk2z6MG2j s/Z/jFT6+S7w41xT52XhFQje8oxomSYqCLK+taz31FJTP1V2LSp5fj2oqzPsRRQCul3X Jipq6uk0QvPD2x7vBj9LoB1CR6tIcgPmeRAFe4fVIZcYONHB2TNfo5208a10eAVp8pjH r0t4PNvIQUsYZP1JWw/YKQKMgbnwoJsIZRSlqoYNmwXVYH/AP9Y9UY31+xg6V/crSaia g43rfnQ00FdmF+AvRbHEsrPDy23ulqkKq4f+FRqjUTXFXDEdAC9Mv9B05A3Zulw1vgAI JE5w== ARC-Authentication-Results: i=1; mx.google.com; spf=pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) smtp.mailfrom=linux-kernel-owner@vger.kernel.org Return-Path: Received: from out1.vger.email (out1.vger.email. [2620:137:e000::1:20]) by mx.google.com with ESMTP id l18-20020a1709066b9200b0099cbe6d4e20si6270686ejr.112.2023.08.09.00.27.14; Wed, 09 Aug 2023 00:27:39 -0700 (PDT) Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20; Authentication-Results: mx.google.com; spf=pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) smtp.mailfrom=linux-kernel-owner@vger.kernel.org Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S231556AbjHIHLA (ORCPT + 99 others); Wed, 9 Aug 2023 03:11:00 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:50656 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S231509AbjHIHKo (ORCPT ); Wed, 9 Aug 2023 03:10:44 -0400 Received: from metis.ext.pengutronix.de (metis.ext.pengutronix.de [IPv6:2001:67c:670:201:290:27ff:fe1d:cc33]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id BD9E11FE2 for ; Wed, 9 Aug 2023 00:10:42 -0700 (PDT) Received: from dude02.red.stw.pengutronix.de ([2a0a:edc0:0:1101:1d::28]) by metis.ext.pengutronix.de with esmtp (Exim 4.92) (envelope-from ) id 1qTdKx-0003NV-8V; Wed, 09 Aug 2023 09:10:31 +0200 From: Marco Felsch To: robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org, conor+dt@kernel.org, shawnguo@kernel.org, kernel@pengutronix.de, festevam@gmail.com, linux-imx@nxp.com, laurent.pinchart@ideasonboard.com, dan.scally@ideasonboard.com Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org Subject: [PATCH v4 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support Date: Wed, 9 Aug 2023 09:10:26 +0200 Message-Id: <20230809071026.3546605-4-m.felsch@pengutronix.de> X-Mailer: git-send-email 2.39.2 In-Reply-To: <20230809071026.3546605-1-m.felsch@pengutronix.de> References: <20230809071026.3546605-1-m.felsch@pengutronix.de> MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit X-SA-Exim-Connect-IP: 2a0a:edc0:0:1101:1d::28 X-SA-Exim-Mail-From: m.felsch@pengutronix.de X-SA-Exim-Scanned: No (on metis.ext.pengutronix.de); SAEximRunCond expanded to false X-PTX-Original-Recipient: linux-kernel@vger.kernel.org X-Spam-Status: No, score=-1.9 required=5.0 tests=BAYES_00, RCVD_IN_DNSWL_BLOCKED,SPF_HELO_NONE,SPF_PASS autolearn=unavailable autolearn_force=no version=3.4.6 X-Spam-Checker-Version: SpamAssassin 3.4.6 (2021-04-09) on lindbergh.monkeyblade.net Precedence: bulk List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Add support for the Debix SOM A + SOM A I/O board. The commit enables only the basic features like: - 2x UART - 2x Network - eMMC/µSD - CAN - QSPI - USB Host / Device Signed-off-by: Marco Felsch Reviewed-by: Fabio Estevam --- Changelog: v4: - no changes v3: - add ethernet-mac-addr nvmem cells - reorder MACs - fix newline issues - align regulator gpio and enable-active-high - fix i2c-device order - move regulator-usdhc2 to som.dtsi (incl. iomuxc) - use phy-addr <1> instead of broadcast <0> - drop regulator-always-on for regulator-baseboard-vdd3v3 v2: - drop to generic polyhex,imx8mp-debix binding - net/phy: replace deprecated snps,reset-* and phy-reset-* bindings with new phy-node based ones - net/phy: fix phy properties and reset timings - net/phy: add fec phy-supply handling - net/phy: add eqos phy-supply handling - net/phy: fix baseboard-vdd3v3 timings to fulfill net-phy-timings - Fix spelling - Drop superfluous blank lines - pmic: make use of IRQ_TYPE_LEVEL_LOW - pmic: add whitespace between buck node name and '{' arch/arm64/boot/dts/freescale/Makefile | 1 + .../freescale/imx8mp-debix-som-a-bmb-08.dts | 472 ++++++++++++++++++ .../dts/freescale/imx8mp-debix-som-a.dtsi | 285 +++++++++++ 3 files changed, 758 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index a750be13ace8..13275684ddfd 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-som-a-bmb-08.