Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::3:8 as permitted sender) client-ip=2620:137:e000::3:8;
From:   Jerome Brunet <jbrunet@baylibre.com>
To:     Neil Armstrong <neil.armstrong@linaro.org>,
        Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Conor Dooley <conor+dt@kernel.org>
Cc:     Jerome Brunet <jbrunet@baylibre.com>,
        Kevin Hilman <khilman@baylibre.com>,
        Da Xue <da.xue@libretech.co>, devicetree@vger.kernel.org,
        linux-kernel@vger.kernel.org, linux-amlogic@lists.infradead.org
Subject: [PATCH v2 0/2] arm64: dts: amlogic: add libretech cottonwood support
Date:   Fri,  6 Oct 2023 12:34:58 +0200
Message-Id: <20231006103500.2015183-1-jbrunet@baylibre.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

This patchset adds support for the Libretech cottonwood board family.
The 2 boards are based on the same PCB, with an RPi B form factor.

The "Alta" board uses an a311d while the "Solitude" variant uses an s905d3.

This patchset depends on the usb support for the gl3510 [1] and [6]
Without it, there will be dt check warnings and usb may not come up properly.

Early u-boot support may be found here [2]. It will be submitted after
DT is accepted in Linux. As usual with Amlogic, u-boot must be packaged
with closed source binaries ([3] for the a311d, [4] for the s905d3)

Prebuilt bootloaders are available from libretech [5].

The devices are shipped with libretech's u-boot pre-flashed in SPI NOR.
If necessary, the boot source may be changed to MMC using the onboard
switch.

Happy hacking ...

Changes since v1 [7]:
* Remove extra dvfs opps
* Rename Alsa cards
* Reorganize leds for DT schema while keeping meaningful node names
* Change blue LED trigger to heartbeat
* Set panic indicator on the orange LED
* Move hub reset from under the usb phy node to the controller one
* Drop npu node

[1]: https://lore.kernel.org/all/20231002122909.2338049-1-jbrunet@baylibre.com
[2]: https://gitlab.com/jbrunet/u-boot/-/tree/cottonwood
[3]: https://jbrunet.baylibre.com/pub/amlogic/fips/fip-collect-aml-a311d-cc-20230701.tar.gz
[4]: https://jbrunet.baylibre.com/pub/amlogic/fips/fip-collect-aml-s905d3-cc-20230820.tar.gz
[5]: https://boot.libre.computer/ci/
[6]: https://lore.kernel.org/all/20231006101028.1973730-1-jbrunet@baylibre.com
[7]: https://lore.kernel.org/all/20231002141020.2403652-1-jbrunet@baylibre.com

Jerome Brunet (2):
  dt-bindings: arm: amlogic: add libretech cottonwood support
  arm64: dts: amlogic: add libretech cottonwood support

 .../devicetree/bindings/arm/amlogic.yaml      |   2 +
 arch/arm64/boot/dts/amlogic/Makefile          |   2 +
 .../amlogic/meson-g12b-a311d-libretech-cc.dts | 121 ++++
 .../amlogic/meson-libretech-cottonwood.dtsi   | 614 ++++++++++++++++++
 .../amlogic/meson-sm1-s905d3-libretech-cc.dts |  89 +++
 5 files changed, 828 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-a311d-libretech-cc.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-libretech-cottonwood.dtsi
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-s905d3-libretech-cc.dts

-- 
2.40.1