Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S933042Ab1C3WRY (ORCPT ); Wed, 30 Mar 2011 18:17:24 -0400 Received: from wolverine01.qualcomm.com ([199.106.114.254]:51743 "EHLO wolverine01.qualcomm.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932342Ab1C3WRV (ORCPT ); Wed, 30 Mar 2011 18:17:21 -0400 X-IronPort-AV: E=McAfee;i="5400,1158,6301"; a="83047244" From: David Collins To: Liam Girdwood , Mark Brown , Samuel Ortiz Cc: David Brown , Daniel Walker , Bryan Huntsman , linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-arm-msm-owner@vger.kernel.org, David Collins Subject: [PATCH 1/2] regulator: pm8921-regulator: Add regulator driver for PM8921 Date: Wed, 30 Mar 2011 15:17:12 -0700 Message-Id: <1301523432-6017-1-git-send-email-collinsd@codeaurora.org> X-Mailer: git-send-email 1.7.3.3 In-Reply-To: <1301523361-5982-1-git-send-email-collinsd@codeaurora.org> References: <1301523361-5982-1-git-send-email-collinsd@codeaurora.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 71803 Lines: 2492 Create a regulator driver to control all regulators on the Qualcomm PM8921 PMIC chip. This chip contains many different types of regulators with a wide range of abilities and voltage ranges. Eight different regulator types are available on the PM8921. These are managed via 7 different type values in the driver: LDO - low drop out regulator (supports both NMOS and PMOS LDOs) NLDO1200 - 1.2A NMOS LDO (different control structure than other LDOs) SMPS - switched-mode power supply FTSMPS - fast transient SMPS VS - voltage switch VS300 - 300mA voltage switch (different control structure than other switches) NCP - negative charge pump The driver interfaces with the PMIC using Qualcomm's SSBI bus. Calls to this bus are abtracted through the pm8xxx_readb/writeb API. Regulator framework operation callback functions work as expected with one exception: pm8921_vreg_get_mode and pm8921_vreg_set_mode. These callbacks are shared by all regulator types in the driver. The mode setting scheme was modified from the normal framework usage to accommodate pin control. Pin control allows a regulator that has been disabled by software writing to its control registers to become enabled by a hardware pin. Many of the PM8921 regulators support pin control (as do those on other Qualcomm PMIC chips). It is primarily used by peripheral devices that need to be able to actively manage power usage while the main processor which is connected to the PMIC SSBI bus is asleep. Pin control is handled in the PM8921 regulator driver via the set_mode callback function pm8921_vreg_set_mode. It treats mode values as follows: REGULATOR_MODE_FAST - set to high power mode (HPM) REGULATOR_MODE_NORMAL - remove a vote for pin control REGULATOR_MODE_IDLE - vote for pin control (ref-counted) REGULATOR_MODE_STANDBY - set to low power mode (LPM) There is an additional caveat that pin control mode will override LPM such that, a set mode call for LPM will be ignored if the pin control reference count is greater than 0. Similarly, HPM will override pin control mode. Transitivity is not maintained though, because the mode can be changed from HPM to LPM. This ensures that it is still possible to transition freely between LPM and HPM with calls to regulator_set_optimum_mode. Signed-off-by: David Collins --- drivers/mfd/pm8921-core.c | 32 +- drivers/regulator/Kconfig | 10 + drivers/regulator/Makefile | 1 + drivers/regulator/pm8921-regulator.c | 2211 ++++++++++++++++++++++++++++ include/linux/mfd/pm8xxx/pm8921.h | 3 + include/linux/regulator/pm8921-regulator.h | 97 ++ 6 files changed, 2353 insertions(+), 1 deletions(-) create mode 100644 drivers/regulator/pm8921-regulator.c create mode 100644 include/linux/regulator/pm8921-regulator.h diff --git a/drivers/mfd/pm8921-core.c b/drivers/mfd/pm8921-core.c index d0a991c..3b2ca69 100644 --- a/drivers/mfd/pm8921-core.c +++ b/drivers/mfd/pm8921-core.c @@ -119,8 +119,9 @@ static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data struct pm8921 *pmic, u32 rev) { - int ret = 0, irq_base = 0; + int ret = 0, irq_base = 0, i; struct pm_irq_chip *irq_chip; + static struct mfd_cell *mfd_regulators; if (pdata->irq_pdata) { pdata->irq_pdata->irq_cdata.nirqs = PM8921_NR_IRQS; @@ -162,6 +163,35 @@ static int __devinit pm8921_add_subdevices(const struct pm8921_platform_data } } + /* Add one device for each regulator used by the board. */ + if (pdata->num_regulators > 0 && pdata->regulator_pdatas) { + mfd_regulators = kzalloc(sizeof(struct mfd_cell) + * (pdata->num_regulators), GFP_KERNEL); + if (!mfd_regulators) { + pr_err("Cannot allocate %d bytes for pm8921 regulator " + "mfd cells\n", sizeof(struct mfd_cell) + * (pdata->num_regulators)); + ret = -ENOMEM; + goto bail; + } + for (i = 0; i < pdata->num_regulators; i++) { + mfd_regulators[i].name = PM8921_REGULATOR_DEV_NAME; + mfd_regulators[i].id = pdata->regulator_pdatas[i].id; + mfd_regulators[i].platform_data = + &(pdata->regulator_pdatas[i]); + mfd_regulators[i].data_size = + sizeof(struct pm8921_regulator_platform_data); + } + ret = mfd_add_devices(pmic->dev, 0, mfd_regulators, + pdata->num_regulators, NULL, irq_base); + kfree(mfd_regulators); + if (ret) { + pr_err("Failed to add regulator subdevices ret=%d\n", + ret); + goto bail; + } + } + return 0; bail: if (pmic->irq_chip) { diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index e1d9436..c212156 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -272,5 +272,15 @@ config REGULATOR_TPS6524X serial interface currently supported on the sequencer serial port controller. +config REGULATOR_PM8921 + tristate "Qualcomm PM8921 PMIC Power regulators" + depends on MFD_PM8921_CORE + default y if MFD_PM8921_CORE + help + This driver supports voltage regulators in the Qualcomm PM8921 PMIC + chip. The PM8921 provides several different varieties of LDO and + switching regulators. It also provides a negative charge pump and + voltage switches. + endif diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index 0b5e88c..bec35ac 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -40,5 +40,6 @@ obj-$(CONFIG_REGULATOR_TPS6524X) += tps6524x-regulator.o obj-$(CONFIG_REGULATOR_88PM8607) += 88pm8607.o obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o obj-$(CONFIG_REGULATOR_AB8500) += ab8500.o +obj-$(CONFIG_REGULATOR_PM8921) += pm8921-regulator.o ccflags-$(CONFIG_REGULATOR_DEBUG) += -DDEBUG diff --git a/drivers/regulator/pm8921-regulator.c b/drivers/regulator/pm8921-regulator.c new file mode 100644 index 0000000..f686757 --- /dev/null +++ b/drivers/regulator/pm8921-regulator.c @@ -0,0 +1,2211 @@ +/* + * Copyright (c) 2011, Code Aurora Forum. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#define pr_fmt(fmt) "%s: " fmt, __func__ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define REGULATOR_TYPE_LDO 0 +#define REGULATOR_TYPE_NLDO1200 1 +#define REGULATOR_TYPE_SMPS 2 +#define REGULATOR_TYPE_FTSMPS 3 +#define REGULATOR_TYPE_VS 4 +#define REGULATOR_TYPE_VS300 5 +#define REGULATOR_TYPE_NCP 6 + +/* Common Masks */ +#define REGULATOR_ENABLE_MASK 0x80 +#define REGULATOR_ENABLE 0x80 +#define REGULATOR_DISABLE 0x00 + +#define REGULATOR_BANK_MASK 0xF0 +#define REGULATOR_BANK_SEL(n) ((n) << 4) +#define REGULATOR_BANK_WRITE 0x80 + +#define LDO_TEST_BANKS 7 +#define NLDO1200_TEST_BANKS 5 +#define SMPS_TEST_BANKS 8 +#define REGULATOR_TEST_BANKS_MAX SMPS_TEST_BANKS + +/* LDO masks and values */ + +/* CTRL register */ +#define LDO_ENABLE_MASK 0x80 +#define LDO_ENABLE 0x80 +#define LDO_PULL_DOWN_ENABLE_MASK 0x40 +#define LDO_PULL_DOWN_ENABLE 0x40 + +#define LDO_CTRL_PM_MASK 0x20 +#define LDO_CTRL_PM_HPM 0x00 +#define LDO_CTRL_PM_LPM 0x20 + +#define LDO_CTRL_VPROG_MASK 0x1F + +/* TEST register bank 0 */ +#define LDO_TEST_LPM_MASK 0x40 +#define LDO_TEST_LPM_SEL_CTRL 0x00 +#define LDO_TEST_LPM_SEL_TCXO 0x40 + +/* TEST register bank 2 */ +#define LDO_TEST_VPROG_UPDATE_MASK 0x08 +#define