Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1755906Ab1BQA6W (ORCPT ); Wed, 16 Feb 2011 19:58:22 -0500 Received: from xes-mad.com ([216.165.139.218]:52225 "EHLO xes-mad.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1755878Ab1BQA6I (ORCPT ); Wed, 16 Feb 2011 19:58:08 -0500 From: Peter Tyser To: linux-kernel@vger.kernel.org Cc: Peter Tyser , Alek Du , Samuel Ortiz , David Brownell , Eric Miao , Uwe Kleine-K?nig , Mark Brown , Joe Perches , Alan Cox , Grant Likely Subject: [PATCH v2 4/4] gpio: Add support for Intel ICHx/3100/Series[56] GPIO Date: Wed, 16 Feb 2011 18:56:56 -0600 Message-Id: <1297904216-15219-4-git-send-email-ptyser@xes-inc.com> X-Mailer: git-send-email 1.7.0.4 In-Reply-To: <1297904216-15219-1-git-send-email-ptyser@xes-inc.com> References: <1297904216-15219-1-git-send-email-ptyser@xes-inc.com> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 21208 Lines: 645 This driver works on many Intel chipsets, including the ICH6, ICH7, ICH8, ICH9, ICH10, 3100, Series 5/3400 (Ibex Peak), Series 6/C200 (Cougar Point). Additional Intel chipsets should be easily supported if needed, eg the ICH1-5, EP80579, etc. Tested on a QM57 (Ibex Peak) and 3100. Cc: Alek Du Cc: Samuel Ortiz Cc: David Brownell Cc: Eric Miao Cc: Uwe Kleine-K?nig Cc: Mark Brown Cc: Joe Perches Cc: Alan Cox Cc: Grant Likely Signed-off-by: Peter Tyser --- Changes since v1: - Fixed grammar in Kconfig menu entry MAINTAINERS | 5 + drivers/gpio/Kconfig | 11 + drivers/gpio/Makefile | 1 + drivers/gpio/ichx_gpio.c | 551 ++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 568 insertions(+), 0 deletions(-) create mode 100644 drivers/gpio/ichx_gpio.c diff --git a/MAINTAINERS b/MAINTAINERS index 4837907..1778396 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3108,6 +3108,11 @@ W: http://www.developer.ibm.com/welcome/netfinity/serveraid.html S: Supported F: drivers/scsi/ips.* +ICHX GPIO DRIVER +M: Peter Tyser +S: Maintained +F: drivers/gpio/ichx_gpio.c + IDE SUBSYSTEM M: "David S. Miller" L: linux-ide@vger.kernel.org diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 664660e..13b7998 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -319,6 +319,17 @@ config GPIO_BT8XX If unsure, say N. +config GPIO_ICHX + tristate "Intel ICHx GPIO" + depends on PCI && GPIOLIB && X86 + help + Say yes here to support the GPIO functionality of a number of Intel + ICH-based chipsets. Currently supported devices: ICH6, ICH7, ICH8 + ICH9, ICH10, Series 5/3400 (eg Ibex Peak), Series 6/C200 (eg + Cougar Point), and 3100. + + If unsure, say N. + config GPIO_LANGWELL bool "Intel Langwell/Penwell GPIO support" depends on PCI diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 3351cf8..8900bc6 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -11,6 +11,7 @@ obj-$(CONFIG_GPIOLIB) += gpiolib.o obj-$(CONFIG_GPIO_ADP5520) += adp5520-gpio.o obj-$(CONFIG_GPIO_ADP5588) += adp5588-gpio.o obj-$(CONFIG_GPIO_BASIC_MMIO) += basic_mmio_gpio.o +obj-$(CONFIG_GPIO_ICHX) += ichx_gpio.o obj-$(CONFIG_GPIO_LANGWELL) += langwell_gpio.o obj-$(CONFIG_GPIO_MAX730X) += max730x.o obj-$(CONFIG_GPIO_MAX7300) += max7300.o diff --git a/drivers/gpio/ichx_gpio.c b/drivers/gpio/ichx_gpio.c new file mode 100644 index 0000000..88f02dc --- /dev/null +++ b/drivers/gpio/ichx_gpio.c @@ -0,0 +1,551 @@ +/* + * Intel ICH6-10, Series 5 and 6 GPIO driver + * + * Copyright (C) 2010 Extreme Engineering Solutions. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include +#include +#include +#include + +#define DRV_NAME "ichx_gpio" + +/* PCI config register offsets into LPC I/F - D31:F0 */ +#define PCI_ICHX_ACPI_BAR 0x40 +#define PCI_ICHX_GPIO_BAR 0x48 +#define PCI_ICHX_GPIO_CTRL 0x4C + +/* + * GPIO register offsets in GPIO I/O space. + * Each chunk of 32 GPIOs is manipulated via its own USE_SELx, IO_SELx, and + * LVLx registers. Logic in the read/write functions takes a register and + * an absolute bit number and determines the proper register offset and bit + * number in that register. For example, to read the value of GPIO bit 50 + * the code would access offset ichx_regs[2(=GPIO_LVL)][1(=50/32)], + * bit 18 (50%32). + */ +enum GPIO_REG { + GPIO_USE_SEL = 0, + GPIO_IO_SEL, + GPIO_LVL, +}; +static