Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1762122AbYHERw7 (ORCPT ); Tue, 5 Aug 2008 13:52:59 -0400 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S1757478AbYHERwb (ORCPT ); Tue, 5 Aug 2008 13:52:31 -0400 Received: from ottawa-hs-64-26-148-84.d-ip.magma.ca ([64.26.148.84]:33989 "EHLO gonzo.int.wil.cx" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1755093AbYHERw2 (ORCPT ); Tue, 5 Aug 2008 13:52:28 -0400 X-Greylist: delayed 900 seconds by postgrey-1.27 at vger.kernel.org; Tue, 05 Aug 2008 13:52:28 EDT From: Matthew Wilcox To: linux-kernel@vger.kernel.org, linux-ide@vger.kernel.org Cc: jgarzik@pobox.com, Matt_Domsch@dell.com, Matthew Wilcox Subject: [PATCH] ata: Define new commands from ATA8 Date: Tue, 5 Aug 2008 13:26:46 -0400 Message-Id: <1217957207-23116-2-git-send-email-matthew@wil.cx> X-Mailer: git-send-email 1.5.6.3 In-Reply-To: <1217957207-23116-1-git-send-email-matthew@wil.cx> References: <1217957207-23116-1-git-send-email-matthew@wil.cx> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 5179 Lines: 148 From: Matthew Wilcox Later patches require knowledge of some commands which aren't currently defined. While I'm at it, add all the commands that are in ATA8 and reorder the existing commands to be in the same order as ATA8. Signed-off-by: Matthew Wilcox --- include/linux/ata.h | 97 ++++++++++++++++++++++++++++++++++---------------- 1 files changed, 66 insertions(+), 31 deletions(-) diff --git a/include/linux/ata.h b/include/linux/ata.h index 1c622e2..3815431 100644 --- a/include/linux/ata.h +++ b/include/linux/ata.h @@ -149,58 +149,93 @@ enum { ATA_REG_IRQ = ATA_REG_NSECT, /* ATA device commands */ - ATA_CMD_DEV_RESET = 0x08, /* ATAPI device reset */ + ATA_CMD_CFA_ERASE_SECTORS = 0xC0, + ATA_CMD_CFA_REQUEST_EXT_ERROR = 0x03, + ATA_CMD_CFA_TRANSLATE_SECTOR = 0x87, + ATA_CMD_CFA_WRITE_MULTI_WITHOUT_ERASE = 0xCD, + ATA_CMD_CFA_WRITE_SECTORS_WITHOUT_ERASE = 0x38, + ATA_CMD_CHK_MEDIA_CARD_TYPE = 0xD1, ATA_CMD_CHK_POWER = 0xE5, /* check power mode */ - ATA_CMD_STANDBY = 0xE2, /* place in standby power mode */ - ATA_CMD_IDLE = 0xE3, /* place in idle power mode */ + ATA_CMD_CONFIG_STREAM = 0x51, + ATA_CMD_CONF_OVERLAY = 0xB1, + ATA_CMD_DEV_RESET = 0x08, /* ATAPI device reset */ + ATA_CMD_DLOAD_MCODE = 0x92, ATA_CMD_EDD = 0x90, /* execute device diagnostic */ ATA_CMD_FLUSH = 0xE7, ATA_CMD_FLUSH_EXT = 0xEA, ATA_CMD_ID_ATA = 0xEC, ATA_CMD_ID_ATAPI = 0xA1, - ATA_CMD_READ = 0xC8, - ATA_CMD_READ_EXT = 0x25, - ATA_CMD_WRITE = 0xCA, - ATA_CMD_WRITE_EXT = 0x35, - ATA_CMD_WRITE_FUA_EXT = 0x3D, + ATA_CMD_IDLE = 0xE3, /* place in idle power mode */ + ATA_CMD_IDLEIMMEDIATE = 0xE1, + ATA_CMD_NVCACHE = 0xB6, + ATA_CMD_NOP = 0x00, + ATA_CMD_PACKET = 0xA0, + ATA_CMD_PMP_READ = 0xE4, /* aka READ BUFFER */ + ATA_CMD_READ = 0xC8, /* aka READ DMA */ + ATA_CMD_READ_EXT = 0x25, /* aka READ DMA EXT */ + ATA_CMD_READ_QUEUED = 0xC7, + ATA_CMD_READ_QUEUED_EXT = 0x26, ATA_CMD_FPDMA_READ = 0x60, - ATA_CMD_FPDMA_WRITE = 0x61, - ATA_CMD_PIO_READ = 0x20, - ATA_CMD_PIO_READ_EXT = 0x24, - ATA_CMD_PIO_WRITE = 0x30, - ATA_CMD_PIO_WRITE_EXT = 0x34, + ATA_CMD_READ_LOG_EXT = 0x2F, + ATA_CMD_READ_LOG_DMA_EXT= 0x47, ATA_CMD_READ_MULTI = 0xC4, ATA_CMD_READ_MULTI_EXT = 0x29, - ATA_CMD_WRITE_MULTI = 0xC5, - ATA_CMD_WRITE_MULTI_EXT = 0x39, - ATA_CMD_WRITE_MULTI_FUA_EXT = 0xCE, - ATA_CMD_SET_FEATURES = 0xEF, - ATA_CMD_SET_MULTI = 0xC6, - ATA_CMD_PACKET = 0xA0, - ATA_CMD_VERIFY = 0x40, - ATA_CMD_VERIFY_EXT = 0x42, - ATA_CMD_STANDBYNOW1 = 0xE0, - ATA_CMD_IDLEIMMEDIATE = 0xE1, - ATA_CMD_SLEEP = 0xE6, - ATA_CMD_INIT_DEV_PARAMS = 0x91, ATA_CMD_READ_NATIVE_MAX = 0xF8, ATA_CMD_READ_NATIVE_MAX_EXT = 0x27, + ATA_CMD_PIO_READ = 0x20, /* aka READ SECTOR(S) */ + ATA_CMD_PIO_READ_EXT = 0x24, /* aka READ SECTOR(S) EXT */ + ATA_CMD_READ_STREAM_DMA_EXT = 0x2A, + ATA_CMD_READ_STREAM_EXT = 0x2B, + ATA_CMD_VERIFY = 0x40, /* aka READ VERIFY SECTOR(S) */ + ATA_CMD_VERIFY_EXT = 0x42, /* aka READ VERIFY SECTOR(S) EXT */ + ATA_CMD_SEC_DISABLE_PASSWORD = 0xF6, + ATA_CMD_SEC_ERASE_PREPARE = 0xF3, + ATA_CMD_SEC_ERASE_UNIT = 0xF4, + ATA_CMD_SEC_FREEZE_LOCK = 0xF5, + ATA_CMD_SEC_SET_PASSWORD = 0xF1, + ATA_CMD_SEC_UNLOCK = 0xF2, + ATA_CMD_SERVICE = 0xA2, + ATA_CMD_SET_FEATURES = 0xEF, ATA_CMD_SET_MAX = 0xF9, ATA_CMD_SET_MAX_EXT = 0x37, - ATA_CMD_READ_LOG_EXT = 0x2f, - ATA_CMD_PMP_READ = 0xE4, - ATA_CMD_PMP_WRITE = 0xE8, - ATA_CMD_CONF_OVERLAY = 0xB1, - ATA_CMD_SEC_FREEZE_LOCK = 0xF5, + ATA_CMD_SET_MULTI = 0xC6, + ATA_CMD_SLEEP = 0xE6, + ATA_CMD_SMART = 0xB0, + ATA_CMD_STANDBY = 0xE2, /* place in standby power mode */ + ATA_CMD_STANDBYNOW1 = 0xE0, + ATA_CMD_TRUSTED_NON_DATA = 0x5B, + ATA_CMD_TRUSTED_RECEIVE = 0x5C, + ATA_CMD_TRUSTED_RECEIVE_DMA = 0x5D, + ATA_CMD_TRUSTED_SEND = 0x5E, + ATA_CMD_TRUSTED_SEND_DMA = 0x5F, + ATA_CMD_PMP_WRITE = 0xE8, /* aka WRITE BUFFER */ + ATA_CMD_WRITE = 0xCA, /* aka WRITE DMA */ + ATA_CMD_WRITE_EXT = 0x35, /* aka WRITE DMA EXT */ + ATA_CMD_WRITE_FUA_EXT = 0x3D, /* aka WRITE DMA FUA EXT */ + ATA_CMD_WRITE_DMA_QUEUED = 0xCC, + ATA_CMD_WRITE_DMA_QUEUED_EXT = 0x36, + ATA_CMD_WRITE_DMA_QUEUED_FUA_EXT = 0x3E, + ATA_CMD_FPDMA_WRITE = 0x61, /* aka WRITE FPDMA QUEUED */ + ATA_CMD_WRITE_LOG_EXT = 0x3F, + ATA_CMD_WRITE_LOG_DMA_EXT = 0x57, + ATA_CMD_WRITE_MULTI = 0xC5, + ATA_CMD_WRITE_MULTI_EXT = 0x39, + ATA_CMD_WRITE_MULTI_FUA_EXT = 0xCE, + ATA_CMD_PIO_WRITE = 0x30, /* aka WRITE SECTOR(S) */ + ATA_CMD_PIO_WRITE_EXT = 0x34, /* aka WRITE SECTOR(S) EXT */ + ATA_CMD_WRITE_STREAM_DMA_EXT = 0x3A, + ATA_CMD_WRITE_STREAM_EXT = 0x3B, + ATA_CMD_WRITE_UNCORRECTABLE_EXT = 0x45, /* READ_LOG_EXT pages */ ATA_LOG_SATA_NCQ = 0x10, - /* READ/WRITE LONG (obsolete) */ + /* Obsolete */ ATA_CMD_READ_LONG = 0x22, ATA_CMD_READ_LONG_ONCE = 0x23, ATA_CMD_WRITE_LONG = 0x32, ATA_CMD_WRITE_LONG_ONCE = 0x33, + ATA_CMD_INIT_DEV_PARAMS = 0x91, /* SETFEATURES stuff */ SETFEATURES_XFER = 0x03, -- 1.5.6.3 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/