Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.32 as permitted sender) client-ip=23.128.96.32;
From:   Anand Moon <linux.amoon@gmail.com>
To:     Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Conor Dooley <conor+dt@kernel.org>,
        Neil Armstrong <neil.armstrong@linaro.org>,
        Kevin Hilman <khilman@baylibre.com>,
        Jerome Brunet <jbrunet@baylibre.com>,
        Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc:     Anand Moon <linux.amoon@gmail.com>,
        linux-amlogic@lists.infradead.org, devicetree@vger.kernel.org,
        linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH v6 2/2] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2
Date:   Mon,  4 Dec 2023 20:14:26 +0530
Message-ID: <20231204144429.45197-3-linux.amoon@gmail.com>
In-Reply-To: <20231204144429.45197-1-linux.amoon@gmail.com>
References: <20231204144429.45197-1-linux.amoon@gmail.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

On Odroid n2/n2+ previously use gpio-hog to reset the usb hub,
switch to used on-board usb hub reset to enable the usb hub
and enable power to hub.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
V6:none
V5:none
V4:none
V3:none
V2:none
V1:none
---
 .../dts/amlogic/meson-g12b-odroid-n2.dtsi     | 36 ++++++++++++-------
 1 file changed, 24 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
index 91c9769fda20..9e671444eca6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -31,6 +31,30 @@ hub_5v: regulator-hub_5v {
 		enable-active-high;
 	};
 
+	/* USB hub supports both USB 2.0 and USB 3.0 root hub */
+	usb-hub {
+		dr_mode = "host";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* 2.0 hub on port 1 */
+		hub_2_0: hub@1 {
+			compatible = "usb5e3,610";
+			reg = <1>;
+			peer-hub = <&hub_3_0>;
+			vdd-supply = <&usb_pwr_en>;
+		};
+
+		/* 3.0 hub on port 4 */
+		hub_3_0: hub@2 {
+			compatible = "usb5e3,620";
+			reg = <2>;
+			peer-hub = <&hub_2_0>;
+			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+			vdd-supply = <&vcc_5v>;
+		};
+	};
+
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "ODROID-N2";
@@ -234,18 +258,6 @@ &gpio {
 		"PIN_3",  /* GPIOX_17 */
 		"PIN_5",  /* GPIOX_18 */
 		"PIN_36"; /* GPIOX_19 */
-	/*
-	 * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub-hog {
-		gpio-hog;
-		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
 };
 
 &i2c3 {
-- 
2.42.0