Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.37 as permitted sender) client-ip=23.128.96.37;
From:   Claudiu <claudiu.beznea@tuxon.dev>
To:     geert+renesas@glider.be, mturquette@baylibre.com, sboyd@kernel.org,
        robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org,
        conor+dt@kernel.org, linus.walleij@linaro.org,
        gregkh@linuxfoundation.org, jirislaby@kernel.org,
        magnus.damm@gmail.com, catalin.marinas@arm.com, will@kernel.org,
        quic_bjorande@quicinc.com, konrad.dybcio@linaro.org, arnd@arndb.de,
        neil.armstrong@linaro.org, prabhakar.mahadev-lad.rj@bp.renesas.com,
        biju.das.jz@bp.renesas.com
Cc:     linux-renesas-soc@vger.kernel.org, linux-clk@vger.kernel.org,
        devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
        linux-gpio@vger.kernel.org, linux-serial@vger.kernel.org,
        linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 02/28] clk: renesas: rzg2l: wait for status bit of SD mux before continuing
Date:   Fri, 29 Sep 2023 08:38:49 +0300
Message-Id: <20230929053915.1530607-3-claudiu.beznea@bp.renesas.com>
In-Reply-To: <20230929053915.1530607-1-claudiu.beznea@bp.renesas.com>
References: <20230929053915.1530607-1-claudiu.beznea@bp.renesas.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>

Hardware user manual of RZ/G2L (r01uh0914ej0130-rzg2l-rzg2lc.pdf,
chapter 7.4.7 Procedure for Switching Clocks by the Dynamic Switching
Frequency Selectors) specifies that we need to check CPG_PL2SDHI_DSEL for
SD clock switching status.

Fixes: eaff33646f4cb ("clk: renesas: rzg2l: Add SDHI clk mux support")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
---

Changes in v2:
- initialized msk

 drivers/clk/renesas/rzg2l-cpg.c | 17 ++++++++++-------
 1 file changed, 10 insertions(+), 7 deletions(-)

diff --git a/drivers/clk/renesas/rzg2l-cpg.c b/drivers/clk/renesas/rzg2l-cpg.c
index 9baae7bb7094..5343d04fd70d 100644
--- a/drivers/clk/renesas/rzg2l-cpg.c
+++ b/drivers/clk/renesas/rzg2l-cpg.c
@@ -188,7 +188,8 @@ static int rzg2l_cpg_sd_clk_mux_set_parent(struct clk_hw *hw, u8 index)
 	u32 off = GET_REG_OFFSET(hwdata->conf);
 	u32 shift = GET_SHIFT(hwdata->conf);
 	const u32 clk_src_266 = 2;
-	u32 bitmask;
+	u32 msk, val, bitmask;
+	int ret;
 
 	/*
 	 * As per the HW manual, we should not directly switch from 533 MHz to
@@ -202,14 +203,10 @@ static int rzg2l_cpg_sd_clk_mux_set_parent(struct clk_hw *hw, u8 index)
 	 * the index to value mapping is done by adding 1 to the index.
 	 */
 	bitmask = (GENMASK(GET_WIDTH(hwdata->conf) - 1, 0) << shift) << 16;
+	msk = off ? CPG_CLKSTATUS_SELSDHI1_STS : CPG_CLKSTATUS_SELSDHI0_STS;
 	if (index != clk_src_266) {
-		u32 msk, val;
-		int ret;
-
 		writel(bitmask | ((clk_src_266 + 1) << shift), priv->base + off);
 
-		msk = off ? CPG_CLKSTATUS_SELSDHI1_STS : CPG_CLKSTATUS_SELSDHI0_STS;
-
 		ret = readl_poll_timeout(priv->base + CPG_CLKSTATUS, val,
 					 !(val & msk), 100,
 					 CPG_SDHI_CLK_SWITCH_STATUS_TIMEOUT_US);
@@ -221,7 +218,13 @@ static int rzg2l_cpg_sd_clk_mux_set_parent(struct clk_hw *hw, u8 index)
 
 	writel(bitmask | ((index + 1) << shift), priv->base + off);
 
-	return 0;
+	ret = readl_poll_timeout(priv->base + CPG_CLKSTATUS, val,
+				 !(val & msk), 100,
+				 CPG_SDHI_CLK_SWITCH_STATUS_TIMEOUT_US);
+	if (ret)
+		dev_err(priv->dev, "failed to switch clk source\n");
+
+	return ret;
 }
 
 static u8 rzg2l_cpg_sd_clk_mux_get_parent(struct clk_hw *hw)
-- 
2.39.2