Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.35 as permitted sender) client-ip=23.128.96.35;
From:   Tony Lindgren <tony@atomide.com>
To:     Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
        Jiri Slaby <jirislaby@kernel.org>,
        Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc:     Andy Shevchenko <andriy.shevchenko@intel.com>,
        Dhruva Gole <d-gole@ti.com>,
        =?UTF-8?q?Ilpo=20J=C3=A4rvinen?= <ilpo.jarvinen@linux.intel.com>,
        John Ogness <john.ogness@linutronix.de>,
        Johan Hovold <johan@kernel.org>,
        Sebastian Andrzej Siewior <bigeasy@linutronix.de>,
        Vignesh Raghavendra <vigneshr@ti.com>,
        linux-kernel@vger.kernel.org, linux-serial@vger.kernel.org,
        Maximilian Luz <luzmaximilian@gmail.com>
Subject: [PATCH] serial: core: Fix checks for tx runtime PM state
Date:   Thu,  5 Oct 2023 10:56:42 +0300
Message-ID: <20231005075644.25936-1-tony@atomide.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

Maximilian reported that surface_serial_hub serdev tx does not work during
system suspend. During system suspend, runtime PM gets disabled in
__device_suspend_late(), and tx is unable to wake-up the serial core port
device that we use to check if tx is safe to start. Johan summarized the
regression noting that serdev tx no longer always works as earlier when the
serdev device is runtime PM active.

The serdev device and the serial core controller devices are siblings of
the serial port hardware device. The runtime PM usage count from serdev
device does not propagate to the serial core device siblings, it only
propagates to the parent.

In addition to the tx issue for suspend, testing for the serial core port
device can cause an unnecessary delay in enabling tx while waiting for the
serial core port device to wake-up. The serial core port device wake-up is
only needed to flush pending tx when the serial port hardware device was
in runtime PM suspended state.

To fix the regression, we need to check the runtime PM state of the parent
serial port hardware device for tx instead of the serial core port device.

As the serial port device drivers may or may not implement runtime PM, we
need to also add a check for pm_runtime_enabled().

Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 drivers/tty/serial/serial_core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -156,7 +156,7 @@ static void __uart_start(struct uart_state *state)
 	 * enabled, serial_port_runtime_resume() calls start_tx() again
 	 * after enabling the device.
 	 */
-	if (pm_runtime_active(&port_dev->dev))
+	if (!pm_runtime_enabled(port->dev) || pm_runtime_active(port->dev))
 		port->ops->start_tx(port);
 	pm_runtime_mark_last_busy(&port_dev->dev);
 	pm_runtime_put_autosuspend(&port_dev->dev);
-- 
2.42.0