Received-SPF: pass (google.com: domain of linux-kernel+bounces-73352-linux.lists.archive=gmail.com@vger.kernel.org designates 2604:1380:40f1:3f00::1 as permitted sender) client-ip=2604:1380:40f1:3f00::1;
From: sabiya.d@mistralsolutions.com
To: nm@ti.com,
	vigneshr@ti.com,
	kristo@kernel.org,
	robh+dt@kernel.org,
	krzysztof.kozlowski+dt@linaro.org,
	linus.walleij@linaro.org
Cc: devicetree@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org,
	u-kumar1@ti.com,
	sabiya.d@mistralsolutions.com,
	Dasnavis Sabiya <sabiya.d@ti.com>
Subject: [PATCH V3 2/2] arm64: dts: ti: k3-am69-sk: Add support for OSPI flash
Date: Tue, 20 Feb 2024 21:55:27 +0530
Message-Id: <20240220162527.663394-3-sabiya.d@ti.com>
In-Reply-To: <20240220162527.663394-1-sabiya.d@ti.com>
References: <20240220162527.663394-1-sabiya.d@ti.com>
Precedence: bulk
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit

From: Dasnavis Sabiya <sabiya.d@ti.com>

AM69 SK has S28HS512T OSPI flash connected to MCU OSPI0.
Enable support for the same. Also describe the partition
information according to the offsets in the bootloader.

Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am69-sk.dts | 81 +++++++++++++++++++++++++++
 1 file changed, 81 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
index 7afdfbbe956d..50de2a448a3a 100644
--- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
@@ -486,6 +486,25 @@ J784S4_IOPAD(0x09C, PIN_OUTPUT, 0) /* (AF35) MCAN7_TX */
 
 };
 
+&wkup_pmx0 {
+	bootph-all;
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
+			J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
+			J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
+			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
+			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
+			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
+			J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
+			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
+			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
+			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
+			J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
+		>;
+	};
+};
+
 &wkup_pmx2 {
 	bootph-all;
 	pmic_irq_pins_default: pmic-irq-default-pins {
@@ -1122,3 +1141,65 @@ &main_mcan7 {
 	pinctrl-0 = <&main_mcan7_pins_default>;
 	phys = <&transceiver4>;
 };
+
+&ospi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+
+		partitions {
+			bootph-all;
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "ospi.tiboot3";
+				reg = <0x0 0x100000>;
+			};
+
+			partition@100000 {
+				label = "ospi.tispl";
+				reg = <0x100000 0x200000>;
+			};
+
+			partition@300000 {
+				label = "ospi.u-boot";
+				reg = <0x300000 0x400000>;
+			};
+
+			partition@700000 {
+				label = "ospi.env";
+				reg = <0x700000 0x40000>;
+			};
+
+			partition@740000 {
+				label = "ospi.env.backup";
+				reg = <0x740000 0x40000>;
+			};
+
+			partition@800000 {
+				label = "ospi.rootfs";
+				reg = <0x800000 0x37c0000>;
+			};
+
+			partition@3fc0000 {
+				bootph-pre-ram;
+				label = "ospi.phypattern";
+				reg = <0x3fc0000 0x40000>;
+			};
+		};
+	};
+};
-- 
2.34.1