Received-SPF: pass (google.com: domain of linux-kernel+bounces-19793-linux.lists.archive=gmail.com@vger.kernel.org designates 139.178.88.99 as permitted sender) client-ip=139.178.88.99;
Received-SPF: Pass (protection.outlook.com: domain of amd.com designates
 165.204.84.17 as permitted sender) receiver=protection.outlook.com;
 client-ip=165.204.84.17; helo=SATLEXMB04.amd.com; pr=C
From: Michal Simek <michal.simek@amd.com>
To: <linux-kernel@vger.kernel.org>, <monstr@monstr.eu>,
	<michal.simek@xilinx.com>, <git@xilinx.com>
CC: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>, Conor Dooley
	<conor+dt@kernel.org>, Krzysztof Kozlowski
	<krzysztof.kozlowski+dt@linaro.org>, Rob Herring <robh+dt@kernel.org>, "open
 list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
	<devicetree@vger.kernel.org>, "moderated list:ARM/ZYNQ ARCHITECTURE"
	<linux-arm-kernel@lists.infradead.org>
Subject: [PATCH 11/14] arm64: zynqmp: Disable Tri-state for MIO38 Pin
Date: Mon, 8 Jan 2024 16:39:22 +0100
Message-ID: <9f8a0687be407a8ffad610087074e94ebc4f5982.1704728353.git.michal.simek@amd.com>
In-Reply-To: <cover.1704728353.git.michal.simek@amd.com>
References: <cover.1704728353.git.michal.simek@amd.com>
Precedence: bulk
MIME-Version: 1.0
Content-Type: text/plain; charset="UTF-8"
Content-Transfer-Encoding: 8bit
X-MS-Exchange-CrossTenant-OriginalArrivalTime: 08 Jan 2024 15:41:48.6985
 (UTC)
X-MS-Exchange-CrossTenant-Network-Message-Id: c849cb13-e993-4691-e257-08dc106053b8
X-MS-Exchange-CrossTenant-Id: 3dd8961f-e488-4e60-8e11-a82d994e183d
X-MS-Exchange-CrossTenant-OriginalAttributedTenantConnectingIp: TenantId=3dd8961f-e488-4e60-8e11-a82d994e183d;Ip=[165.204.84.17];Helo=[SATLEXMB04.amd.com]
X-MS-Exchange-CrossTenant-AuthSource:
	BL6PEPF0001AB73.namprd02.prod.outlook.com
X-MS-Exchange-CrossTenant-AuthAs: Anonymous
X-MS-Exchange-CrossTenant-FromEntityHeader: HybridOnPrem
X-MS-Exchange-Transport-CrossTenantHeadersStamped: MN0PR12MB5809

From: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>

gpio38 is used in SOM's kv260 to reset the Ethernet PHY.
At present, HW reset is not working properly as Tri-state 
is enabled for MIO38, causing inappropriate PHY register reads.

Disabled Tri-state for MIO38 to make HW reset work.

Tri-state disable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7a3 00000540

Tri-state enable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7e3 00000540

Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
---

 .../boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso | 25 +++++++++++++++++++
 .../boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso | 25 +++++++++++++++++++
 2 files changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
index b7b94254cc09..585b5845a1f4 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
@@ -169,6 +169,25 @@ phy0: ethernet-phy@1 {
 &pinctrl0 {
 	status = "okay";
 
+	pinctrl_gpio0_default: gpio0-default {
+                conf {
+                        groups = "gpio0_38_grp";
+                        bias-pull-up;
+                        power-source = <IO_STANDARD_LVCMOS18>;
+                };
+
+                mux {
+                        groups = "gpio0_38_grp";
+                        function = "gpio0";
+                };
+
+                conf-tx {
+                        pins = "MIO38";
+                        bias-disable;
+                        output-enable;
+                };
+        };
+
 	pinctrl_uart1_default: uart1-default {
 		conf {
 			groups = "uart1_9_grp";
@@ -324,6 +343,12 @@ mux {
 	};
 };
 
+&gpio {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_gpio0_default>;
+};
+
 &uart1 {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
index 1446c2b19de7..037f0941ba0b 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
@@ -152,6 +152,25 @@ phy0: ethernet-phy@1 {
 &pinctrl0 {
 	status = "okay";
 
+	pinctrl_gpio0_default: gpio0-default {
+		conf {
+			groups = "gpio0_38_grp";
+			bias-pull-up;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "gpio0_38_grp";
+			function = "gpio0";
+		};
+
+		conf-tx {
+			pins = "MIO38";
+			bias-disable;
+			output-enable;
+		};
+	};
+
 	pinctrl_uart1_default: uart1-default {
 		conf {
 			groups = "uart1_9_grp";
@@ -307,6 +326,12 @@ mux {
 	};
 };
 
+&gpio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio0_default>;
+};
+
 &uart1 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.36.1