LDO_TEST_RANGE_SEL_MASK 0x04 +#define LDO_TEST_FINE_STEP_MASK 0x02 +#define LDO_TEST_FINE_STEP_SHIFT 1 + +/* TEST register bank 4 */ +#define LDO_TEST_RANGE_EXT_MASK 0x01 + +/* TEST register bank 5 */ +#define LDO_TEST_PIN_CTRL_MASK 0x0F +#define LDO_TEST_PIN_CTRL_EN3 0x08 +#define LDO_TEST_PIN_CTRL_EN2 0x04 +#define LDO_TEST_PIN_CTRL_EN1 0x02 +#define LDO_TEST_PIN_CTRL_EN0 0x01 + +/* TEST register bank 6 */ +#define LDO_TEST_PIN_CTRL_LPM_MASK 0x0F + +/* Allowable voltage ranges */ +#define PLDO_LOW_UV_MIN 750000 +#define PLDO_LOW_UV_MAX 1537500 +#define PLDO_LOW_FINE_STEP_UV 12500 + +#define PLDO_NORM_UV_MIN 1500000 +#define PLDO_NORM_UV_MAX 3075000 +#define PLDO_NORM_FINE_STEP_UV 25000 + +#define PLDO_HIGH_UV_MIN 1750000 +#define PLDO_HIGH_UV_MAX 4900000 +#define PLDO_HIGH_FINE_STEP_UV 50000 + +#define NLDO_UV_MIN 750000 +#define NLDO_UV_MAX 1537500 +#define NLDO_FINE_STEP_UV 12500 + +/* NLDO1200 masks and values */ + +/* CTRL register */ +#define NLDO1200_ENABLE_MASK 0x80 +#define NLDO1200_LDO_ENABLE 0x80 + +/* Legacy mode */ +#define NLDO1200_LEGACY_PM_MASK 0x20 +#define NLDO1200_LEGACY_PM_HPM 0x00 +#define NLDO1200_LEGACY_PM_LPM 0x20 + +/* Advanced mode */ +#define NLDO1200_CTRL_RANGE_MASK 0x40 +#define NLDO1200_CTRL_RANGE_HIGH 0x00 +#define NLDO1200_CTRL_RANGE_LOW 0x40 +#define NLDO1200_CTRL_VPROG_MASK 0x3F + +#define NLDO1200_LOW_UV_MIN 375000 +#define NLDO1200_LOW_UV_MAX 768750 +#define NLDO1200_LOW_UV_STEP 6250 + +#define NLDO1200_HIGH_UV_MIN 750000 +#define NLDO1200_HIGH_UV_MAX 1537500 +#define NLDO1200_HIGH_UV_STEP 12500 + +/* TEST register bank 0 */ +#define NLDO1200_TEST_LPM_MASK 0x04 +#define NLDO1200_TEST_LPM_SEL_CTRL 0x00 +#define NLDO1200_TEST_LPM_SEL_TCXO 0x04 + +/* TEST register bank 1 */ +#define NLDO1200_PULL_DOWN_ENABLE_MASK 0x02 +#define NLDO1200_PULL_DOWN_ENABLE 0x02 + +/* TEST register bank 2 */ +#define NLDO1200_ADVANCED_MODE_MASK 0x08 +#define NLDO1200_ADVANCED_MODE 0x00 +#define NLDO1200_LEGACY_MODE 0x08 + +/* Advanced mode power mode control */ +#define NLDO1200_ADVANCED_PM_MASK 0x02 +#define NLDO1200_ADVANCED_PM_HPM 0x00 +#define NLDO1200_ADVANCED_PM_LPM 0x02 + +#define NLDO1200_IN_ADVANCED_MODE(vreg) \ + ((vreg->test_reg[2] & NLDO1200_ADVANCED_MODE_MASK) \ + == NLDO1200_ADVANCED_MODE) + +/* SMPS masks and values */ + +/* CTRL register */ + +/* Legacy mode */ +#define SMPS_LEGACY_ENABLE 0x80 +#define SMPS_LEGACY_PULL_DOWN_ENABLE 0x40 +#define SMPS_LEGACY_VREF_SEL_MASK 0x20 +#define SMPS_LEGACY_VPROG_MASK 0x1F + +/* Advanced mode */ +#define SMPS_ADVANCED_BAND_MASK 0xC0 +#define SMPS_ADVANCED_BAND_OFF 0x00 +#define SMPS_ADVANCED_BAND_1 0x40 +#define SMPS_ADVANCED_BAND_2 0x80 +#define SMPS_ADVANCED_BAND_3 0xC0 +#define SMPS_ADVANCED_VPROG_MASK 0x3F + +/* Legacy mode voltage ranges */ +#define SMPS_MODE1_UV_MIN 1500000 +#define SMPS_MODE1_UV_MAX 3050000 +#define SMPS_MODE1_UV_STEP 50000 + +#define SMPS_MODE2_UV_MIN 750000 +#define SMPS_MODE2_UV_MAX 1525000 +#define SMPS_MODE2_UV_STEP 25000 + +#define SMPS_MODE3_UV_MIN 375000 +#define SMPS_MODE3_UV_MAX 1150000 +#define SMPS_MODE3_UV_STEP 25000 + +/* Advanced mode voltage ranges */ +#define SMPS_BAND3_UV_MIN 1500000 +#define SMPS_BAND3_UV_MAX 3075000 +#define SMPS_BAND3_UV_STEP 25000 + +#define SMPS_BAND2_UV_MIN 750000 +#define SMPS_BAND2_UV_MAX 1537500 +#define SMPS_BAND2_UV_STEP 12500 + +#define SMPS_BAND1_UV_MIN 375000 +#define SMPS_BAND1_UV_MAX 1162500 +#define SMPS_BAND1_UV_STEP 12500 + +#define SMPS_UV_MIN SMPS_MODE3_UV_MIN +#define SMPS_UV_MAX SMPS_MODE1_UV_MAX + +/* Test2 register bank 1 */ +#define SMPS_LEGACY_VLOW_SEL_MASK 0x01 + +/* Test2 register bank 6 */ +#define SMPS_ADVANCED_PULL_DOWN_ENABLE 0x08 + +/* Test2 register bank 7 */ +#define SMPS_ADVANCED_MODE_MASK 0x02 +#define SMPS_ADVANCED_MODE 0x02 +#define SMPS_LEGACY_MODE 0x00 + +#define SMPS_IN_ADVANCED_MODE(vreg) \ + ((vreg->test_reg[7] & SMPS_ADVANCED_MODE_MASK) == SMPS_ADVANCED_MODE) + +/* BUCK_SLEEP_CNTRL register */ +#define SMPS_PIN_CTRL_MASK 