Received-SPF: pass (google.com: domain of linux-kernel+bounces-6205-linux.lists.archive=gmail.com@vger.kernel.org designates 147.75.80.249 as permitted sender) client-ip=147.75.80.249;
From: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
To: Emil Renner Berthing <kernel@esmil.dk>,
	Conor Dooley <conor@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Paul Walmsley <paul.walmsley@sifive.com>,
	Palmer Dabbelt <palmer@dabbelt.com>,
	Albert Ou <aou@eecs.berkeley.edu>,
	Richard Cochran <richardcochran@gmail.com>,
	Andrew Lunn <andrew@lunn.ch>,
	Jacob Keller <jacob.e.keller@intel.com>
Cc: linux-riscv@lists.infradead.org,
	devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	netdev@vger.kernel.org,
	kernel@collabora.com,
	Emil Renner Berthing <emil.renner.berthing@canonical.com>
Subject: [PATCH v5 3/4] riscv: dts: starfive: visionfive-v1: Setup ethernet phy
Date: Wed, 20 Dec 2023 02:46:36 +0200
Message-ID: <20231220004638.2463643-4-cristian.ciocaltea@collabora.com>
In-Reply-To: <20231220004638.2463643-1-cristian.ciocaltea@collabora.com>
References: <20231220004638.2463643-1-cristian.ciocaltea@collabora.com>
Precedence: bulk
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit

The StarFive VisionFive V1 SBC uses a Motorcomm YT8521 PHY supporting
RGMII-ID, but requires manual adjustment of the RX internal delay to
work properly.

The default RX delay provided by the driver is 1.95 ns, which proves to
be too high. Applying a 50% reduction seems to mitigate the issue.

Also note this adjustment is not necessary on BeagleV Starlight SBC,
which uses a Microchip PHY.  Hence, there is no indication of a
misbehaviour on the GMAC side, but most likely the issue stems from
the Motorcomm PHY.

While at it, drop the redundant gpio include, which is already provided
by jh7100-common.dtsi.

Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 .../jh7100-starfive-visionfive-v1.dts         | 22 ++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

diff --git a/arch/riscv/boot/dts/starfive/jh7100-starfive-visionfive-v1.dts b/arch/riscv/boot/dts/starfive/jh7100-starfive-visionfive-v1.dts
index e82af72f1aaf..4e396f820660 100644
--- a/arch/riscv/boot/dts/starfive/jh7100-starfive-visionfive-v1.dts
+++ b/arch/riscv/boot/dts/starfive/jh7100-starfive-visionfive-v1.dts
@@ -6,7 +6,6 @@
 
 /dts-v1/;
 #include "jh7100-common.dtsi"
-#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "StarFive VisionFive V1";
@@ -18,3 +17,24 @@ gpio-restart {
 		priority = <224>;
 	};
 };
+
+/*
+ * The board uses a Motorcomm YT8521 PHY supporting RGMII-ID, but requires
+ * manual adjustment of the RX internal delay to work properly.  The default
+ * RX delay provided by the driver (1.95ns) is too high, but applying a 50%
+ * reduction seems to mitigate the issue.
+ *
+ * It is worth noting the adjustment is not necessary on BeagleV Starlight SBC,
+ * which uses a Microchip PHY.  Hence, most likely the Motorcomm PHY is the one
+ * responsible for the misbehaviour, not the GMAC.
+ */
+&mdio {
+	phy: ethernet-phy@0 {
+		reg = <0>;
+		rx-internal-delay-ps = <900>;
+	};
+};
+
+&gmac {
+	phy-handle = <&phy>;
+};
-- 
2.43.0