Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.34 as permitted sender) client-ip=23.128.96.34;
MIME-Version: 1.0
Sensitivity: 
Importance: Normal
In-Reply-To: 
References: 
Subject: [PATCH v2] tty: serial: meson: hard LOCKUP on crtscts mode
From:   pkrasavin@imaqliq.ru
To:     Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
        Jiri Slaby <jirislaby@kernel.org>,
        Neil Armstrong <neil.armstrong@linaro.org>,
        Kevin Hilman <khilman@baylibre.com>,
        Jerome Brunet <jbrunet@baylibre.com>,
        Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc:     linux-kernel@vger.kernel.org, linux-serial@vger.kernel.org,
        linux-arm-kernel@lists.infradead.org,
        linux-amlogic@lists.infradead.org
Date:   Thu, 12 Oct 2023 13:22:41 +0000
Message-ID: <OF950BEF72.7F425944-ON00258A46.00488A76-00258A46.00497D44@gdc.ru>
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8BIT
Precedence: bulk

There might be hard lockup if we set crtscts mode on port without RTS/CTS configured:

# stty -F /dev/ttyAML6 crtscts; echo 1 > /dev/ttyAML6; echo 2 > /dev/ttyAML6
[   95.890386] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
[   95.890857] rcu:     3-...0: (201 ticks this GP) idle=e33c/1/0x4000000000000000 softirq=5844/5846 fqs=4984
[   95.900212] rcu:     (detected by 2, t=21016 jiffies, g=7753, q=296 ncpus=4)
[   95.906972] Task dump for CPU 3:
[   95.910178] task:bash            state:R  running task     stack:0     pid:205   ppid:1      flags:0x00000202
[   95.920059] Call trace:
[   95.922485]  __switch_to+0xe4/0x168
[   95.925951]  0xffffff8003477508
[   95.974379] watchdog: Watchdog detected hard LOCKUP on cpu 3
[   95.974424] Modules linked in: 88x2cs(O) rtc_meson_vrtc

Possible solution would be to not allow to setup crtscts on such port.

Tested on S905X3 based board.

Signed-off-by: Pavel Krasavin <pkrasavin@imaqliq.com>
---
v2: braces for single statement removed according to Dmitry's note
v1: https://lore.kernel.org/lkml/OF28B2B8C9.5BC0CD28-ON00258A46.0037688F-00258A46.0039155B@gdc.ru/
---

--- a/drivers/tty/serial/meson_uart.c	2023-10-12 15:44:02.410538523 +0300
+++ b/drivers/tty/serial/meson_uart.c	2023-10-12 15:58:06.242395253 +0300
@@ -380,10 +380,14 @@ static void meson_uart_set_termios(struc
 	else
 		val |= AML_UART_STOP_BIT_1SB;
 
-	if (cflags & CRTSCTS)
-		val &= ~AML_UART_TWO_WIRE_EN;
-	else
+	if (cflags & CRTSCTS) {
+		if (port->flags & UPF_HARD_FLOW)
+			val &= ~AML_UART_TWO_WIRE_EN;
+		else
+			termios->c_cflag &= ~CRTSCTS;
+	} else {
 		val |= AML_UART_TWO_WIRE_EN;
+	}
 
 	writel(val, port->membase + AML_UART_CONTROL);
 
@@ -705,6 +709,7 @@ static int meson_uart_probe(struct platf
 	u32 fifosize = 64; /* Default is 64, 128 for EE UART_0 */
 	int ret = 0;
 	int irq;
+	bool has_rtscts;
 
 	if (pdev->dev.of_node)
 		pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
@@ -732,6 +737,7 @@ static int meson_uart_probe(struct platf
 		return irq;
 
 	of_property_read_u32(pdev->dev.of_node, "fifo-size", &fifosize);
+	has_rtscts = of_property_read_bool(pdev->dev.of_node, "uart-has-rtscts");
 
 	if (meson_ports[pdev->id]) {
 		return dev_err_probe(&pdev->dev, -EBUSY,
@@ -762,6 +768,8 @@ static int meson_uart_probe(struct platf
 	port->mapsize = resource_size(res_mem);
 	port->irq = irq;
 	port->flags = UPF_BOOT_AUTOCONF | UPF_LOW_LATENCY;
+	if (has_rtscts)
+		port->flags |= UPF_HARD_FLOW;
 	port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_MESON_CONSOLE);
 	port->dev = &pdev->dev;
 	port->line = pdev->id;