Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1757224AbXLGUij (ORCPT ); Fri, 7 Dec 2007 15:38:39 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S1752186AbXLGUib (ORCPT ); Fri, 7 Dec 2007 15:38:31 -0500 Received: from threatwall.zlynx.org ([199.45.143.218]:34507 "EHLO zlynx.org" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1752053AbXLGUi2 (ORCPT ); Fri, 7 Dec 2007 15:38:28 -0500 Subject: 2.6.24-rc4-mm1 and Very Slow PCMCIA Compact Flash From: Zan Lynx To: Andrew Morton Cc: Linux Kernel , linux-pcmcia@lists.infradead.org Content-Type: multipart/signed; micalg=pgp-sha1; protocol="application/pgp-signature"; boundary="=-DWyxZK42HvbOby9x65V2" Date: Fri, 07 Dec 2007 20:38:24 +0000 Message-Id: <1197059904.15428.15.camel@localhost> Mime-Version: 1.0 X-Mailer: Evolution 2.12.2 X-Envelope-From: zlynx@acm.org X-Spam-Id: 20071207/1J0jxp-0000VB-Fs-linux-kernel@vger.kernel.org:zlynx@acm.org:199.45.143.218 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 47407 Lines: 1047 --=-DWyxZK42HvbOby9x65V2 Content-Type: text/plain Content-Transfer-Encoding: quoted-printable While I'm reporting problems I'll get this one out there. I normally use a USB-2 memory card reader but I also have a PCMCIA CompactFlash adapter that I use occasionally. During the MM series kernels 2.6.22 and 23 (I am pretty sure) this didn't work at all. I don't know about vanilla since I don't run that. Now with MM kernels 2.6.24 rc1-4 the PCMCIA adapter works again, but I only get read rates of 1.6 MB/s. When it used to work in 2.6.20 I got at least 16 MB/s. The card itself is capable of 30+ in the USB-2 reader. It might be that it auto-configures for PIO-0. I have no idea why it does that. Another interesting thing is that doing a dd to or from the card brings the rest of the system to a nearly complete halt. Interrupt problem? Here is dmesg: Linux version 2.6.24-rc4-mm1 (root@zephyr) (gcc version 4.2.2 (Gentoo 4.2.2= p1.0)) #1 SMP Thu Dec 6 14:05:21 MST 2007 Command line: root=3D/dev/sda2 rootfstype=3Dreiser4 rootflags=3Dno_write_ba= rrier,tmgr.atom_max_size=3D8000 ro i8042.nomux elevator=3Dcfq resume=3D/dev= /sda3 panic=3D5 nmi_watchdog=3D0,panic debug kernelcore=3D512M BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003ff70000 (usable) BIOS-e820: 000000003ff70000 - 000000003ff7f000 (ACPI data) BIOS-e820: 000000003ff7f000 - 000000003ff80000 (ACPI NVS) BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 262000) 1 entries of 256 used end_pfn_map =3D 1048576 DMI present. ACPI: RSDP 000F7240, 0014 (r0 PTLTD ) ACPI: RSDT 3FF7A87E, 0034 (r1 PTLTD RSDT 6040000 LTP 0) ACPI: FACP 3FF7EE13, 0074 (r1 NVIDIA CK8 6040000 PTL_ F4240) ACPI: DSDT 3FF7A8B2, 4561 (r1 NVIDIA CK8 6040000 MSFT 100000E) ACPI: FACS 3FF7FFC0, 0040 ACPI: APIC 3FF7EE87, 005A (r1 NVIDIA NV_APIC_ 6040000 LTP 0) ACPI: BOOT 3FF7EEE1, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) ACPI: SSDT 3FF7EF09, 00F7 (r1 PTLTD POWERNOW 6040000 LTP 1) Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 262000) 1 entries of 256 used No mptable found. [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0 [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001400000 on node 0 [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001800000 on node 0 [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001c00000 on node 0 [ffffe20000800000-ffffe200009fffff] PMD ->ffff810001e00000 on node 0 [ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002200000 on node 0 [ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002600000 on node 0 [ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002a00000 on node 0 [ffffe20001000000-ffffe200011fffff] PMD ->ffff810002c00000 on node 0 [ffffe20001200000-ffffe200013fffff] PMD ->ffff810003000000 on node 0 [ffffe20001400000-ffffe200015fffff] PMD ->ffff810003400000 on node 0 sizeof(struct page) =3D 88 Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 Movable zone start PFN for each node Node 0: 132096 early_node_map[2] active PFN ranges 0: 0 -> 159 0: 256 -> 262000 On node 0 totalpages: 261903 DMA zone: 88 pages used for memmap DMA zone: 2673 pages reserved DMA zone: 1238 pages, LIFO batch:0 DMA32 zone: 2750 pages used for memmap DMA32 zone: 125250 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Movable zone: 2790 pages used for memmap Movable zone: 127114 pages, LIFO batch:31 Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: IRQ9 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a000= 0 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d000= 0 swsusp: Registered nosave memory region: 00000000000d0000 - 000000000010000= 0 Allocating PCI resources starting at 50000000 (gap: 40000000:bff80000) SMP: Allowing 1 CPUs, 0 hotplug CPUs PERCPU: Allocating 35008 bytes of per cpu data Built 1 zonelists in Zone order, mobility grouping on. Total pages: 253602 Kernel command line: root=3D/dev/sda2 rootfstype=3Dreiser4 rootflags=3Dno_w= rite_barrier,tmgr.atom_max_size=3D8000 ro i8042.nomux elevator=3Dcfq resume= =3D/dev/sda3 panic=3D5 nmi_watchdog=3D0,panic debug kernelcore=3D512M Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) TSC