Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::3:3 as permitted sender) client-ip=2620:137:e000::3:3;
From:   Emil Renner Berthing <emil.renner.berthing@canonical.com>
In-Reply-To: <20231029042712.520010-13-cristian.ciocaltea@collabora.com>
References: <20231029042712.520010-1-cristian.ciocaltea@collabora.com> <20231029042712.520010-13-cristian.ciocaltea@collabora.com>
Mime-Version: 1.0
Date:   Sun, 26 Nov 2023 22:10:57 +0100
Message-ID: <CAJM55Z9e=vjGKNnmURN15mvXo2bVd3igBA-3puF9q7eh5hiP+A@mail.gmail.com>
Subject: Re: [PATCH v2 12/12] [UNTESTED] riscv: dts: starfive:
 beaglev-starlight: Enable gmac
To:     Cristian Ciocaltea <cristian.ciocaltea@collabora.com>,
        "David S. Miller" <davem@davemloft.net>,
        Eric Dumazet <edumazet@google.com>,
        Jakub Kicinski <kuba@kernel.org>,
        Paolo Abeni <pabeni@redhat.com>,
        Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Conor Dooley <conor+dt@kernel.org>,
        Emil Renner Berthing <kernel@esmil.dk>,
        Samin Guo <samin.guo@starfivetech.com>,
        Paul Walmsley <paul.walmsley@sifive.com>,
        Palmer Dabbelt <palmer@dabbelt.com>,
        Albert Ou <aou@eecs.berkeley.edu>,
        Alexandre Torgue <alexandre.torgue@foss.st.com>,
        Jose Abreu <joabreu@synopsys.com>,
        Maxime Coquelin <mcoquelin.stm32@gmail.com>,
        Richard Cochran <richardcochran@gmail.com>,
        Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc:     netdev@vger.kernel.org, devicetree@vger.kernel.org,
        linux-kernel@vger.kernel.org, linux-riscv@lists.infradead.org,
        linux-stm32@st-md-mailman.stormreply.com,
        linux-arm-kernel@lists.infradead.org, kernel@collabora.com
Content-Type: text/plain; charset="UTF-8"
Precedence: bulk

Cristian Ciocaltea wrote:
> The BeagleV Starlight SBC uses a Microchip KSZ9031RNXCA PHY supporting
> RGMII-ID.
>
> TODO: Verify if manual adjustment of the RX internal delay is needed. If
> yes, add the mdio & phy sub-nodes.

Sorry for being late here. I've tested that removing the mdio and phy nodes on
the the Starlight board works fine, but the rx-internal-delay-ps = <900>
property not needed on any of my VisionFive V1 boards either. So I wonder why
you need that on your board

Also in the driver patch you add support for phy-mode = "rgmii-txid", but here
you still set it to "rgmii-id", so which is it?

You've alse removed the phy reset gpio on the Starlight board:

  snps,reset-gpios = <&gpio 63 GPIO_ACTIVE_LOW>

Why?

>
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
> ---
>  arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts | 5 +++++
>  1 file changed, 5 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts b/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts
> index 7cda3a89020a..d3f4c99d98da 100644
> --- a/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts
> +++ b/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts
> @@ -11,3 +11,8 @@ / {
>  	model = "BeagleV Starlight Beta";
>  	compatible = "beagle,beaglev-starlight-jh7100-r0", "starfive,jh7100";
>  };
> +
> +&gmac {
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +};

Lastly the phy-mode and status are the same for the VF1 and Starlight boards,
so why can't these be set in the jh7100-common.dtsi?

/Emil

> --
> 2.42.0
>