const u8 ichx_regs[3][3] = { + {0x00, 0x30, 0x40}, /* USE_SEL[1-3] offsets */ + {0x04, 0x34, 0x44}, /* IO_SEL[1-3] offsets */ + {0x0c, 0x38, 0x48}, /* LVL[1-3] offsets */ +}; + +#define ICHX_GPIO_WRITE(val, reg) outl(val, (reg) + ichx_priv.gpio_base) +#define ICHX_GPIO_READ(reg) inl((reg) + ichx_priv.gpio_base) +#define ICHX_PM_WRITE(val, reg) outl(val, (reg) + ichx_priv.pm_base) +#define ICHX_PM_READ(reg) inl((reg) + ichx_priv.pm_base) + +/* Convenient wrapper to make our PCI ID table */ +#define ICHX_GPIO_PCI_DEVICE(dev, data) \ + .vendor = PCI_VENDOR_ID_INTEL, \ + .device = dev, \ + .subvendor = PCI_ANY_ID, \ + .subdevice = PCI_ANY_ID, \ + .class = 0, \ + .class_mask = 0, \ + .driver_data = (ulong)data + +struct ichx_desc { + /* Max GPIO pins the chipset can have */ + uint ngpio; + + /* The offset of GPE0_STS in the PM IO region, 0 if unneeded */ + uint gpe0_sts_ofs; + + /* USE_SEL is bogus on some chipsets, eg 3100 */ + u32 use_sel_ignore[3]; + + /* Some chipsets have quirks, let these use their own request/get */ + int (*request)(struct gpio_chip *chip, unsigned offset); + int (*get)(struct gpio_chip *chip, unsigned offset); +}; + +static struct { + spinlock_t lock; + struct platform_device *dev; + struct pci_dev *pdev; + struct gpio_chip chip; + unsigned long gpio_base;/* GPIO IO base */ + unsigned long pm_base; /* Power Mangagment IO base */ + struct ichx_desc *desc; /* Pointer to chipset-specific description */ + u32 orig_gpio_ctrl; /* Orig CTRL value, used to restore on exit */ +} ichx_priv; + +static struct platform_device *ichx_gpio_platform_device; + +static int modparam_gpiobase = -1 /* dynamic */; +module_param_named(gpiobase, modparam_gpiobase, int, 0444); +MODULE_PARM_DESC(gpiobase, "The GPIO number base. -1 means dynamic, " + "which is the default."); + +static int ichx_write_bit(int reg, unsigned nr, int val, int verify) +{ + unsigned long flags; + u32 data; + int reg_nr = nr / 32; + int bit = nr & 0x1f; + int ret = 0; + + spin_lock_irqsave(&ichx_priv.lock, flags); + + data = ICHX_GPIO_READ(ichx_regs[reg][reg_nr]); + data = (data & ~(1 << bit)) | (val << bit); + ICHX_GPIO_WRITE(data, ichx_regs[reg][reg_nr]); + if (verify && (data != ICHX_GPIO_READ(ichx_regs[reg][reg_nr]))) + ret = -EPERM; + + spin_unlock_irqrestore(&ichx_priv.lock, flags); + + return ret; +} + +static int ichx_read_bit(int reg, unsigned nr) +{ + unsigned long flags; + u32 data; + int reg_nr = nr / 32; + int bit = nr & 0x1f; + + spin_lock_irqsave(&ichx_priv.lock, flags); + + data = ICHX_GPIO_READ(ichx_regs[reg][reg_nr]); + + spin_unlock_irqrestore(&ichx_priv.lock, flags); + + return data & (1 << bit) ? 1 : 0; +} + +static int ichx_gpio_direction_input(struct gpio_chip *gpio, unsigned nr) +{ + /* + * Try setting pin as an input and verify it worked since many pins + * are output-only. + */ + if (ichx_write_bit(GPIO_IO_SEL, nr, 1, 1)) + return -EINVAL; + + return 0; +} + +static int ichx_gpio_direction_output(struct gpio_chip *gpio, unsigned nr, + int val) +{ + /* Set GPIO output value. */ + ichx_write_bit(GPIO_LVL, nr, val, 0); + + /* + * Try setting pin as an output and verify it worked since many pins + * are input-only. + */ + if (ichx_write_bit(GPIO_IO_SEL, nr, 0, 1)) + return -EINVAL; + + return 0; +} + +static int ichx_gpio_get_direction(struct gpio_chip *chip, unsigned nr) +{ + /* Return 0 if IO pin is input, 1 if its an output */ + return !ichx_read_bit(GPIO_IO_SEL, nr); +} + +static int ichx_gpio_get(struct gpio_chip *chip, unsigned nr) +{ + return ichx_read_bit(GPIO_LVL, nr); +} + +static int ich6_gpio_get(struct gpio_chip *chip, unsigned nr) +{ + unsigned long flags; + u32 data; + + /* + * GPI 0 - 15 need to be read from the power management registers on + * a ICH6/3100 bridge. + */ + if (nr < 16) { + spin_lock_irqsave(&ichx_priv.lock, flags); + + /* GPI 0 - 15 are latched, write 1 to clear*/ + ICHX_PM_WRITE(1 << (16 + nr), ichx_priv.desc->gpe0_sts_ofs); + + data = ICHX_PM_READ(ichx_priv.desc->gpe0_sts_ofs); + + spin_unlock_irqrestore(&ichx_priv.lock, flags); + + return (data >> 16) & (1 << nr) ? 