calibrated against PM_TIMER time.c: Detected 797.941 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... MAX_LOCKDEP_SUBCLASSES: 8 ... MAX_LOCK_DEPTH: 30 ... MAX_LOCKDEP_KEYS: 2048 ... CLASSHASH_SIZE: 1024 ... MAX_LOCKDEP_ENTRIES: 8192 ... MAX_LOCKDEP_CHAINS: 16384 ... CHAINHASH_SIZE: 8192 memory used by lock dependency info: 1648 kB per task-struct memory footprint: 1680 bytes ------------------------ | Locking API testsuite: ---------------------------------------------------------------------------= - | spin |wlock |rlock |mutex | wsem | rsem = | -------------------------------------------------------------------------= - A-A deadlock: ok | ok | ok | ok | ok | ok = | A-B-B-A deadlock: ok | ok | ok | ok | ok | ok = | A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok = | A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok = | A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok = | A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok = | A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok = | double unlock: ok | ok | ok | ok | ok | ok = | initialize held: ok | ok | ok | ok | ok | ok = | bad unlock order: ok | ok | ok | ok | ok | ok = | -------------------------------------------------------------------------= - recursive read-lock: | ok | | ok = | recursive read-lock #2: | ok | | ok = | mixed read-write-lock: | ok | | ok = | mixed write-read-lock: | ok | | ok = | -------------------------------------------------------------------------= - hard-irqs-on + irq-safe-A/12: ok | ok | ok | soft-irqs-on + irq-safe-A/12: ok | ok | ok | hard-irqs-on + irq-safe-A/21: ok | ok | ok | soft-irqs-on + irq-safe-A/21: ok | ok | ok | sirq-safe-A =3D> hirqs-on/12: ok | ok | ok | sirq-safe-A =3D> hirqs-on/21: ok | ok | ok | hard-safe-A + irqs-on/12: ok | ok | ok | soft-safe-A + irqs-on/12: ok | ok | ok | hard-safe-A + irqs-on/21: ok | ok | ok | soft-safe-A + irqs-on/21: ok | ok | ok | hard-safe-A + unsafe-B #1/123: ok | ok | ok | soft-safe-A + unsafe-B #1/123: ok | ok | ok | hard-safe-A + unsafe-B #1/132: ok | ok | ok | soft-safe-A + unsafe-B #1/132: ok | ok | ok | hard-safe-A + unsafe-B #1/213: ok | ok | ok | soft-safe-A + unsafe-B #1/213: ok | ok | ok | hard-safe-A + unsafe-B #1/231: ok | ok | ok | soft-safe-A + unsafe-B #1/231: ok | ok | ok | hard-safe-A + unsafe-B #1/312: ok | ok | ok | soft-safe-A + unsafe-B #1/312: ok | ok | ok | hard-safe-A + unsafe-B #1/321: ok | ok | ok | soft-safe-A + unsafe-B #1/321: ok | ok | ok | hard-safe-A + unsafe-B #2/123: ok | ok | ok | soft-safe-A + unsafe-B #2/123: ok | ok | ok | hard-safe-A + unsafe-B #2/132: ok | ok | ok | soft-safe-A + unsafe-B #2/132: ok | ok | ok | hard-safe-A + unsafe-B #2/213: ok | ok | ok | soft-safe-A + unsafe-B #2/213: ok | ok | ok | hard-safe-A + unsafe-B #2/231: ok | ok | ok | soft-safe-A + unsafe-B #2/231: ok | ok | ok | hard-safe-A + unsafe-B #2/312: ok | ok | ok | soft-safe-A + unsafe-B #2/312: ok | ok | ok | hard-safe-A + unsafe-B #2/321: ok | ok | ok | soft-safe-A + unsafe-B #2/321: ok | ok | ok | hard-irq lock-inversion/123: ok | ok | ok | soft-irq lock-inversion/123: ok | ok | ok | hard-irq lock-inversion/132: ok | ok | ok | soft-irq lock-inversion/132: ok | ok | ok | hard-irq lock-inversion/213: ok | ok | ok | soft-irq lock-inversion/213: ok | ok | ok | hard-irq lock-inversion/231: ok | ok | ok | soft-irq lock-inversion/231: ok | ok | ok | hard-irq lock-inversion/312: ok | ok | ok | soft-irq lock-inversion/312: ok | ok | ok | hard-irq lock-inversion/321: ok | ok | ok | soft-irq lock-inversion/321: ok | ok | ok | hard-irq read-recursion/123: ok | soft-irq read-recursion/123: ok | hard-irq read-recursion/132: ok | soft-irq read-recursion/132: ok | hard-irq read-recursion/213: ok | soft-irq read-recursion/213: ok | hard-irq read-recursion/231: ok | soft-irq read-recursion/231: ok | hard-irq read-recursion/312: ok | soft-irq read-recursion/312: ok | hard-irq read-recursion/321: ok | soft-irq read-recursion/321: ok | ------------------------------------------------------- Good, all 218 testcases passed! | --------------------------------- Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Checking aperture... CPU 0: aperture @ e8000000 size 128 MB Memory: 1011836k/1048000k available (3418k kernel code, 34952k reserved, 16= 05k data, 1124k init) SLUB: Genslabs=3D11, HWalign=3D64, Order=3D0-1, MinObjects=3D4, CPUs=3D1, N= odes=3D1 Calibrating delay using timer specific routine.. 1597.27 BogoMIPS (lpj=3D79= 8637) Security Framework initialized Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) SMP alternatives: switching to UP code Freeing SMP alternatives: 25k freed ACPI: Core revision 20070126 Parsing all Control Methods: Table [DSDT](id 0001) - 650 Objects with 66 Devices 205 Methods 24 Regions Parsing all Control Methods: Table [SSDT](id 0002) - 3 Objects with 0 Devices 1 Methods 0 Regions tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquire= d evxfevnt-0091 [00] enable : Transition to ACPI mode successf= ul Using local APIC timer interrupts. APIC timer calibration result 12467833 Detected 12.467 MHz APIC timer. Brought up 1 CPUs CPU0 attaching NULL sched-domain. net_namespace: 240 bytes NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: Using configuration type 1 evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on in= t 0x9 evgpeblk-0956 [00] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on in= t 0x9 evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 5 Wake, Enabled 1 Runtime = GPEs in this block evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 1 Runtime = GPEs in this block ACPI: EC: Look up EC in DSDT Completing Region/Field/Buffer/Package initialization:.....................