0xF0 +#define SMPS_PIN_CTRL_A1 0x80 +#define SMPS_PIN_CTRL_A0 0x40 +#define SMPS_PIN_CTRL_D1 0x20 +#define SMPS_PIN_CTRL_D0 0x10 + +#define SMPS_PIN_CTRL_LPM_MASK 0x0F +#define SMPS_PIN_CTRL_LPM_A1 0x08 +#define SMPS_PIN_CTRL_LPM_A0 0x04 +#define SMPS_PIN_CTRL_LPM_D1 0x02 +#define SMPS_PIN_CTRL_LPM_D0 0x01 + +/* BUCK_CLOCK_CNTRL register */ +#define SMPS_CLK_DIVIDE2 0x40 + +#define SMPS_CLK_CTRL_MASK 0x30 +#define SMPS_CLK_CTRL_FOLLOW_TCXO 0x00 +#define SMPS_CLK_CTRL_PWM 0x10 +#define SMPS_CLK_CTRL_PFM 0x20 + +/* FTSMPS masks and values */ + +/* CTRL register */ +#define FTSMPS_VCTRL_BAND_MASK 0xC0 +#define FTSMPS_VCTRL_BAND_OFF 0x00 +#define FTSMPS_VCTRL_BAND_1 0x40 +#define FTSMPS_VCTRL_BAND_2 0x80 +#define FTSMPS_VCTRL_BAND_3 0xC0 +#define FTSMPS_VCTRL_VPROG_MASK 0x3F + +#define FTSMPS_BAND1_UV_MIN 350000 +#define FTSMPS_BAND1_UV_MAX 650000 +#define FTSMPS_BAND1_UV_STEP 6250 + +#define FTSMPS_BAND2_UV_MIN 700000 +#define FTSMPS_BAND2_UV_MAX 1400000 +#define FTSMPS_BAND2_UV_STEP 12500 + +#define FTSMPS_BAND3_UV_SETPOINT_MIN 1500000 +#define FTSMPS_BAND3_UV_MIN 1400000 +#define FTSMPS_BAND3_UV_MAX 3300000 +#define FTSMPS_BAND3_UV_STEP 50000 + +#define FTSMPS_UV_MIN FTSMPS_BAND_1_UV_MIN +#define FTSMPS_UV_MAX FTSMPS_BAND_3_UV_MAX + +/* FTS_CNFG1 register bank 0 */ +#define FTSMPS_CNFG1_PM_MASK 0x0C +#define FTSMPS_CNFG1_PM_PWM 0x00 +#define FTSMPS_CNFG1_PM_PFM 0x08 + +/* PWR_CNFG register */ +#define FTSMPS_PULL_DOWN_ENABLE_MASK 0x40 +#define FTSMPS_PULL_DOWN_ENABLE 0x40 + +/* + * Band 1 of PMIC 8921 FTSMPS regulators only supports set points with the 3 + * LSB's equal to 0. This is accomplished in the macro by truncating the bits. + */ +#define PM8921_FTSMPS_BAND_1_COMPENSATE(vprog) ((vprog) & ~0x7) + +/* VS masks and values */ + +/* CTRL register */ +#define VS_ENABLE_MASK 0x80 +#define VS_ENABLE 0x80 +#define VS_PULL_DOWN_ENABLE_MASK 0x40 +#define VS_PULL_DOWN_ENABLE 0x40 + +#define VS_PIN_CTRL_MASK 0x0F +#define VS_PIN_CTRL_EN0 0x08 +#define VS_PIN_CTRL_EN1 0x04 +#define VS_PIN_CTRL_EN2 0x02 +#define VS_PIN_CTRL_EN3 0x01 + +/* VS300 masks and values */ + +/* CTRL register */ +#define VS300_CTRL_ENABLE_MASK 0xC0 +#define VS300_CTRL_DISABLE 0x00 +#define VS300_CTRL_ENABLE 0x40 + +#define VS300_PULL_DOWN_ENABLE_MASK 0x20 +#define VS300_PULL_DOWN_ENABLE 0x20 + +/* NCP masks and values */ + +/* CTRL register */ +#define NCP_ENABLE_MASK 0x80 +#define NCP_ENABLE 0x80 +#define NCP_VPROG_MASK 0x1F + +#define NCP_UV_MIN 1500000 +#define NCP_UV_MAX 3050000 +#define NCP_UV_STEP 50000 + +struct pm8921_vreg { + /* Configuration data */ + struct regulator_dev *rdev; + struct device *dev; + const char *name; + struct pm8921_regulator_platform_data pdata; + const int hpm_min_load; + const u16 ctrl_addr; + const u16 test_addr; + const u16 clk_ctrl_addr; + const u16 sleep_ctrl_addr; + const u16 pfm_ctrl_addr; + const u16 pwr_cnfg_addr; + const u8 type; + /* State data */ + int save_uV; + int save_uA; + unsigned pc_vote; + unsigned optimum; + u8 test_reg[REGULATOR_TEST_BANKS_MAX]; + u8 ctrl_reg; + u8 clk_ctrl_reg; + u8 sleep_ctrl_reg; + u8 pfm_ctrl_reg; + u8 pwr_cnfg_reg; + u8 state; +}; + +#define vreg_err(vreg, fmt, ...) \ + pr_err("%s: " fmt, vreg->name, ##__VA_ARGS__) + +#define LDO(_id, _ctrl_addr, _test_addr, _hpm_min_load) \ + [PM8921_VREG_ID_##_id] = { \ + .type = REGULATOR_TYPE_LDO, \ + .ctrl_addr = _ctrl_addr, \ + .test_addr = _test_addr, \ + .hpm_min_load = PM8921_VREG_##_hpm_min_load##_HPM_MIN_LOAD, \ + } + +#define NLDO1200(_id, _ctrl_addr, _test_addr, _hpm_min_load) \ + [PM8921_VREG_ID_##_id] = { \ + .type = REGULATOR_TYPE_NLDO1200, \ + .ctrl_addr = _ctrl_addr, \ + .test_addr = _test_addr, \ + .hpm_min_load = PM8921_VREG_##_hpm_min_load##_HPM_MIN_LOAD, \ + } + +#define SMPS(_id, _ctrl_addr, _test_addr, _clk_ctrl_addr, _sleep_ctrl_addr, \ + _hpm_min_load) \ + [PM8921_VREG_ID_##_id] = { \ + .type = REGULATOR_TYPE_SMPS, \ + .ctrl_addr = _ctrl_addr, \ + .test_addr = _test_addr, \ + .clk_ctrl_addr = _clk_ctrl_addr, \ + .sleep_ctrl_addr = _sleep_ctrl_addr, \ + .hpm_min_load = PM8921_VREG_##_hpm_min_load##_HPM_MIN_LOAD, \ + } + +#define FTSMPS(_id, _pwm_ctrl_addr, _fts_cnfg1_addr, _pfm_ctrl_addr, \ + _pwr_cnfg_addr, _hpm_min_load) \ + [PM8921_VREG_ID_##_id] = { \ + .type = REGULATOR_TYPE_FTSMPS, \ + .ctrl_addr = _pwm_ctrl_addr, \ + .test_addr = _fts_cnfg1_addr, \ + .pfm_ctrl_addr = _pfm_ctrl_addr, \ + .pwr_cnfg_addr = _pwr_cnfg_addr, \ + .hpm_min_load = PM8921_VREG_##_hpm_min_load##_HPM_MIN_LOAD, \ + } + +#define VS(_id, _ctrl_addr) \ + [PM8921_VREG_ID_##_id] = { \ + .type = REGULATOR_TYPE_VS, \ + .ctrl_addr = _ctrl_addr, \ + } + +#define VS300(_id, _ctrl_addr) \ + [PM8921_VREG_ID_##_id] = { \ + .type = REGULATOR_TYPE_VS300, \ + .ctrl_addr = _ctrl_addr, \ + } + +#define NCP(_id, _ctrl_addr) \ + [PM8921_VREG_ID_##_id] = { \ + .type = REGULATOR_TYPE_NCP, \ + .ctrl_addr = _ctrl_addr, \ + } + +static struct pm8921_vreg pm8921_vreg[] = { + /* id ctrl test hpm_min */ + LDO(L1, 0x0AE, 0x0AF, LDO_150), + LDO(L2, 0x0B0, 0x0B1, LDO_150), + LDO(L3, 0x0B2, 0x0B3, LDO_150), + LDO(L4, 0x0B4, 0x0B5, LDO_50), + LDO(L5, 0x0B6, 0x0B7, LDO_300), + LDO(L6, 0x0B8, 0x0B9, LDO_600), + LDO(L7, 0x0BA, 0x0BB, LDO_150), + LDO(L8, 0x0BC, 0x0BD, LDO_300), + LDO(L9, 0x0BE, 0x0BF, LDO_300), + LDO(L10, 0x0C0, 0x0C1, LDO_600), + LDO(L11, 0x0C2, 0x0C3, LDO_150), + LDO(L12, 0x0C4, 0x0C5, LDO_150), + LDO(L14, 0x0C8, 0x0C9, LDO_50), + LDO(L15, 0x0CA, 0x0CB, LDO_150), + LDO(L16, 0x0CC, 0x0CD, LDO_300), + LDO(L17, 0x0CE, 0x0CF, LDO_150), + LDO(L18, 0x0D0, 0x0D1, LDO_150), + LDO(L21, 0x0D6, 0x0D7, LDO_150), + LDO(L22, 0x0D8, 0x0D9, LDO_150), + LDO(L23, 0x0DA, 0x0DB, LDO_150), + + /* id ctrl test hpm_min */ + NLDO1200(L24, 0x0DC, 0x0DD, LDO_1200), + NLDO1200(L25, 0x0DE, 0x0DF, LDO_1200), + NLDO1200(L26, 0x0E0, 0x0E1, LDO_1200), + NLDO1200(L27, 0x0E2, 0x0E3, LDO_1200), + NLDO1200(L28, 0x0E4, 0x0E5, LDO_1200), + + /* id ctrl test hpm_min */ + LDO(L29, 0x0E6, 0x0E7, LDO_150), + + /* id ctrl test2 clk sleep hpm_min */ + SMPS(S1, 0x1D0, 0x1D5, 0x009, 0x1D2, SMPS_1500), + SMPS(S2, 0x1D8, 0x1DD, 0x00A, 0x1DA, SMPS_1500), + SMPS(S3, 0x1E0, 0x1E5, 0x00B, 0x1E2, SMPS_1500), + SMPS(S4, 0x1E8, 0x1ED, 0x011, 0x1EA, SMPS_1500), + + /* id ctrl fts_cnfg1 pfm pwr_cnfg hpm_min */ + FTSMPS(S5, 0x025, 0x02E, 0x026, 0x032, SMPS_2000), + FTSMPS(S6, 0x036, 0x03F, 0x037, 0x043, SMPS_2000), + + /* id ctrl test2 clk sleep hpm_min */ + SMPS(S7, 0x1F0, 0x1F5, 0x012, 0x1F2, SMPS_1500), + SMPS(S8, 0x1F8, 0x1FD, 0x013, 0x1FA, SMPS_1500), + + /* id ctrl */ + VS(LVS1, 0x060), + VS300(LVS2, 0x062), + VS(LVS3, 0x064), + VS(LVS4, 0x066), + VS(LVS5, 0x068), + VS(LVS6, 0x06A), + VS(LVS7, 0x06C), + VS300(USB_OTG, 0x06E), + VS300(HDMI_MVS, 0x070), + + /* id ctrl */ + NCP(NCP, 0x090), +}; + +static int pm8921_vreg_write(struct pm8921_vreg *vreg, u16 addr, u8 val, + u8 mask, u8 *reg_save) +{ + int rc = 0; + u8 reg; + + reg = (*reg_save & ~mask) | (val & mask); + if (reg != *reg_save) + rc = pm8xxx_writeb(vreg->dev->parent, addr, reg); + + if (rc) + pr_err("pm8xxx_writeb failed; addr=0x%03X, rc=%d\n", addr, rc); + else + *reg_save = reg; + + return rc; +} + +static int pm8921_vreg_is_pin_controlled(struct pm8921_vreg *vreg) +{ + int ret = 0; + + switch (vreg->type) { + case REGULATOR_TYPE_LDO: + ret = ((vreg->test_reg[5] & LDO_TEST_PIN_CTRL_MASK) << 4) + | (vreg->test_reg[6] & LDO_TEST_PIN_CTRL_LPM_MASK); + break; + case REGULATOR_TYPE_SMPS: + ret = vreg->sleep_ctrl_reg + & (SMPS_PIN_CTRL_MASK | SMPS_PIN_CTRL_LPM_MASK); + break; + case REGULATOR_TYPE_VS: + ret = vreg->ctrl_reg & VS_PIN_CTRL_MASK; + break; + } + + return ret; +} + +static int _pm8921_vreg_is_enabled(struct pm8921_vreg *vreg) +{ + int rc = 0; + + /* + * All regulator types except advanced mode SMPS, FTSMPS, and VS300 have + * enable bit in bit 7 of the control register. Pin control also does + * not work for advanced mode SMPS. + */ + switch (vreg->type) { + case