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts new file mode 100644 index 000000000000..0b0c95432bdc --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts @@ -0,0 +1,472 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2019 NXP + * Copyright (C) 2023 Pengutronix, Marco Felsch + */ + +/dts-v1/; + +#include "imx8mp-debix-som-a.dtsi" + +/ { + model = "Polyhex i.MX8MPlus Debix SOM A on BMB-08"; + compatible = "polyhex,imx8mp-debix-som-a-bmb-08", "polyhex,imx8mp-debix-som-a", + "fsl,imx8mp"; + + aliases { + ethernet0 = &eqos; + ethernet1 = &fec; + }; + + chosen { + stdout-path = &uart2; + }; + + reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "BB_VDD3V3"; + /* Required timings for ethernet phy's */ + startup-delay-us = <50000>; + off-on-delay-us = <110000>; + gpio = <&expander0 10 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_baseboard_vdd5v0: regulator-baseboard-vdd5v0 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "BB_VDD5V"; + gpio = <&expander0 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + regulator-som-vdd1v8 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "SOM_VDD1V8_SW"; + gpio = <&expander0 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + regulator-som-vdd3v3 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "SOM_VDD3V3_SW"; + gpio = <&expander0 11 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + regulator-vbus-usb20 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "USB20_5V"; + gpio = <&expander1 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + vin-supply = <®_baseboard_vdd5v0>; + }; + + regulator-vbus-usb30 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "USB30_5V"; + gpio = <&expander1 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + vin-supply = <®_baseboard_vdd5v0>; + }; + + reg_vdd5v0: regulator-vdd5v0 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-name = "VDD_5V"; + gpio = <&expander0 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + nvmem-cells = <ðmac1>; + nvmem-cell-names = "mac-address"; + phy-supply = <®_baseboard_vdd3v3>; + phy-handle = <ðphy0>; + phy-mode = "rgmii-id"; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>; + reset-assert-us = <20000>; + reset-deassert-us = <150000>; + eee-broken-1000t; + realtek,clkout-disable; + }; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + nvmem-cells = <ðmac2>; + nvmem-cell-names = "mac-address"; + phy-supply = <®_baseboard_vdd3v3>; + phy-handle = <ðphy1>; + phy-mode = "rgmii-id"; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>; + reset-assert-us = <20000>; + reset-deassert-us = <150000>; + eee-broken-1000t; + realtek,clkout-disable; + }; + }; +}; + +&flexcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_vdd5v0>; + status = "okay"; +}; + +&flexcan2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + xceiver-supply = <®_vdd5v0>; + status = "okay"; +}; + +&flexspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexspi0>; + status = "okay"; + + flash: flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&i2c4 { + expander0: gpio@20 { + compatible = "nxp,pca9535"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <0x02>; + }; + + expander1: gpio@23 { + compatible = "nxp,pca9535"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <0x02>; + + /* + * Since USB1 is bound to peripheral mode we need to ensure + * that VBUS is turned off. + */ + usb30-otg-hog { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "USB30_OTG_EN"; + }; + }; + + rtc@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc>; + interrupt-parent = <&gpio4>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + #clock-cells = <0>; + }; + + eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + #address-cells = <1>; + #size-cells = <0>; + + /* MACs stored in ASCII */ + ethmac1: mac-address@0 { + reg = <0x0 0xc>; + }; + + ethmac2: mac-address@c { + reg = <0xc 0xc>; + }; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +/* Debug */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&usb_dwc3_0 { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usb_dwc3_1 { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + /* 2.x hub on port 1 */ + usb_hub_2_x: hub@1 { + compatible = "usb5e3,610"; + reg = <1>; + reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>; + vdd-supply = <®_vdd5v0>; + peer-hub = <&usb_hub_3_x>; + }; + + /* 3.x hub on port 2 */ + usb_hub_3_x: hub@2 { + compatible = "usb5e3,620"; + reg = <2>; + reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>; + vdd-supply = <®_vdd5v0>; + peer-hub = <&usb_hub_2_x>; + }; +}; + +&usb3_phy0 { + status = "okay"; +}; + +&usb3_phy1 { + status = "okay"; +}; + +/* µSD Card */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + assigned-clocks = <&clk IMX8MP_CLK_USDHC2>; + assigned-clock-rates = <400000000>; + vmmc-supply = <®_usdhc2_vmmc>; + bus-width = <4>; + disable-wp; + no-sdio; + no-mmc; + status = "okay"; +}; + +&iomuxc { + pinctrl_eqos: eqosgrp { + fsl,pins = < + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3 + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3 + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91 + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91 + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91 + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91 + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91 + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f + + MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN 0x1f + MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x19 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3 + MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3 + MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91 + MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91 + MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91 + MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91 + MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91 + MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f + MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f + MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f + MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f + MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f + MX8MP_IOMUXC_SAI1_RXD0__ENET1_1588_EVENT1_IN 0x1f + MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x19 + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX 0x154 + MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX 0x154 + >; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX 0x154 + MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX 0x154 + >; + }; + + pinctrl_flexspi0: flexspi0grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK 0x1c2 + MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B 0x82 + MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00 0x82 + MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01 0x82 + MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02 0x82 + MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2 + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3 + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_rtc: rtcgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x140 + >; + }; + + pinctrl_pmic: pmicgrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x14f + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x14f + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x49 + MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x49 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x49 + MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x49 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi new file mode 100644 index 000000000000..bc312aa1bfc8 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi @@ -0,0 +1,285 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2019 NXP + * Copyright (C) 2023 Pengutronix, Marco Felsch + */ + +#include "imx8mp.dtsi" + +/ { + model = "Polyhex i.MX8MPlus Debix SOM A"; + compatible = "polyhex,imx8mp-debix-som-a", "fsl,imx8mp"; + + reg_usdhc2_vmmc: regulator-usdhc2 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&A53_0 { + cpu-supply = <&buck2>; +}; + +&A53_1 { + cpu-supply = <&buck2>; +}; + +&A53_2 { + cpu-supply = <&buck2>; +}; + +&A53_3 { + cpu-supply = <&buck2>; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@25 { + compatible = "nxp,pca9450c"; + reg = <0x25>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + regulators { + buck1: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + buck2: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; + }; + + buck4: BUCK4 { + regulator-name = "BUCK4"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5: BUCK5 { + regulator-name = "BUCK5"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6: BUCK6 { + regulator-name = "BUCK6"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5: LDO5 { + regulator-name = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c4 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + adc@48 { + compatible = "ti,ads1115"; + reg = <0x48>; + #address-cells = <1>; + #size-cells = <0>; + + channel@4 { + reg = <4>; + ti,gain = <1>; + ti,datarate = <7>; + }; + + channel@5 { + reg = <5>; + ti,gain = <1>; + ti,datarate = <7>; + }; + + channel@6 { + reg = <6>; + ti,gain = <1>; + ti,datarate = <7>; + }; + + channel@7 { + reg = <7>; + ti,gain = <1>; + ti,datarate = <7>; + }; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + assigned-clocks = <&clk IMX8MP_CLK_USDHC3>; + assigned-clock-rates = <400000000>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2 + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3 + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_pmic: pmicgrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41 + >; + }; + + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6 + >; + }; +}; -- 2.39.2