Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::3:2 as permitted sender) client-ip=2620:137:e000::3:2;
From:   Can Guo <quic_cang@quicinc.com>
To:     quic_cang@quicinc.com, bvanassche@acm.org, mani@kernel.org,
        adrian.hunter@intel.com, cmd4@qualcomm.com, beanhuo@micron.com,
        avri.altman@wdc.com, junwoo80.lee@samsung.com,
        martin.petersen@oracle.com
Cc:     linux-scsi@vger.kernel.org, linux-arm-msm@vger.kernel.org,
        Andy Gross <agross@kernel.org>,
        Bjorn Andersson <andersson@kernel.org>,
        Konrad Dybcio <konrad.dybcio@linaro.org>,
        "James E.J. Bottomley" <jejb@linux.ibm.com>,
        linux-kernel@vger.kernel.org (open list)
Subject: [PATCH v6 02/10] scsi: ufs: ufs-qcom: No need to set hs_rate after ufshcd_init_host_param()
Date:   Wed, 29 Nov 2023 00:28:27 -0800
Message-Id: <1701246516-11626-3-git-send-email-quic_cang@quicinc.com>
In-Reply-To: <1701246516-11626-1-git-send-email-quic_cang@quicinc.com>
References: <1701246516-11626-1-git-send-email-quic_cang@quicinc.com>
Precedence: bulk

In ufs_qcom_pwr_change_notify(), host_params.hs_rate has been set to
PA_HS_MODE_B by ufshcd_init_host_param(), hence remove the duplicated line
of work. Meanwhile, removed the macro UFS_QCOM_LIMIT_HS_RATE as it is only
used here.

Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
---
 drivers/ufs/host/ufs-qcom.c | 1 -
 drivers/ufs/host/ufs-qcom.h | 2 --
 2 files changed, 3 deletions(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 197c5a5..c21ff2c 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -909,7 +909,6 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 	switch (status) {
 	case PRE_CHANGE:
 		ufshcd_init_host_params(&host_params);
-		host_params.hs_rate = UFS_QCOM_LIMIT_HS_RATE;
 
 		/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
 		host_params.hs_tx_gear = host_params.hs_rx_gear = ufs_qcom_get_hs_gear(hba);
diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
index 9950a00..82cd143 100644
--- a/drivers/ufs/host/ufs-qcom.h
+++ b/drivers/ufs/host/ufs-qcom.h
@@ -27,8 +27,6 @@
 #define SLOW 1
 #define FAST 2
 
-#define UFS_QCOM_LIMIT_HS_RATE		PA_HS_MODE_B
-
 /* QCOM UFS host controller vendor specific registers */
 enum {
 	REG_UFS_SYS1CLK_1US                 = 0xC0,
-- 
2.7.4