= ............................................... Initialized 24/24 Regions 2/2 Fields 28/29 Buffers 14/21 Packages (662 node= s) Initializing Device/Processor/Thermal objects by executing _INI methods:. Executed 1 _INI methods requiring 0 _STA executions (examined 70 objects) ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: EC: GPE =3D 0x21, I/O: command/status =3D 0x66, data =3D 0x62 ACPI: EC: driver started in poll mode ACPI: PCI Root Bridge [PCI0] (0000:00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 18 19) *0 ACPI: PCI Interrupt Link [LNK2] (IRQs 16 18 19) *0 ACPI: PCI Interrupt Link [LNK3] (IRQs 17) *0 ACPI: PCI Interrupt Link [LNK4] (IRQs 16 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs 16 18 19) *0 ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22) *0 ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered ACPI: EC: non-query interrupt received, switching to interrupt mode pnp: PnP ACPI: found 12 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=3Drouteirq". If it helps, post a r= eport PCI: Cannot allocate resource region 0 of device 0000:00:00.0 PCI: Cannot allocate resource region 4 of device 0000:00:01.1 PCI: Cannot allocate resource region 5 of device 0000:00:01.1 agpgart: Detected AGP bridge 0 agpgart: Setting up Nforce3 AGP. agpgart: AGP aperture is 128M @ 0xe8000000 Time: tsc clocksource has been installed. system 00:01: ioport range 0x8000-0x807f has been reserved system 00:01: ioport range 0x8080-0x80ff has been reserved system 00:01: ioport range 0x8400-0x847f has been reserved system 00:01: ioport range 0x8480-0x84ff has been reserved system 00:01: ioport range 0x8800-0x887f has been reserved system 00:01: ioport range 0x8880-0x88ff has been reserved system 00:01: ioport range 0x2040-0x207f has been reserved system 00:01: ioport range 0x2000-0x203f has been reserved system 00:02: iomem range 0xfff80000-0xffffffff could not be reserved system 00:02: iomem range 0xfec00000-0xfec00fff has been reserved system 00:02: iomem range 0xfee00000-0xfeefffff could not be reserved system 00:02: iomem range 0xfed00000-0xfed00fff has been reserved system 00:03: ioport range 0x200-0x20f has been reserved system 00:03: ioport range 0x680-0x6ff has been reserved system 00:03: ioport range 0x4d0-0x4d1 has been reserved system 00:03: ioport range 0xfe00-0xfe01 has been reserved PCI: Failed to allocate mem resource #10:4000000@e4000000 for 0000:02:04.0 PCI: Failed to allocate mem resource #10:4000000@e4000000 for 0000:02:04.1 PCI: Bus 3, cardbus bridge: 0000:02:04.0 IO window: 00003000-000030ff IO window: 00003400-000034ff PREFETCH window: 50000000-53ffffff PCI: Bus 7, cardbus bridge: 0000:02:04.1 IO window: 00003800-000038ff IO window: 00003c00-00003cff PREFETCH window: 54000000-57ffffff PCI: Bridge: 0000:00:0a.0 IO window: 3000-7fff MEM window: e0100000-e17fffff PREFETCH window: 50000000-57ffffff PCI: Failed to allocate mem resource #6:20000@e3000000 for 0000:01:00.0 PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: e2000000-e2ffffff PREFETCH window: f0000000-f80fffff PCI: Setting latency timer of device 0000:00:0a.0 to 64 ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 19 ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNK1] -> GSI 19 (level, low) -= > IRQ 19 ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18 ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LNK2] -> GSI 18 (level, low) -= > IRQ 18 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 9, 3670016 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Simple Boot Flag at 0x37 set to 0x1 audit: initializing netlink socket (disabled) audit(1197044649.870:1): initialized Total HugeTLB memory allocated, 0 Loading Reiser4. See www.namesys.com for a description of Reiser4. Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:01:00.0 ACPI: AC Adapter [ACAD] (on-line) Switched to high resolution mode on CPU 0 ACPI: Battery Slot [BAT1] (battery present) input: Power Button (FF) as /devices/virtual/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /devices/virtual/input/input1 ACPI: Power Button (CM) [PWRB] input: Lid Switch as /devices/virtual/input/input2 ACPI: Lid Switch [LID] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:18/LNX= VIDEO:00/input/input3 ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI Exception (thermal-0471): AE_NOT_FOUND, Invalid active threshold [0] [= 20070126] ACPI: Thermal Zone [THRM] (25 C) Real Time Clock Driver v1.12ac Linux agpgart interface v0.103 Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 6= 0 seconds). Hangcheck: Using get_cycles(). loop: module loaded 8139too Fast Ethernet driver 0.9.28 ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNK2] -> GSI 18 (level, low) -= > IRQ 18 eth0: RealTek RTL8139 at 0xffffc2000001e800, 00:0f:b0:07:dc:49, IRQ 18 eth0: Identified 8139 chip type 'RTL-8101' pata_amd 0000:00:08.0: version 0.3.10 PCI: Setting latency timer of device 0000:00:08.0 to 64 scsi0 : pata_amd scsi1 : pata_amd ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2080 irq 14 ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2088 irq 15 ata1.00: ATA-6: HTS721010G9AT00, MCZOA51A, max UDMA/100 ata1.00: 195371568 sectors, multi 16: LBA48=20 ata1: nv_mode_filter: 0x3f39f&0x3f01f->0x3f01f, BIOS=3D0x3f000 (0xc6000000)= ACPI=3D0x3f01f (20:600:0x13) ata1.00: configured for UDMA/100 ata2.00: ATAPI: HL-DT-ST DVD+RW GCA-4040N, 1.19, max MWDMA2 ata2: nv_mode_filter: 0x39f&0x39f->0x39f, BIOS=3D0x0 (0xc6000000) ACPI=3D0x= 39f (120:600:0x12) ata2.00: configured for MWDMA2 scsi 0:0:0:0: Direct-Access ATA HTS721010G9AT00 MCZO PQ: 0 ANSI: = 5 sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't suppor= t DPO or FUA sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't suppor= t DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: CD-ROM HL-DT-ST DVD+RW GCA-4040N 1.19 PQ: 0 ANSI: = 5 sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 Yenta: CardBus bridge found at 0000:02:04.0 [103c:006d] PCI: Bus 3, cardbus bridge: 0000:02:04.0 IO window: 00003000-000030ff IO window: 00003400-000034ff PREFETCH window: 50000000-53ffffff MEM window: e0400000-e07fffff Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64 Yenta: ISA IRQ mask 0x0cf8, PCI irq 19 Socket status: 30000051 Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06 pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe17fffff pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x57ffffff Yenta: CardBus bridge found at 0000:02:04.1 [103c:006d] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64 Yenta: ISA IRQ mask 0x0cf8, PCI irq 18 Socket status: 30000006 Yenta: Raising subordinate bus# of parent bus (#02) from #06 to #0a pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe17fffff pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x57ffffff PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice cpuidle: using governor ladder input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input= /input4 pccard: PCMCIA card inserted into slot 0 cs: memory probe 0x50000000-0x57ffffff: excluding 0x50000000-0x57ffffff cs: memory probe 0xe0100000-0xe17fffff: excluding 0xe0100000-0xe026ffff 0xe= 03e0000-0xe082ffff 0xe0b10000-0xe10cffff pcmcia: registering new device pcmcia0.0 scsi2 : pata_pcmcia ata3: PATA max PIO0 cmd 0x3100 ctl 0x310e irq 19 ata3.00: CFA: LEXAR ATA FLASH, V2.00, max PIO6 ata3.00: 8018640 sectors, multi 0: LBA=20 ata3.00: configured for PIO0 ata3.00: configured for PIO0 ata3: EH complete isa bounce pool size: 16 pages scsi 2:0:0:0: Direct-Access ATA LEXAR ATA FLASH V2.0 PQ: 0 ANSI: = 5 sd 2:0:0:0: [sdb] 8018640 512-byte hardware sectors (4106 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't suppo= rt DPO or FUA sd 2:0:0:0: [sdb] 8018640 512-byte hardware sectors (4106 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't suppo= rt DPO or FUA sdb: sdb1 sd 2:0:0:0: [sdb] Attached SCSI removable disk cpuidle: using governor menu TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 RPC: Registered udp transport module. RPC: Registered tcp transport module. powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3400+ processors (1 cpu co= res) (version 2.20.00) powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x2 powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x12 Marking TSC unstable due to TSC halts in idle Time: acpi_pm clocksource has been installed. swsusp: Resume From Partition /dev/sda3 PM: Checking swsusp image. PM: Resume from disk failed. registered taskstats version 1 Freeing unused kernel memory: 1124k freed reiser4: sda2: found disk format 4.0.0. sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 1:0:0:0: Attached scsi generic sg1 type 5 sd 2:0:0:0: Attached scsi generic sg2 type 0 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Clocksource tsc unstable (delta =3D 463491454 ns) ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd: block sizes: ed 80 td 96 PCI: Enabling device 0000:00:02.0 (0004 -> 0006) ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 22 (level, low) -= > IRQ 22 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller drivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001' ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: USB HC TakeOver from BIOS/SMM ohci_hcd 0000:00:02.0: created debug files ohci_hcd 0000:00:02.0: irq 22, io mem 0xe0000000 ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96 ohci_hcd 0000:00:02.0: OHCI controller state ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=3Doperational CBSR=3D3 ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=3D0 