Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1755330Ab1CGHk4 (ORCPT ); Mon, 7 Mar 2011 02:40:56 -0500 Received: from smtp-out-189.synserver.de ([212.40.185.189]:1132 "HELO smtp-out-189.synserver.de" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with SMTP id S1755191Ab1CGHks (ORCPT ); Mon, 7 Mar 2011 02:40:48 -0500 X-SynServer-TrustedSrc: 1 X-SynServer-AuthUser: lars@laprican.de X-SynServer-PPID: 20568 From: Lars-Peter Clausen To: Greg Kroah-Hartman Cc: Ben Dooks , Kukjin Kim , Vasily Khoruzhick , linux-arm-kernel@lists.infradead.org, linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org, Lars-Peter Clausen Subject: [PATCH 1/2] USB: s3c2410_udc: Add common implementation for GPIO controlled pullups Date: Mon, 7 Mar 2011 08:41:59 +0100 Message-Id: <1299483720-18175-1-git-send-email-lars@metafoo.de> X-Mailer: git-send-email 1.7.2.3 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 4959 Lines: 161 Currently all boards using the s3c2410_udc driver use a GPIO to control the state of the pullup, as a result the same code is reimplemented in each board file. This patch adds support for using a GPIO to control the pullup state to the udc driver, so the boards can use a common implementation. Signed-off-by: Lars-Peter Clausen --- arch/arm/plat-s3c24xx/include/plat/udc.h | 4 ++ drivers/usb/gadget/s3c2410_udc.c | 60 +++++++++++++++++++++++++---- 2 files changed, 55 insertions(+), 9 deletions(-) diff --git a/arch/arm/plat-s3c24xx/include/plat/udc.h b/arch/arm/plat-s3c24xx/include/plat/udc.h index 546bb40..80457c6 100644 --- a/arch/arm/plat-s3c24xx/include/plat/udc.h +++ b/arch/arm/plat-s3c24xx/include/plat/udc.h @@ -27,6 +27,10 @@ enum s3c2410_udc_cmd_e { struct s3c2410_udc_mach_info { void (*udc_command)(enum s3c2410_udc_cmd_e); void (*vbus_draw)(unsigned int ma); + + unsigned int pullup_pin; + unsigned int pullup_pin_inverted; + unsigned int vbus_pin; unsigned char vbus_pin_inverted; }; diff --git a/drivers/usb/gadget/s3c2410_udc.c b/drivers/usb/gadget/s3c2410_udc.c index 2b02520..6d8b040 100644 --- a/drivers/usb/gadget/s3c2410_udc.c +++ b/drivers/usb/gadget/s3c2410_udc.c @@ -1481,7 +1481,9 @@ static int s3c2410_udc_set_pullup(struct s3c2410_udc *udc, int is_on) { dprintk(DEBUG_NORMAL, "%s()\n", __func__); - if (udc_info && udc_info->udc_command) { + if (udc_info && (udc_info->udc_command || + gpio_is_valid(udc_info->pullup_pin))) { + if (is_on) s3c2410_udc_enable(udc); else { @@ -1558,6 +1560,32 @@ static const struct usb_gadget_ops s3c2410_ops = { .vbus_draw = s3c2410_vbus_draw, }; +static void s3c2410_udc_command(enum s3c2410_udc_cmd_e cmd) +{ + if (!udc_info) + return; + + if (udc_info->udc_command) { + udc_info->udc_command(S3C2410_UDC_P_DISABLE); + } else if (gpio_is_valid(udc_info->pullup_pin)) { + int value; + + switch (cmd) { + case S3C2410_UDC_P_ENABLE: + value = 1; + break; + case S3C2410_UDC_P_DISABLE: + value = 0; + break; + default: + return; + } + value ^= udc_info->pullup_pin_inverted; + + gpio_set_value(udc_info->pullup_pin, value); + } +} + /*------------------------- gadget driver handling---------------------------*/ /* * s3c2410_udc_disable @@ -1579,8 +1607,7 @@ static void s3c2410_udc_disable(struct s3c2410_udc *dev) udc_write(0x1F, S3C2410_UDC_EP_INT_REG); /* Good bye, cruel world */ - if (udc_info && udc_info->udc_command) - udc_info->udc_command(S3C2410_UDC_P_DISABLE); + s3c2410_udc_command(S3C2410_UDC_P_DISABLE); /* Set speed to unknown */ dev->gadget.speed = USB_SPEED_UNKNOWN; @@ -1641,8 +1668,7 @@ static void s3c2410_udc_enable(struct s3c2410_udc *dev) udc_write(S3C2410_UDC_INT_EP0, S3C2410_UDC_EP_INT_EN_REG); /* time to say "hello, world" */ - if (udc_info && udc_info->udc_command) - udc_info->udc_command(S3C2410_UDC_P_ENABLE); + s3c2410_udc_command(S3C2410_UDC_P_ENABLE); } /* @@ -1917,6 +1943,17 @@ static int s3c2410_udc_probe(struct platform_device *pdev) udc->vbus = 1; } + if (udc_info && !udc_info->udc_command && + gpio_is_valid(udc_info->pullup_pin)) { + + retval = gpio_request_one(udc_info->pullup_pin, + udc_info->vbus_pin_inverted ? + GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW, + "udc pullup"); + if (retval) + goto err_vbus_irq; + } + if (s3c2410_udc_debugfs_root) { udc->regs_info = debugfs_create_file("registers", S_IRUGO, s3c2410_udc_debugfs_root, @@ -1929,6 +1966,9 @@ static int s3c2410_udc_probe(struct platform_device *pdev) return 0; +err_vbus_irq: + if (udc_info && udc_info->vbus_pin > 0) + free_irq(gpio_to_irq(udc_info->vbus_pin), udc); err_gpio_claim: if (udc_info && udc_info->vbus_pin > 0) gpio_free(udc_info->vbus_pin); @@ -1956,6 +1996,10 @@ static int s3c2410_udc_remove(struct platform_device *pdev) debugfs_remove(udc->regs_info); + if (udc_info && !udc_info->udc_command && + gpio_is_valid(udc_info->pullup_pin)) + gpio_free(udc_info->pullup_pin); + if (udc_info && udc_info->vbus_pin > 0) { irq = gpio_to_irq(udc_info->vbus_pin); free_irq(irq, udc); @@ -1987,16 +2031,14 @@ static int s3c2410_udc_remove(struct platform_device *pdev) #ifdef CONFIG_PM static int s3c2410_udc_suspend(struct platform_device *pdev, pm_message_t message) { - if (udc_info && udc_info->udc_command) - udc_info->udc_command(S3C2410_UDC_P_DISABLE); + s3c2410_udc_command(S3C2410_UDC_P_DISABLE); return 0; } static int s3c2410_udc_resume(struct platform_device *pdev) { - if (udc_info && udc_info->udc_command) - udc_info->udc_command(S3C2410_UDC_P_ENABLE); + s3c2410_udc_command(S3C2410_UDC_P_ENABLE); return 0; } -- 1.7.2.3 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/