Received-SPF: pass (google.com: domain of linux-kernel+bounces-89921-linux.lists.archive=gmail.com@vger.kernel.org designates 2604:1380:40f1:3f00::1 as permitted sender) client-ip=2604:1380:40f1:3f00::1;
From: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Date: Sun, 03 Mar 2024 22:54:22 +0100
Subject: [PATCH v3 3/3] iio: humidity: hdc3020: add reset management
Precedence: bulk
MIME-Version: 1.0
Content-Type: text/plain; charset="utf-8"
Content-Transfer-Encoding: 7bit
Message-Id: <20240303-hdc3020-pm-v3-3-48bc02b5241b@gmail.com>
References: <20240303-hdc3020-pm-v3-0-48bc02b5241b@gmail.com>
In-Reply-To: <20240303-hdc3020-pm-v3-0-48bc02b5241b@gmail.com>
To: Jonathan Cameron <jic23@kernel.org>, 
 Lars-Peter Clausen <lars@metafoo.de>, Li peiyu <579lpy@gmail.com>, 
 Rob Herring <robh+dt@kernel.org>, 
 Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, 
 Conor Dooley <conor+dt@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>, 
 linux-kernel@vger.kernel.org, linux-iio@vger.kernel.org, 
 devicetree@vger.kernel.org, 
 Javier Carrasco <javier.carrasco.cruz@gmail.com>

The HDC3020 provides an active low reset signal that must be handled if
connected. Asserting this signal turns the device into Trigger-on Demand
measurement mode, reducing its power consumption when no measurements
are required like in low-power modes.

According to the datasheet, the longest "Reset Ready" is 3 ms, which is
only taken into account if the reset signal is defined.

Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
---
 drivers/iio/humidity/hdc3020.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/iio/humidity/hdc3020.c b/drivers/iio/humidity/hdc3020.c
index 7f93024b850c..cdc4789213ba 100644
--- a/drivers/iio/humidity/hdc3020.c
+++ b/drivers/iio/humidity/hdc3020.c
@@ -15,6 +15,7 @@
 #include <linux/cleanup.h>
 #include <linux/crc8.h>
 #include <linux/delay.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/init.h>
 #include <linux/interrupt.h>
@@ -70,6 +71,7 @@
 
 struct hdc3020_data {
 	struct i2c_client *client;
+	struct gpio_desc *reset_gpio;
 	struct regulator *vdd_supply;
 	/*
 	 * Ensure that the sensor configuration (currently only heater is
@@ -558,6 +560,9 @@ static int hdc3020_power_off(struct hdc3020_data *data)
 {
 	hdc3020_exec_cmd(data, HDC3020_EXIT_AUTO);
 
+	if (data->reset_gpio)
+		gpiod_set_value_cansleep(data->reset_gpio, 1);
+
 	return regulator_disable(data->vdd_supply);
 }
 
@@ -571,6 +576,11 @@ static int hdc3020_power_on(struct hdc3020_data *data)
 
 	fsleep(5000);
 
+	if (data->reset_gpio) {
+		gpiod_set_value_cansleep(data->reset_gpio, 0);
+		fsleep(3000);
+	}
+
 	if (data->client->irq) {
 		/*
 		 * The alert output is activated by default upon power up,
@@ -627,6 +637,12 @@ static int hdc3020_probe(struct i2c_client *client)
 		return dev_err_probe(&client->dev, PTR_ERR(data->vdd_supply),
 				     "Unable to get VDD regulator\n");
 
+	data->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
+						   GPIOD_OUT_HIGH);
+	if (IS_ERR(data->reset_gpio))
+		return dev_err_probe(&client->dev, PTR_ERR(data->reset_gpio),
+				     "Cannot get reset GPIO\n");
+
 	ret = hdc3020_power_on(data);
 	if (ret)
 		return dev_err_probe(&client->dev, ret, "Power on failed\n");

-- 
2.40.1