ohci_hcd 0000:00:02.0: intrstatus 0x00000044 RHSC SF ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH ohci_hcd 0000:00:02.0: hcca frame #0003 ohci_hcd 0000:00:02.0: roothub.a 01000203 POTPGT=3D1 NPS NDP=3D3(3) ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=3D0000 DR=3D0000 ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00010101 CSC PPS CCS ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS usb usb1: default language 0x0409 usb usb1: uevent usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: global over-current protection hub 1-0:1.0: power on to power good time: 2ms hub 1-0:1.0: local power source is good hub 1-0:1.0: no over-current condition exists hub 1-0:1.0: trying to enable port power on non-switchable hub drivers/usb/core/inode.c: creating file '001' usb usb1: New USB device found, idVendor=3D0000, idProduct=3D0000 usb usb1: New USB device strings: Mfr=3D3, Product=3D2, SerialNumber=3D1 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.24-rc4-mm1 ohci_hcd usb usb1: SerialNumber: 0000:00:02.0 PCI: Enabling device 0000:00:02.1 (0004 -> 0006) ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 21 (level, low) -= > IRQ 21 PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: OHCI Host Controller drivers/usb/core/inode.c: creating file '002' ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.1: USB HC TakeOver from BIOS/SMM hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0002 ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] =3D 0x00010101 CSC = PPS CCS hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s ohci_hcd 0000:00:02.1: created debug files ohci_hcd 0000:00:02.1: irq 21, io mem 0xe0001000 ohci_hcd 0000:00:02.1: OHCI controller state ohci_hcd 0000:00:02.1: OHCI 1.0, NO legacy support registers ohci_hcd 0000:00:02.1: control 0x683 RWE RWC HCFS=3Doperational CBSR=3D3 ohci_hcd 0000:00:02.1: cmdstatus 0x00000 SOC=3D0 ohci_hcd 0000:00:02.1: intrstatus 0x00000044 RHSC SF ohci_hcd 0000:00:02.1: intrenable 0x8000000a MIE RD WDH ohci_hcd 0000:00:02.1: hcca frame #0003 ohci_hcd 0000:00:02.1: roothub.a 01000203 POTPGT=3D1 NPS NDP=3D3(3) ohci_hcd 0000:00:02.1: roothub.b 00000000 PPCM=3D0000 DR=3D0000 ohci_hcd 0000:00:02.1: roothub.status 00008000 DRWE ohci_hcd 0000:00:02.1: roothub.portstatus [0] 0x00000100 PPS ohci_hcd 0000:00:02.1: roothub.portstatus [1] 0x00010101 CSC PPS CCS ohci_hcd 0000:00:02.1: roothub.portstatus [2] 0x00000100 PPS usb usb2: default language 0x0409 usb usb2: uevent usb usb2: usb_probe_device usb usb2: configuration #1 chosen from 1 choice usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: uevent hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: global over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good hub 2-0:1.0: no over-current condition exists hub 2-0:1.0: trying to enable port power on non-switchable hub hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 drivers/usb/core/inode.c: creating file '001' usb usb2: New USB device found, idVendor=3D0000, idProduct=3D0000 usb usb2: New USB device strings: Mfr=3D3, Product=3D2, SerialNumber=3D1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.24-rc4-mm1 ohci_hcd usb usb2: SerialNumber: 0000:00:02.1 ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 20 (level, low) -= > IRQ 20 PCI: Setting latency timer of device 0000:00:02.2 to 64 ehci_hcd 0000:00:02.2: EHCI Host Controller drivers/usb/core/inode.c: creating file '003' ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:02.2: reset hcs_params 0x102486 dbg=3D1 cc=3D2 pcc=3D4 !pp= c ports=3D6 ehci_hcd 0000:00:02.2: reset portroute 0 0 1 1 1 0=20 ehci_hcd 0000:00:02.2: reset hcc_params a086 caching frame 256/512/1024 par= k ehci_hcd 0000:00:02.2: park 0 ehci_hcd 0000:00:02.2: reset command 080b02 park=3D3 ithresh=3D8 period=3D1= 024 Reset HALT PCI: cache line size of 64 is not supported by device 0000:00:02.2 ehci_hcd 0000:00:02.2: supports USB remote wakeup ehci_hcd 0000:00:02.2: irq 20, io mem 0xe0004000 ehci_hcd 0000:00:02.2: reset command 080b02 park=3D3 ithresh=3D8 period=3D1= 024 Reset HALT ehci_hcd 0000:00:02.2: init command 010009 (park)=3D0 ithresh=3D1 period=3D= 256 RUN ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] =3D 0x00100103 PRSC= PPS PES CCS input: PS/2 Mouse as /devices/virtual/input/input5 usb 1-1: new full speed USB device using ohci_hcd and address 2 ohci_hcd 0000:00:02.0: urb ffff81001e1d3630 path 1 ep0in 5ec20000 cc 5 --> = status -62 ohci_hcd 0000:00:02.0: urb ffff81001e1d3630 path 1 ep0in 5ec20000 cc 5 --> = status -62 ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: default language 0x0409 usb usb3: uevent usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: uevent hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 6 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: Single TT hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns) hub 3-0:1.0: power on to power good time: 20ms hub 3-0:1.0: local power source is good hub 3-0:1.0: trying to enable port power on non-switchable hub ohci_hcd 0000:00:02.0: urb ffff81001e1d3630 path 1 ep0in 5ec20000 cc 5 --> = status -62 input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/inp= ut6 ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] =3D 0x00030100 PESC= CSC PPS hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0004 ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [1] =3D 0x00010100 CSC = PPS hub 2-0:1.0: port 2, status 0100, change 0001, 12 Mb/s drivers/usb/core/inode.c: creating file '001' usb usb3: New USB device found, idVendor=3D0000, idProduct=3D0000 usb usb3: New USB device strings: Mfr=3D3, Product=3D2, SerialNumber=3D1 usb usb3: Product: EHCI Host Controller usb usb3: Manufacturer: Linux 2.6.24-rc4-mm1 ehci_hcd usb usb3: SerialNumber: 0000:00:02.2 ACPI: PCI Interrupt Link [LACI] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LACI] -> GSI 22 (level, low) -= > IRQ 22 PCI: Setting latency timer of device 0000:00:06.0 to 64 hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0002 ohci_hcd 0000:00:02.0: GetStatus roothub.portstatus [0] =3D 0x00030100 PESC= CSC PPS hub 1-0:1.0: port 1, status 0100, change 0003, 12 Mb/s AC'97 0 analog subsections not ready hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 hub 3-0:1.0: state 7 ports 6 chg 0000 evt 0000 ehci_hcd 0000:00:02.2: GetStatus port 1 status 001803 POWER sig=3Dj CSC CON= NECT hub 3-0:1.0: port 1, status 0501, change 0001, 480 Mb/s hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 ehci_hcd 0000:00:02.2: port 1 high speed ehci_hcd 0000:00:02.2: GetStatus port 1 status 001005 POWER sig=3Dse0 PE CO= NNECT usb 3-1: new high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:02.2: port 1 high speed ehci_hcd 0000:00:02.2: GetStatus port 1 status 001005 POWER sig=3Dse0 PE CO= NNECT usb 3-1: default language 0x0409 usb 3-1: uevent usb 3-1: usb_probe_device usb 3-1: configuration #1 chosen from 1 choice usb 3-1: adding 3-1:1.0 (config #1, interface 0) usb 3-1:1.0: uevent hub 3-1:1.0: usb_probe_interface hub 3-1:1.0: usb_probe_interface - got id hub 3-1:1.0: USB hub found hub 3-1:1.0: 4 ports detected hub 3-1:1.0: standalone hub hub 3-1:1.0: ganged power switching hub 3-1:1.0: global over-current protection hub 3-1:1.0: Single TT hub 3-1:1.0: TT requires at most 32 FS bit times (2664 ns) hub 3-1:1.0: Port indicators are supported hub 3-1:1.0: power on to power good time: 100ms hub 3-1:1.0: local power source is good hub 3-1:1.0: no over-current condition exists hub 3-1:1.0: enabling power on all ports usb 3-1: link qh256-0001/ffff81001e180140 start 255 [1/0 us] drivers/usb/core/inode.c: creating file '002' usb 3-1: New USB device found, idVendor=3D05e3, idProduct=3D0608 usb 3-1: New USB device strings: Mfr=3D0, Product=3D1, SerialNumber=3D0 usb 3-1: Product: USB2.0 Hub ehci_hcd 0000:00:02.2: GetStatus port 4 status 001803 POWER sig=3Dj CSC CON= NECT hub 3-0:1.0: port 4, status 0501, change 0001, 480 Mb/s intel8x0_measure_ac97_clock: measured 50861 usecs intel8x0: measured clock 629 rejected intel8x0: clocking to 48000 ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 16 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNK5] -> GSI 16 (level, low) -= > IRQ 16 nvidiafb: Device ID: 10de0179=20 nvidiafb: CRTC0 analog not found nvidiafb: CRTC1 analog not found hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501 ehci_hcd 0000:00:02.2: port 4 full speed --> companion ehci_hcd 0000:00:02.2: GetStatus port 4 status 003001 POWER OWNER sig=3Dse0= CONNECT hub 3-0:1.0: port 4 not reset yet, waiting 50ms i2c-adapter i2c-0: unable to read EDID block. ehci_hcd 0000:00:02.2: GetStatus port 4 status 003802 POWER OWNER sig=3Dj C= SC hub 3-1:1.0: state 7 ports 4 chg 0000 evt 0000 hub 3-1:1.0: port 1, status 0101, change 0001, 12 Mb/s i2c-adapter i2c-0: unable to read EDID block. hub 3-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 hub 3-1:1.0: port 1 not reset yet, waiting 10ms usb 3-1.1: new full speed USB device using ehci_hcd and address 4 hub 3-1:1.0: port 1 not reset yet, waiting 10ms i2c-adapter i2c-0: unable to read EDID block. usb 3-1.1: ep0 maxpacket =3D 8 usb 3-1.1: default language 0x0409 usb 3-1.1: uevent usb 3-1.1: usb_probe_device usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.1: adding 3-1.1:1.0 (config #1, interface 0) usb 3-1.1:1.0: uevent hub 3-1.1:1.0: usb_probe_interface hub 3-1.1:1.0: usb_probe_interface - got id hub 3-1.1:1.0: USB hub found hub 3-1.1:1.0: 2 ports detected hub 3-1.1:1.0: compound device; port removable status: FF hub 3-1.1:1.0: ganged power switching hub 3-1.1:1.0: no over-current protection hub 3-1.1:1.0: power on to power good time: 100ms hub 3-1.1:1.0: hub controller current requirement: 100mA hub 3-1.1:1.0: 100mA bus power budget for each child hub 3-1.1:1.0: enabling power on all ports i2c-adapter i2c-1: unable to read EDID block. usb 3-1.1: link qh128-0e01/ffff81001e180280 start 127 [1/2 us] drivers/usb/core/inode.c: creating file '004' usb 3-1.1: New USB device found, idVendor=3D0451, idProduct=3D2036 usb 3-1.1: New USB device strings: Mfr=3D0, Product=3D1, SerialNumber=3D0 usb 3-1.1: Product: General Purpose USB Hub hub 3-1:1.0: port 3, status 0101, change 0001, 12 Mb/s hub 