Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
From:   "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
To:     johan@kernel.org
Cc:     gregkh@linuxfoundation.org, linux-usb@vger.kernel.org,
        linux-kernel@vger.kernel.org,
        "Ji-Ze Hong (Peter Hong)" <hpeter+linux_kernel@gmail.com>
Subject: [PATCH V1 2/4] usb: serial: f81534: add auto RTS direction support
Date:   Thu, 16 Nov 2017 15:46:07 +0800
Message-Id: <1510818369-10323-2-git-send-email-hpeter+linux_kernel@gmail.com>
In-Reply-To: <1510818369-10323-1-git-send-email-hpeter+linux_kernel@gmail.com>
References: <1510818369-10323-1-git-send-email-hpeter+linux_kernel@gmail.com>
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
	0: F81534_PORT_CONF_RS232.
	1: F81534_PORT_CONF_RS485.
	2: value error, default to F81534_PORT_CONF_RS232.
	3: F81534_PORT_CONF_RS485_INVERT.

F81532/534 Clock register (offset +08h)

Bit0:	UART Enable (always on)
Bit2-1:	Clock source selector
			00: 1.846MHz.
			01: 18.46MHz.
			10: 24MHz.
			11: 14.77MHz.
Bit4:	Auto direction(RTS) control (RTS pin Low when TX)
Bit5:	Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81534.c | 54 +++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 52 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 76c676ef5f0d..b2d10309c335 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -102,11 +102,16 @@
 
 #define F81534_DEFAULT_BAUD_RATE	9600
 
+#define F81534_PORT_CONF_RS232		0
+#define F81534_PORT_CONF_RS485		BIT(0)
+#define F81534_PORT_CONF_RS485_INVERT	(BIT(0) | BIT(1))
 #define F81534_PORT_CONF_DISABLE_PORT	BIT(3)
 #define F81534_PORT_CONF_NOT_EXIST_PORT	BIT(7)
 #define F81534_PORT_UNAVAILABLE		\
 	(F81534_PORT_CONF_DISABLE_PORT | F81534_PORT_CONF_NOT_EXIST_PORT)
 
+#define F81534_UART_MODE_MASK		(BIT(0) | BIT(1))
+
 #define F81534_1X_RXTRIGGER		0xc3
 #define F81534_8X_RXTRIGGER		0xcf
 
@@ -119,6 +124,8 @@
  *			01: 18.46MHz.
  *			10: 24MHz.
  *			11: 14.77MHz.
+ * Bit4:	Auto direction(RTS) control (RTS pin Low when TX)
+ * Bit5:	Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
  */
 
 #define F81534_CLK_1_846_MHZ		BIT(0)
@@ -126,6 +133,9 @@
 #define F81534_CLK_24_MHZ		(BIT(0) | BIT(2))
 #define F81534_CLK_14_77_MHZ		(BIT(0) | BIT(1) | BIT(2))
 
+#define F81534_CLK_RS485_MODE		BIT(4)
+#define F81534_CLK_RS485_INVERT		BIT(5)
+
 static const struct usb_device_id f81534_id_table[] = {
 	{ USB_DEVICE(FINTEK_VENDOR_ID_1, FINTEK_DEVICE_ID) },
 	{ USB_DEVICE(FINTEK_VENDOR_ID_2, FINTEK_DEVICE_ID) },
@@ -485,16 +495,20 @@ static int f81534_set_port_config(struct usb_serial_port *port,
 		struct tty_struct *tty, u32 baudrate, u32 old_baudrate, u8 lcr)
 {
 	struct f81534_port_private *port_priv = usb_get_serial_port_data(port);
+	struct f81534_serial_private *serial_priv;
 	u32 divisor;
 	int status;
 	int idx;
 	u8 value;
+	u8 tmp;
 	static u32 const baudrate_table[] = {115200, 921600, 1152000,
 			1500000};
 	static u8 const clock_table[] = {F81534_CLK_1_846_MHZ,
 			F81534_CLK_14_77_MHZ, F81534_CLK_18_46_MHZ,
 			F81534_CLK_24_MHZ};
 
+	serial_priv = usb_get_serial_data(port->serial);
+
 	do {
 		for (idx = 0; idx < ARRAY_SIZE(baudrate_table); ++idx) {
 			if (baudrate <= baudrate_table[idx] &&
@@ -520,8 +534,25 @@ static int f81534_set_port_config(struct usb_serial_port *port,
 	} while (1);
 
 	port_priv->baud_base = baudrate_table[idx];
-	status = f81534_set_port_register(port, F81534_CLOCK_REG,
-			clock_table[idx]);
+	tmp = serial_priv->conf_data[port_priv->phy_num];
+
+	switch (tmp & F81534_UART_MODE_MASK) {
+	case F81534_PORT_CONF_RS485_INVERT:
+		value = F81534_CLK_RS485_MODE | F81534_CLK_RS485_INVERT;
+		break;
+	case F81534_PORT_CONF_RS485:
+		value = F81534_CLK_RS485_MODE;
+		break;
+
+	default:
+		/* fall through, default RS232 Mode */
+	case F81534_PORT_CONF_RS232:
+		value = 0;
+		break;
+	}
+
+	value |= clock_table[idx];
+	status = f81534_set_port_register(port, F81534_CLOCK_REG, value);
 	if (status) {
 		dev_err(&port->dev, "CLOCK_REG setting failed\n");
 		return status;
@@ -1270,9 +1301,12 @@ static void f81534_lsr_worker(struct work_struct *work)
 
 static int f81534_port_probe(struct usb_serial_port *port)
 {
+	struct f81534_serial_private *serial_priv;
 	struct f81534_port_private *port_priv;
 	int ret;
+	u8 value;
 
+	serial_priv = usb_get_serial_data(port->serial);
 	port_priv = devm_kzalloc(&port->dev, sizeof(*port_priv), GFP_KERNEL);
 	if (!port_priv)
 		return -ENOMEM;
@@ -1304,6 +1338,22 @@ static int f81534_port_probe(struct usb_serial_port *port)
 	if (ret)
 		return ret;
 
+	value = serial_priv->conf_data[port_priv->phy_num];
+	switch (value & F81534_UART_MODE_MASK) {
+	case F81534_PORT_CONF_RS485_INVERT:
+		dev_info(&port->dev, "RS485 invert mode.\n");
+		break;
+	case F81534_PORT_CONF_RS485:
+		dev_info(&port->dev, "RS485 mode.\n");
+		break;
+
+	default:
+		/* fall through, default RS232 Mode */
+	case F81534_PORT_CONF_RS232:
+		dev_info(&port->dev, "RS232 mode.\n");
+		break;
+	}
+
 	return 0;
 }
 
-- 
2.7.4


From 1584205627008771636@xxx Thu Nov 16 07:10:18 +0000 2017
X-GM-THRID: 1584144460908342567
X-Gmail-Labels: Inbox,Category Forums,HistoricalUnread