Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::3:8 as permitted sender) client-ip=2620:137:e000::3:8;
Date:   Tue, 12 Dec 2023 13:50:01 +0100
From:   Maxime Chevallier <maxime.chevallier@bootlin.com>
To:     Luo Jie <quic_luoj@quicinc.com>
Cc:     <agross@kernel.org>, <andersson@kernel.org>,
        <konrad.dybcio@linaro.org>, <davem@davemloft.net>,
        <edumazet@google.com>, <kuba@kernel.org>, <pabeni@redhat.com>,
        <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
        <conor+dt@kernel.org>, <andrew@lunn.ch>, <hkallweit1@gmail.com>,
        <linux@armlinux.org.uk>, <robert.marko@sartura.hr>,
        <linux-arm-msm@vger.kernel.org>, <netdev@vger.kernel.org>,
        <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
        <quic_srichara@quicinc.com>
Subject: Re: [PATCH v2 1/5] net: mdio: ipq4019: move eth_ldo_rdy before MDIO
 bus register
Message-ID: <20231212135001.6bf40e4d@device.home>
In-Reply-To: <20231212115151.20016-2-quic_luoj@quicinc.com>
References: <20231212115151.20016-1-quic_luoj@quicinc.com>
        <20231212115151.20016-2-quic_luoj@quicinc.com>
Organization: Bootlin
MIME-Version: 1.0
Content-Type: text/plain; charset=US-ASCII
Content-Transfer-Encoding: 7bit
Precedence: bulk

Hello,

On Tue, 12 Dec 2023 19:51:46 +0800
Luo Jie <quic_luoj@quicinc.com> wrote:

> The ethernet LDO provides the clock for the ethernet PHY that
> is connected with PCS, each LDO enables the clock output to
> each PCS, after the clock output enablement, the PHY GPIO reset
> can take effect.
> 
> For the PHY taking the MDIO bus level GPIO reset, the ethernet
> LDO should be enabled before the MDIO bus register.
> 
> For example, the qca8084 PHY takes the MDIO bus level GPIO
> reset for quad PHYs, there is another reason for qca8084 PHY
> using MDIO bus level GPIO reset instead of PHY level GPIO
> reset as below.
> 
> The work sequence of qca8084:
> 1. enable ethernet LDO.
> 2. GPIO reset on quad PHYs.
> 3. register clock provider based on MDIO device of qca8084.
> 4. PHY probe function called for initializing common clocks.
> 5. PHY capabilities acquirement.
> 
> If qca8084 takes PHY level GPIO reset in the step 4, the clock
> provider of qca8084 can't be registered correctly, since the
> clock parent(reading the current qca8084 hardware registers in
> step 3) of the registered clocks is deserted after GPIO reset.
> 
> There are two PCS(UNIPHY) supported in SOC side on ipq5332,
> and three PCS(UNIPHY) supported on ipq9574.
> 
> Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
> ---

[...]

> @@ -252,11 +244,32 @@ static int ipq4019_mdio_probe(struct platform_device *pdev)
>  	if (IS_ERR(priv->mdio_clk))
>  		return PTR_ERR(priv->mdio_clk);
>  
> -	/* The platform resource is provided on the chipset IPQ5018 */
> -	/* This resource is optional */
> -	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> -	if (res)
> -		priv->eth_ldo_rdy = devm_ioremap_resource(&pdev->dev, res);
> +	/* These platform resources are provided on the chipset IPQ5018 or
> +	 * IPQ5332.
> +	 */
> +	/* This resource are optional */
> +	for (index = 0; index < ETH_LDO_RDY_CNT; index++) {
> +		res = platform_get_resource(pdev, IORESOURCE_MEM, index + 1);
> +		if (res) {
> +			priv->eth_ldo_rdy[index] = devm_ioremap(&pdev->dev,
> +								res->start,
> +								resource_size(res));

You can simplify that sequence by using
devm_platform_get_and_ioremap_resource(), which will do both the
platform_get_resource and the devm_ioremap at once for you.

Thanks,

Maxime