3-1:1.0: debounce: port 3: total 100ms stable 100ms status 0x101 hub 3-1:1.0: port 3 not reset yet, waiting 10ms i2c-adapter i2c-1: unable to read EDID block. usb 3-1.3: new high speed USB device using ehci_hcd and address 5 hub 3-1:1.0: port 3 not reset yet, waiting 10ms usb 3-1.3: default language 0x0409 usb 3-1.3: uevent usb 3-1.3: usb_probe_device usb 3-1.3: configuration #1 chosen from 1 choice usb 3-1.3: adding 3-1.3:1.0 (config #1, interface 0) usb 3-1.3:1.0: uevent drivers/usb/core/inode.c: creating file '005' usb 3-1.3: New USB device found, idVendor=3D0781, idProduct=3Db4b5 usb 3-1.3: New USB device strings: Mfr=3D3, Product=3D4, SerialNumber=3D5 usb 3-1.3: Product: ImageMate 14 in 1 Reader/Writer=20 usb 3-1.3: Manufacturer: SanDisk=20 usb 3-1.3: SerialNumber: 0304237855 hub 3-1:1.0: port 4, status 0101, change 0001, 12 Mb/s i2c-adapter i2c-1: unable to read EDID block. nvidiafb: CRTC 1 is currently programmed for DFP nvidiafb: Using DFP on CRTC 1 nvidiafb: Panel size is 1920 x 1200 nvidiafb: Panel is LVDS nvidiafb: MTRR set to ON fbcvt: 1920x1200@60: CVT Name - 2.304MA-R nvidiafb: PCI nVidia NV17 framebuffer (64MB @ 0xF0000000) hub 3-1:1.0: debounce: port 4: total 100ms stable 100ms status 0x101 usb 3-1.4: new full speed USB device using ehci_hcd and address 6 usb 3-1.4: ep0 maxpacket =3D 8 usb 3-1.4: default language 0x0409 usb 3-1.4: uevent usb 3-1.4: usb_probe_device usb 3-1.4: configuration #1 chosen from 1 choice usb 3-1.4: adding 3-1.4:1.0 (config #1, interface 0) usb 3-1.4:1.0: uevent hub 3-1.4:1.0: usb_probe_interface hub 3-1.4:1.0: usb_probe_interface - got id hub 3-1.4:1.0: USB hub found hub 3-1.4:1.0: 3 ports detected hub 3-1.4:1.0: compound device; port removable status: FFF hub 3-1.4:1.0: ganged power switching hub 3-1.4:1.0: global over-current protection hub 3-1.4:1.0: power on to power good time: 100ms hub 3-1.4:1.0: local power source is good hub 3-1.4:1.0: no over-current condition exists hub 3-1.4:1.0: enabling power on all ports usb 3-1.4: link qh128-0e01/ffff81001e180460 start 127 [1/2 us] drivers/usb/core/inode.c: creating file '006' usb 3-1.4: New USB device found, idVendor=3D045e, idProduct=3D0707 usb 3-1.4: New USB device strings: Mfr=3D1, Product=3D2, SerialNumber=3D0 usb 3-1.4: Product: Microsoft USB Hub usb 3-1.4: Manufacturer: Microsoft hub 3-0:1.0: state 7 ports 6 chg 0000 evt 0010 hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0004 ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [1] =3D 0x00010101 CSC = PPS CCS hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s libusual 3-1.3:1.0: usb_probe_interface libusual 3-1.3:1.0: usb_probe_interface - got id usbcore: registered new interface driver libusual Initializing USB Mass Storage driver... hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [1] =3D 0x00100103 PRSC= PPS PES CCS usb 2-2: new full speed USB device using ohci_hcd and address 2 hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend ohci_hcd 0000:00:02.0: suspend root hub ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [1] =3D 0x00100103 PRSC= PPS PES CCS usb 2-2: skipped 1 descriptor after interface usb 2-2: default language 0x0409 usb 2-2: uevent usb 2-2: usb_probe_device usb 2-2: configuration #1 chosen from 1 choice usb 2-2: adding 2-2:1.0 (config #1, interface 0) usb 2-2:1.0: uevent usb 2-2: adding 2-2:1.1 (config #1, interface 1) usb 2-2:1.1: uevent usb 2-2: adding 2-2:1.2 (config #1, interface 2) usb 2-2:1.2: uevent drivers/usb/core/inode.c: creating file '002' usb 2-2: New USB device found, idVendor=3D049f, idProduct=3D0086 usb 2-2: New USB device strings: Mfr=3D1, Product=3D2, SerialNumber=3D0 usb 2-2: Product: Bluetooth by hp usb 2-2: Manufacturer: ACTIONTEC hub 3-1:1.0: state 7 ports 4 chg 0000 evt 0010 hub 3-1.1:1.0: state 7 ports 2 chg 0000 evt 0002 hub 3-1.1:1.0: port 1, status 0301, change 0001, 1.5 Mb/s Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: HCI USB driver ver 2.9 hub 3-1.1:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 hub 3-1.1:1.0: port 1 not reset yet, waiting 10ms usb 3-1.1.1: new low speed USB device using ehci_hcd and address 7 usb 3-1.1.1: skipped 1 descriptor after interface usb 3-1.1.1: skipped 1 descriptor after interface usb 3-1.1.1: default language 0x0409 usb 3-1.1.1: uevent usb 3-1.1.1: usb_probe_device usb 3-1.1.1: configuration #1 chosen from 1 choice usb 3-1.1.1: adding 3-1.1.1:1.0 (config #1, interface 0) usb 3-1.1.1:1.0: uevent usb 3-1.1.1: adding 3-1.1.1:1.1 (config #1, interface 1) usb 3-1.1.1:1.1: uevent drivers/usb/core/inode.c: creating file '007' usb 3-1.1.1: New USB device found, idVendor=3D046d, idProduct=3Dc704 usb 3-1.1.1: New USB device strings: Mfr=3D1, Product=3D2, SerialNumber=3D3 usb 3-1.1.1: Product: USB Receiver usb 3-1.1.1: Manufacturer: Logitech usb 3-1.1.1: SerialNumber: 04E5EF hub 3-1.1:1.0: 302mA power budget left hub 3-1.4:1.0: state 7 ports 3 chg 0000 evt 0008 usb-storage 3-1.3:1.0: usb_probe_interface usb-storage 3-1.3:1.0: usb_probe_interface - got id hub 3-1.4:1.0: port 3, status 0101, change 0001, 12 Mb/s scsi3 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning hub 3-1.4:1.0: debounce: port 3: total 100ms stable 100ms status 0x101 usb 3-1.4.3: new full speed USB device using ehci_hcd and address 8 usb 3-1.4.3: ep0 maxpacket =3D 8 usb 3-1.4.3: skipped 1 descriptor after interface usb 3-1.4.3: default language 0x0409 usb 3-1.4.3: uevent usb 3-1.4.3: usb_probe_device usb 3-1.4.3: configuration #1 chosen from 1 choice usb 3-1.4.3: adding 3-1.4.3:1.0 (config #1, interface 0) usb 3-1.4.3:1.0: uevent drivers/usb/core/inode.c: creating file '008' usb 3-1.4.3: New USB device found, idVendor=3D045e, idProduct=3D0714 usb 3-1.4.3: New USB device strings: Mfr=3D1, Product=3D2, SerialNumber=3D3 usb 3-1.4.3: Product: Microsoft Wireless Laser Mouse 8000 usb 3-1.4.3: Manufacturer: Microsoft usb 3-1.4.3: SerialNumber: 00125A5F14F3 hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0004 hub 3-1.4:1.0: state 7 ports 3 chg 0000 evt 0008 usbcore: registered new interface driver usb-storage USB Mass Storage support registered. hci_usb 2-2:1.0: usb_probe_interface hci_usb 2-2:1.0: usb_probe_interface - got id hci_usb 2-2:1.2: usb_probe_interface hci_usb 2-2:1.2: usb_probe_interface - got id usbcore: registered new interface driver hci_usb usbhid 3-1.1.1:1.0: usb_probe_interface usbhid 3-1.1.1:1.0: usb_probe_interface - got id input: Logitech USB Receiver as /devices/pci0000:00/0000:00:02.2/usb3/3-1/3= -1.1/3-1.1.1/3-1.1.1:1.0/input/input7 usb 3-1.1.1: link qh8-0e01/ffff81001e180640 start 7 [1/2 us] input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:02.2-1= .1.1 usbhid 3-1.1.1:1.1: usb_probe_interface usbhid 3-1.1.1:1.1: usb_probe_interface - got id input: Logitech USB Receiver as /devices/pci0000:00/0000:00:02.2/usb3/3-1/3= -1.1/3-1.1.1/3-1.1.1:1.1/input/input8 usb 3-1.1.1: link qh8-1c02/ffff81001e1806e0 start 7 [1/2 us] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.2-1.1.= 1 usbhid 3-1.4.3:1.0: usb_probe_interface usbhid 3-1.4.3:1.0: usb_probe_interface - got id input: Microsoft Microsoft Wireless Laser Mouse 8000 as /devices/pci0000:0= 0/0000:00:02.2/usb3/3-1/3-1.4/3-1.4.3/3-1.4.3:1.0/input/input9 input: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Laser Mouse 8000]= on usb-0000:00:02.2-1.4.3 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver NET: Registered protocol family 10 ReiserFS: sda1: found reiserfs format "3.6" with standard journal ReiserFS: sda1: using ordered data mode ReiserFS: sda1: journal params: device sda1, size 8192, journal first block= 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda1: checking transaction log (sda1) usb-storage: device scan complete scsi 3:0:0:0: Direct-Access Generic STORAGE DEVICE 9339 PQ: 0 ANSI: = 0 scsi 3:0:0:1: Direct-Access Generic STORAGE DEVICE 9339 PQ: 0 ANSI: = 0 scsi 3:0:0:2: Direct-Access Generic STORAGE DEVICE 9339 PQ: 0 ANSI: = 0 scsi 3:0:0:3: Direct-Access Generic STORAGE DEVICE 9339 PQ: 0 ANSI: = 0 sd 3:0:0:0: [sdc] Attached SCSI removable disk sd 3:0:0:0: Attached scsi generic sg3 type 0 sd 3:0:0:1: [sdd] Attached SCSI removable disk sd 3:0:0:1: Attached scsi generic sg4 type 0 sd 3:0:0:2: [sde] Attached SCSI removable disk sd 3:0:0:2: Attached scsi generic sg5 type 0 sd 3:0:0:3: [sdf] Attached SCSI removable disk sd 3:0:0:3: Attached scsi generic sg6 type 0 ReiserFS: sda1: replayed 120 transactions in 1 seconds ReiserFS: sda1: Using r5 hash to sort names Adding 2843496k swap on /dev/sda3. Priority:100 extents:1 across:2843496k Bluetooth: L2CAP ver 2.9 Bluetooth: L2CAP socket layer initialized usb usb1: usb auto-resume ohci_hcd 0000:00:02.0: resume root hub hub 1-0:1.0: hub_resume hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000 Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 ohci_hcd 0000:00:02.0: auto-stop root hub hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend ohci_hcd 0000:00:02.0: suspend root hub eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1 warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) eth0: no IPv6 routers present [drm] Initialized drm 1.1.0 20060810 [drm] Detected an NV17 generation card (0x017900a5) [drm] Initialized nouveau 0.0.10 20060213 on minor 0 [drm] Used old pci detect: framebuffer loaded agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode [drm] Allocating FIFO number 0 [drm] nouveau_fifo_alloc: initialised FIFO 0 [drm] Allocating FIFO number 1 [drm] nouveau_fifo_alloc: initialised FIFO 1 usb 3-1.4.3: link qh4-3804/ffff81001e1808c0 start 3 [1/2 us] usb 3-1.4.3: unlink qh4-3804/ffff81001e1808c0 start 3 [1/2 us] ehci_hcd 0000:00:02.2: reused qh ffff81001e1808c0 schedule usb 3-1.4.3: link qh4-3804/ffff81001e1808c0 start 3 [1/2 us] Hangcheck: hangcheck value past margin! --=20 Zan Lynx --=-DWyxZK42HvbOby9x65V2 Content-Type: application/pgp-signature; name=signature.asc Content-Description: This is a digitally signed message part -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.7 (GNU/Linux) iD8DBQBHWa9AG8fHaOLTWwgRAt6YAKCSfyFj+iOadELputq6fthB7SVVOACeOw9X Ox+Ow7Dlxo+SsJZOgOpIGp0= =eAjs -----END PGP SIGNATURE----- --=-DWyxZK42HvbOby9x65V2-- -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/