Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id ; Sun, 24 Mar 2002 00:29:47 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id ; Sun, 24 Mar 2002 00:29:37 -0500 Received: from [206.58.238.200] ([206.58.238.200]:64386 "EHLO portland.puremagic.com") by vger.kernel.org with ESMTP id ; Sun, 24 Mar 2002 00:29:27 -0500 Date: Sat, 23 Mar 2002 21:29:19 -0800 (PST) From: Brad Roberts To: Subject: partition detection failure between 2.4.19-pre2 and pre3 Message-ID: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org (not on the list, I read it via a list archive due to traffic, so please cc me on all replies) Starting with 2.4.19-pre3 (and continuing for -pre4 and every post-pre2 ac kernel I've tried) bootup hangs during partition detection: 2.4.19-pre2 output: Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PDC20265: IDE controller on PCI bus 00 dev 30 PCI: Found IRQ 5 for device 00:06.0 PCI: Sharing IRQ 5 with 00:10.0 PCI: Sharing IRQ 5 with 00:11.2 PCI: Sharing IRQ 5 with 00:11.3 PCI: Sharing IRQ 5 with 00:11.4 PDC20265: chipset revision 2 PDC20265: not 100% native mode: will probe irqs later PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode. ide2: BM-DMA at 0xb400-0xb407, BIOS settings: hde:DMA, hdf:pio ide3: BM-DMA at 0xb408-0xb40f, BIOS settings: hdg:DMA, hdh:pio VP_IDE: IDE controller on PCI bus 00 dev 89 PCI: Found IRQ 11 for device 00:11.1 PCI: Sharing IRQ 11 with 01:00.0 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1 ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:DMA, hdd:pio hda: Maxtor 98196H8, ATA DISK drive hdc: 52X CD-ROM, ATAPI CD/DVD-ROM drive hde: Maxtor 4D060H3, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide2 at 0xd800-0xd807,0xd402 on irq 5 hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=9964/255/63, UDMA(100) hde: 120069936 sectors (61476 MB) w/2048KiB Cache, CHS=119117/16/63, UDMA(100) hdc: ATAPI 52X CD-ROM drive, 128kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 Partition check: hda: hda1 hda2 < hda5 > hda3 hda4 hde: hde1 The pre-3 output stops right after: Partition check: hda: hda1 hda2 < hda5 > hda3 hda4 hde: Ie, it never detects any partitions on hde. The motherboard is an A7V266-E asus motherboard. Suggestions? I started looking through the changes between pre2 and pre3, but the ide subsystem got overhauled reasonably thoroughly in pre3. Thanks, Brad - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/