1 : 0; + } else { + return ichx_gpio_get(chip, nr); + } +} + +static int ichx_gpio_request(struct gpio_chip *chip, unsigned nr) +{ + /* + * Note we assume the BIOS properly set a bridge's USE value. Some + * chips (eg Intel 3100) have bogus USE values though, so first see if + * the chipset's USE value can be trusted for this specific bit. + * If it can't be trusted, assume that the pin can be used as a GPIO. + */ + if (ichx_priv.desc->use_sel_ignore[nr / 32] & (1 << (nr & 0x1f))) + return 1; + + return ichx_read_bit(GPIO_USE_SEL, nr) ? 0 : -ENODEV; +} + +static int ich6_gpio_request(struct gpio_chip *chip, unsigned nr) +{ + /* + * Fixups for bits 16 and 17 are necessary on the Intel ICH6/3100 + * brdige as they are controlled by USE register bits 0 and 1. See + * "Table 704 GPIO_USE_SEL1 register" in the i3100 datasheet for + * additional info. + */ + if ((nr == 16) || (nr == 17)) + nr -= 16; + + return ichx_gpio_request(chip, nr); +} + +static void ichx_gpio_set(struct gpio_chip *chip, unsigned nr, int val) +{ + ichx_write_bit(GPIO_LVL, nr, val, 0); +} + +static void __devinit ichx_gpiolib_setup(struct gpio_chip *chip) +{ + chip->owner = THIS_MODULE; + chip->label = DRV_NAME; + + /* Allow chip-specific overrides of request()/get() */ + chip->request = ichx_priv.desc->request ? + ichx_priv.desc->request : ichx_gpio_request; + chip->get = ichx_priv.desc->get ? + ichx_priv.desc->get : ichx_gpio_get; + + chip->set = ichx_gpio_set; + chip->get_direction = ichx_gpio_get_direction; + chip->direction_input = ichx_gpio_direction_input; + chip->direction_output = ichx_gpio_direction_output; + chip->base = modparam_gpiobase; + chip->ngpio = ichx_priv.desc->ngpio; + chip->can_sleep = 0; + chip->dbg_show = NULL; +} + +static int __devinit ichx_gpio_init(struct pci_dev *pdev, + const struct pci_device_id *ent, + struct platform_device *dev) +{ + int err; + + ichx_priv.pdev = pdev; + ichx_priv.dev = dev; + ichx_priv.desc = (struct ichx_desc *)ent->driver_data; + + /* Determine I/O address of GPIO registers */ + pci_read_config_dword(pdev, PCI_ICHX_GPIO_BAR, + (u32 *)&ichx_priv.gpio_base); + ichx_priv.gpio_base &= PCI_BASE_ADDRESS_IO_MASK; + if (!ichx_priv.gpio_base) { + printk(KERN_ERR "%s: GPIO BAR not enumerated\n", DRV_NAME); + return -ENODEV; + } + + /* + * If necessary, determine the I/O address of ACPI/power management + * registers which are needed to read the the GPE0 register for GPI pins + * 0 - 15 on some chipsets. + */ + if (ichx_priv.desc->gpe0_sts_ofs) { + pci_read_config_dword(pdev, PCI_ICHX_ACPI_BAR, + (u32 *)&ichx_priv.pm_base); + ichx_priv.pm_base &= PCI_BASE_ADDRESS_IO_MASK; + if (!ichx_priv.pm_base) + printk(KERN_WARNING "%s: ACPI BAR not enumerated, " + "GPI 0 - 15 unusable\n", DRV_NAME); + } + + /* Enable GPIO */ + pci_read_config_dword(pdev, PCI_ICHX_GPIO_CTRL, + &ichx_priv.orig_gpio_ctrl); + pci_write_config_dword(pdev, PCI_ICHX_GPIO_CTRL, + ichx_priv.orig_gpio_ctrl | 0x10); + + /* + * Reserve GPIO I/O region. The power management region is used by other + * drivers thus shouldn't be reserved. The GPIO I/O region is 64 + * bytes for older chipsets with <= 64 GPIO, 128 bytes for newer + * chipsets with > 64 GPIO. + */ + if (!devm_request_region(&dev->dev, ichx_priv.gpio_base, + ichx_priv.desc->ngpio > 64 ? 128 : 64, + "ichxgpio")) { + printk(KERN_ERR "%s: Can't request iomem (0x%lx)\n", + DRV_NAME, ichx_priv.gpio_base); + return -EBUSY; + } + + ichx_gpiolib_setup(&ichx_priv.chip); + + err = gpiochip_add(&ichx_priv.chip); + if (err) { + printk(KERN_ERR "%s: Failed to register GPIOs\n", DRV_NAME); + return err; + } + + printk(KERN_INFO "%s: GPIO from %d to %d on %s\n", DRV_NAME, + ichx_priv.chip.base, + ichx_priv.chip.base + ichx_priv.chip.ngpio - 1, + dev_name(&pdev->dev)); + + return 0; +} + +/* ICH6-based, 631xesb-based */ +static struct ichx_desc ich6_desc = { + /* Bridges using the ICH6 controller need fixups for GPIO 0 - 17 */ + .request = ich6_gpio_request, + .get = ich6_gpio_get, + + /* GPIO 0-15 are read in the GPE0_STS PM register */ + .gpe0_sts_ofs = 0x28, + + .ngpio = 50, +}; + +/* Intel 3100 */ +static struct ichx_desc i3100_desc = { + /* + * Bits 16,17, 20 of USE_SEL and bit 16 of USE_SEL2 always read 0 on + * the Intel 3100. See "Table 712. GPIO Summary Table" of 3100 + * Datasheet for more info. + */ + .use_sel_ignore = {0x00130000, 0x00010000, 0x0}, + + /* The 3100 needs fixups for GPIO 0 - 17 */ + .request = ich6_gpio_request, + .get = ich6_gpio_get, + + /* GPIO 0-15 are read in the GPE0_STS PM register */ + .gpe0_sts_ofs = 0x28, + + .ngpio = 50, +}; + +/* ICH7 and ICH8-based */ +static struct ichx_desc ich7_desc = { + .ngpio = 50, +}; + +/* ICH9-based */ +static struct ichx_desc ich9_desc = { + .ngpio = 61, +}; + +/* ICH10-based - Consumer/corporate versions have different amount of GPIO */ +static struct ichx_desc ich10_cons_desc = { + .ngpio = 51, +}; +static struct ichx_desc ich10_corp_desc = { + .ngpio = 72, +}; + +/* Intel 5 series, 6 series, 3400 series, and C200 series */ +static struct ichx_desc intel5_desc = { + .ngpio = 76, +}; + +/* + * Note that we don't register a PCI driver since the PCI device has additional + * functionality that is used by other drivers, eg iTCO_wdt. We use the table + * to probe for matching devices, then use a platform driver. + * + * Also note that some additional, old chipsets should in theory be supported + * by this driver (eg 82801XX chips), but they are left out due to the fact + * that they complicate the driver and there likely isn't much of a demand + * since a driver doesn't already exist for the 10+ years the chipsets have + * existed for. + */ +static DEFINE_PCI_DEVICE_TABLE(ichx_pci_tbl) = { + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_0, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_1, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_2, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_0, &ich7_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_1, &ich7_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_30, &ich7_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_31, &ich7_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_0, &ich7_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_1, &ich7_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_2, &ich7_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_3, &ich7_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_4, &ich7_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_1, &ich9_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_2, &ich9_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_4, &ich9_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_5, &ich9_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_7, &ich9_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_8, &ich9_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH10_0, &ich10_corp_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH10_3, &ich10_corp_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH10_1, &ich10_cons_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH10_2, &ich10_cons_desc) }, + { ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ESB2_0, &i3100_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x2671, &ich6_desc) }, /* 631Xesb series */ + { ICHX_GPIO_PCI_DEVICE(0x2672, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x2673, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x2674, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x2675, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x2676, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x2677, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x2678, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x2679, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x267a, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x267b, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x267c, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x267d, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x267e, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x267f, &ich6_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b00, &intel5_desc) }, /* 5 series */ + { ICHX_GPIO_PCI_DEVICE(0x3b01, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b02, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b03, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b04, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b05, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b06, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b07, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b08, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b09, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b0a, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b0b, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b0c, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b0d, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b0e, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b0f, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c41, &intel5_desc) }, /* 6 Series */ + { ICHX_GPIO_PCI_DEVICE(0x1c42, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c43, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c44, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c45, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c46, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c47, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c48, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c49, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c4a, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c4b, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c4c, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c4d, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c4e, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c4f, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c50, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c51, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c52, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c53, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c54, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c55, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c56, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c57, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c58, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c59, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c5a, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c5b, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c5c, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c5d, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c5e, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x1c5f, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b12, &intel5_desc) }, /* 3400 series */ + { ICHX_GPIO_PCI_DEVICE(0x3b14, &intel5_desc) }, + { ICHX_GPIO_PCI_DEVICE(0x3b16, &intel5_desc) }, + { 0, }, +}; +MODULE_DEVICE_TABLE(pci, ichx_pci_tbl); + +static int __devinit ichx_gpio_probe(struct platform_device *dev) +{ + struct pci_dev *pdev = NULL; + const struct pci_device_id *ent; + + spin_lock_init(&ichx_priv.lock); + + for_each_pci_dev(pdev) { + ent = pci_match_id(ichx_pci_tbl, pdev); + if (ent) + return ichx_gpio_init(pdev, ent, dev); + } + + return -ENODEV; +} + +static int __devexit ichx_gpio_remove(struct platform_device *dev) +{ + int ret = gpiochip_remove(&ichx_priv.chip); + + /* Restore original GPIO control register value */ + pci_write_config_dword(ichx_priv.pdev, PCI_ICHX_GPIO_CTRL, + ichx_priv.orig_gpio_ctrl); + + return ret; +} + +static struct platform_driver ichx_gpio_driver = { + .driver = { + .owner = THIS_MODULE, + .name = DRV_NAME, + }, + .probe = ichx_gpio_probe, + .remove = __devexit_p(ichx_gpio_remove), +}; + +static int __devinit ichx_gpio_init_module(void) +{ + int err = platform_driver_register(&ichx_gpio_driver); + if (err) + return err; + + ichx_gpio_platform_device = + platform_device_register_simple(DRV_NAME, -1, NULL, 0); + + if (IS_ERR(ichx_gpio_platform_device)) { + err = PTR_ERR(ichx_gpio_platform_device); + goto unreg_platform_driver; + } + + return 0; + +unreg_platform_driver: + platform_driver_unregister(&ichx_gpio_driver); + return err; +} + +static void __devexit ichx_gpio_exit_module(void) +{ + platform_device_unregister(ichx_gpio_platform_device); + platform_driver_unregister(&ichx_gpio_driver); +} + +module_init(ichx_gpio_init_module); +module_exit(ichx_gpio_exit_module); + +MODULE_AUTHOR("Peter Tyser "); +MODULE_DESCRIPTION("Intel ICHx series bridge GPIO driver"); +MODULE_LICENSE("GPL"); -- 1.7.0.4 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/