REGULATOR_TYPE_FTSMPS: + if ((vreg->ctrl_reg & FTSMPS_VCTRL_BAND_MASK) + != FTSMPS_VCTRL_BAND_OFF) + rc = 1; + break; + case REGULATOR_TYPE_VS300: + if ((vreg->ctrl_reg & VS300_CTRL_ENABLE_MASK) + != VS300_CTRL_DISABLE) + rc = 1; + break; + case REGULATOR_TYPE_SMPS: + if (SMPS_IN_ADVANCED_MODE(vreg)) { + if ((vreg->ctrl_reg & SMPS_ADVANCED_BAND_MASK) + != SMPS_ADVANCED_BAND_OFF) + rc = 1; + } else if ((vreg->ctrl_reg & SMPS_LEGACY_ENABLE) + || pm8921_vreg_is_pin_controlled(vreg)) { + rc = 1; + } + break; + default: + if (((vreg->ctrl_reg & REGULATOR_ENABLE_MASK) + == REGULATOR_ENABLE) + || pm8921_vreg_is_pin_controlled(vreg)) + rc = 1; + } + + return rc; +} + +static int pm8921_vreg_is_enabled(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + + return _pm8921_vreg_is_enabled(vreg); +} + +static int pm8921_pldo_get_voltage(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + int vmin, fine_step; + u8 range_ext, range_sel, vprog, fine_step_reg; + + fine_step_reg = vreg->test_reg[2] & LDO_TEST_FINE_STEP_MASK; + range_sel = vreg->test_reg[2] & LDO_TEST_RANGE_SEL_MASK; + range_ext = vreg->test_reg[4] & LDO_TEST_RANGE_EXT_MASK; + vprog = vreg->ctrl_reg & LDO_CTRL_VPROG_MASK; + + vprog = (vprog << 1) | (fine_step_reg >> LDO_TEST_FINE_STEP_SHIFT); + + if (range_sel) { + /* low range mode */ + fine_step = PLDO_LOW_FINE_STEP_UV; + vmin = PLDO_LOW_UV_MIN; + } else if (!range_ext) { + /* normal mode */ + fine_step = PLDO_NORM_FINE_STEP_UV; + vmin = PLDO_NORM_UV_MIN; + } else { + /* high range mode */ + fine_step = PLDO_HIGH_FINE_STEP_UV; + vmin = PLDO_HIGH_UV_MIN; + } + + return fine_step * vprog + vmin; +} + +static int pm8921_pldo_set_voltage(struct regulator_dev *rdev, int min_uV, + int max_uV, unsigned *selector) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + int vmin, rc = 0; + unsigned vprog, fine_step; + u8 range_ext, range_sel, fine_step_reg; + + if (min_uV < PLDO_LOW_UV_MIN || min_uV > PLDO_HIGH_UV_MAX) { + vreg_err(vreg, "requested voltage %d is outside of allowed " + "range.\n", min_uV); + return -EINVAL; + } + + if (min_uV < PLDO_NORM_UV_MIN) { + vmin = PLDO_LOW_UV_MIN; + fine_step = PLDO_LOW_FINE_STEP_UV; + range_ext = 0; + range_sel = LDO_TEST_RANGE_SEL_MASK; + } else if (min_uV < PLDO_NORM_UV_MAX + PLDO_NORM_FINE_STEP_UV) { + vmin = PLDO_NORM_UV_MIN; + fine_step = PLDO_NORM_FINE_STEP_UV; + range_ext = 0; + range_sel = 0; + } else { + vmin = PLDO_HIGH_UV_MIN; + fine_step = PLDO_HIGH_FINE_STEP_UV; + range_ext = LDO_TEST_RANGE_EXT_MASK; + range_sel = 0; + } + + vprog = (min_uV - vmin) / fine_step; + fine_step_reg = (vprog & 1) << LDO_TEST_FINE_STEP_SHIFT; + vprog >>= 1; + + /* + * Disable program voltage update if range extension, range select, + * or fine step have changed and the regulator is enabled. + */ + if (_pm8921_vreg_is_enabled(vreg) && + (((range_ext ^ vreg->test_reg[4]) & LDO_TEST_RANGE_EXT_MASK) + || ((range_sel ^ vreg->test_reg[2]) & LDO_TEST_RANGE_SEL_MASK) + || ((fine_step_reg ^ vreg->test_reg[2]) + & LDO_TEST_FINE_STEP_MASK))) { + rc = pm8921_vreg_write(vreg, vreg->test_addr, + REGULATOR_BANK_SEL(2) | REGULATOR_BANK_WRITE, + REGULATOR_BANK_MASK | LDO_TEST_VPROG_UPDATE_MASK, + &vreg->test_reg[2]); + if (rc) + goto bail; + } + + /* Write new voltage. */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, vprog, + LDO_CTRL_VPROG_MASK, &vreg->ctrl_reg); + if (rc) + goto bail; + + /* Write range extension. */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + range_ext | REGULATOR_BANK_SEL(4) + | REGULATOR_BANK_WRITE, + LDO_TEST_RANGE_EXT_MASK | REGULATOR_BANK_MASK, + &vreg->test_reg[4]); + if (rc) + goto bail; + + /* Write fine step, range select and program voltage update. */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + fine_step_reg | range_sel | REGULATOR_BANK_SEL(2) + | REGULATOR_BANK_WRITE | LDO_TEST_VPROG_UPDATE_MASK, + LDO_TEST_FINE_STEP_MASK | LDO_TEST_RANGE_SEL_MASK + | REGULATOR_BANK_MASK | LDO_TEST_VPROG_UPDATE_MASK, + &vreg->test_reg[2]); +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_nldo_get_voltage(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + u8 vprog, fine_step_reg; + + fine_step_reg = vreg->test_reg[2] & LDO_TEST_FINE_STEP_MASK; + vprog = vreg->ctrl_reg & LDO_CTRL_VPROG_MASK; + + vprog = (vprog << 1) | (fine_step_reg >> LDO_TEST_FINE_STEP_SHIFT); + + return NLDO_FINE_STEP_UV * vprog + NLDO_UV_MIN; +} + +static int pm8921_nldo_set_voltage(struct regulator_dev *rdev, int min_uV, + int max_uV, unsigned *selector) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + unsigned vprog, fine_step_reg; + int rc; + + if (min_uV < NLDO_UV_MIN || min_uV > NLDO_UV_MAX) { + vreg_err(vreg, "requested voltage %d is outside of allowed " + "range.\n", min_uV); + return -EINVAL; + } + + vprog = (min_uV - NLDO_UV_MIN) / NLDO_FINE_STEP_UV; + fine_step_reg = (vprog & 1) << LDO_TEST_FINE_STEP_SHIFT; + vprog >>= 1; + + /* Write new voltage. */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, vprog, + LDO_CTRL_VPROG_MASK, &vreg->ctrl_reg); + if (rc) + goto bail; + + /* Write fine step. */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + fine_step_reg | REGULATOR_BANK_SEL(2) + | REGULATOR_BANK_WRITE | LDO_TEST_VPROG_UPDATE_MASK, + LDO_TEST_FINE_STEP_MASK | REGULATOR_BANK_MASK + | LDO_TEST_VPROG_UPDATE_MASK, + &vreg->test_reg[2]); +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int _pm8921_nldo1200_get_voltage(struct pm8921_vreg *vreg) +{ + int vprog, uV = 0; + + if (!NLDO1200_IN_ADVANCED_MODE(vreg)) { + pr_warn("%s: currently in legacy mode; voltage unknown.\n", + vreg->name); + return vreg->save_uV; + } + + vprog = vreg->ctrl_reg & NLDO1200_CTRL_VPROG_MASK; + + if ((vreg->ctrl_reg & NLDO1200_CTRL_RANGE_MASK) + == NLDO1200_CTRL_RANGE_LOW) + uV = vprog * NLDO1200_LOW_UV_STEP + NLDO1200_LOW_UV_MIN; + else + uV = vprog * NLDO1200_HIGH_UV_STEP + NLDO1200_HIGH_UV_MIN; + + return uV; +} + +static int pm8921_nldo1200_get_voltage(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + + return _pm8921_nldo1200_get_voltage(vreg); +} + +static int _pm8921_nldo1200_set_voltage(struct pm8921_vreg *vreg, int uV) +{ + u8 vprog, range; + int rc; + + if (uV < NLDO1200_LOW_UV_MIN || uV > NLDO1200_HIGH_UV_MAX) { + vreg_err(vreg, "requested voltage %d is outside of allowed " + "range.\n", uV); + return -EINVAL; + } + + if (uV < NLDO1200_HIGH_UV_MIN) { + vprog = ((uV - NLDO1200_LOW_UV_MIN) / NLDO1200_LOW_UV_STEP); + vprog &= NLDO1200_CTRL_VPROG_MASK; + range = NLDO1200_CTRL_RANGE_LOW; + } else { + vprog = ((uV - NLDO1200_HIGH_UV_MIN) / NLDO1200_HIGH_UV_STEP); + vprog &= NLDO1200_CTRL_VPROG_MASK; + range = NLDO1200_CTRL_RANGE_HIGH; + } + + /* Set to advanced mode */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + NLDO1200_ADVANCED_MODE, NLDO1200_ADVANCED_MODE_MASK, + &vreg->test_reg[2]); + if (rc) + goto bail; + + /* Set voltage and range selection. */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, vprog | range, + NLDO1200_CTRL_VPROG_MASK | NLDO1200_CTRL_RANGE_MASK, + &vreg->ctrl_reg); + if (rc) + goto bail; + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_nldo1200_set_voltage(struct regulator_dev *rdev, int min_uV, + int max_uV, unsigned *selector) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + + return _pm8921_nldo1200_set_voltage(vreg, min_uV); +} + +static int pm8921_smps_get_voltage_advanced(struct pm8921_vreg *vreg) +{ + u8 vprog, band; + int uV = 0; + + vprog = vreg->ctrl_reg & SMPS_ADVANCED_VPROG_MASK; + band = vreg->ctrl_reg & SMPS_ADVANCED_BAND_MASK; + + if (band == SMPS_ADVANCED_BAND_1) + uV = vprog * SMPS_BAND1_UV_STEP + SMPS_BAND1_UV_MIN; + else if (band == SMPS_ADVANCED_BAND_2) + uV = vprog * SMPS_BAND2_UV_STEP + SMPS_BAND2_UV_MIN; + else if (band == SMPS_ADVANCED_BAND_3) + uV = vprog * SMPS_BAND3_UV_STEP + SMPS_BAND3_UV_MIN; + else + uV = vreg->save_uV; + + return uV; +} + +static int pm8921_smps_get_voltage_legacy(struct pm8921_vreg *vreg) +{ + u8 vlow, vref, vprog; + int uV; + + vlow = vreg->test_reg[1] & SMPS_LEGACY_VLOW_SEL_MASK; + vref = vreg->ctrl_reg & SMPS_LEGACY_VREF_SEL_MASK; + vprog = vreg->ctrl_reg & SMPS_LEGACY_VPROG_MASK; + + if (vlow && vref) { + /* mode 3 */ + uV = vprog * SMPS_MODE3_UV_STEP + SMPS_MODE3_UV_MIN; + } else if (vref) { + /* mode 2 */ + uV = vprog * SMPS_MODE2_UV_STEP + SMPS_MODE2_UV_MIN; + } else { + /* mode 1 */ + uV = vprog * SMPS_MODE1_UV_STEP + SMPS_MODE1_UV_MIN; + } + + return uV; +} + +static int _pm8921_smps_get_voltage(struct pm8921_vreg *vreg) +{ + if (SMPS_IN_ADVANCED_MODE(vreg)) + return pm8921_smps_get_voltage_advanced(vreg); + + return pm8921_smps_get_voltage_legacy(vreg); +} + +static int pm8921_smps_get_voltage(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + + return _pm8921_smps_get_voltage(vreg); +} + +static int pm8921_smps_set_voltage_advanced(struct pm8921_vreg *vreg, int uV, + int force_on) +{ + u8 vprog, band; + int rc, new_uV; + + if (uV < SMPS_BAND1_UV_MIN || uV > SMPS_BAND3_UV_MAX) { + vreg_err(vreg, "requested voltage %d is outside of allowed " + "range.\n", uV); + return -EINVAL; + } + + if (uV < SMPS_BAND2_UV_MIN) { + vprog = ((uV - SMPS_BAND1_UV_MIN) / SMPS_BAND1_UV_STEP); + band = SMPS_ADVANCED_BAND_1; + new_uV = SMPS_BAND1_UV_MIN + vprog * SMPS_BAND1_UV_STEP; + } else if (uV < SMPS_BAND3_UV_MIN) { + vprog = ((uV - SMPS_BAND2_UV_MIN) / SMPS_BAND2_UV_STEP); + band = SMPS_ADVANCED_BAND_2; + new_uV = SMPS_BAND2_UV_MIN + vprog * SMPS_BAND2_UV_STEP; + } else { + vprog = ((uV - SMPS_BAND3_UV_MIN) / SMPS_BAND3_UV_STEP); + band = SMPS_ADVANCED_BAND_3; + new_uV = SMPS_BAND3_UV_MIN + vprog * SMPS_BAND3_UV_STEP; + } + + /* Do not set band if regulator currently disabled. */ + if (!_pm8921_vreg_is_enabled(vreg) && !force_on) + band = SMPS_ADVANCED_BAND_OFF; + + /* Set advanced mode bit to 1. */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, SMPS_ADVANCED_MODE + | REGULATOR_BANK_WRITE | REGULATOR_BANK_SEL(7), + SMPS_ADVANCED_MODE_MASK | REGULATOR_BANK_MASK, + &vreg->test_reg[7]); + if (rc) + goto bail; + + /* Set voltage and voltage band. */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, band | vprog, + SMPS_ADVANCED_BAND_MASK | SMPS_ADVANCED_VPROG_MASK, + &vreg->ctrl_reg); + if (rc) + goto bail; + + vreg->save_uV = new_uV; + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_smps_set_voltage_legacy(struct pm8921_vreg *vreg, int uV) +{ + u8 vlow, vref, vprog, pd, en; + int rc; + + if (uV < SMPS_MODE3_UV_MIN || uV > SMPS_MODE1_UV_MAX) { + vreg_err(vreg, "requested voltage %d is outside of allowed " + "range.\n", uV); + return -EINVAL; + } + + if (uV < SMPS_MODE2_UV_MIN) { + vprog = ((uV - SMPS_MODE3_UV_MIN) / SMPS_MODE3_UV_STEP); + vref = SMPS_LEGACY_VREF_SEL_MASK; + vlow = SMPS_LEGACY_VLOW_SEL_MASK; + } else if (uV < SMPS_MODE1_UV_MIN) { + vprog = ((uV - SMPS_MODE2_UV_MIN) / SMPS_MODE2_UV_STEP); + vref = SMPS_LEGACY_VREF_SEL_MASK; + vlow = 0; + } else { + vprog = ((uV - SMPS_MODE1_UV_MIN) / SMPS_MODE1_UV_STEP); + vref = 0; + vlow = 0; + } + + /* set vlow bit for ultra low voltage mode */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + vlow | REGULATOR_BANK_WRITE | REGULATOR_BANK_SEL(1), + REGULATOR_BANK_MASK | SMPS_LEGACY_VLOW_SEL_MASK, + &vreg->test_reg[1]); + if (rc) + goto bail; + + /* Set advanced mode bit to 0. */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, SMPS_LEGACY_MODE + | REGULATOR_BANK_WRITE | REGULATOR_BANK_SEL(7), + SMPS_ADVANCED_MODE_MASK | REGULATOR_BANK_MASK, + &vreg->test_reg[7]); + if (rc) + goto bail; + + en = (_pm8921_vreg_is_enabled(vreg) ? SMPS_LEGACY_ENABLE : 0); + pd = (vreg->pdata.pull_down_enable ? SMPS_LEGACY_PULL_DOWN_ENABLE : 0); + + /* Set voltage (and the rest of the control register). */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, en | pd | vref | vprog, + SMPS_LEGACY_ENABLE | SMPS_LEGACY_PULL_DOWN_ENABLE + | SMPS_LEGACY_VREF_SEL_MASK | SMPS_LEGACY_VPROG_MASK, + &vreg->ctrl_reg); + + vreg->save_uV = pm8921_smps_get_voltage_legacy(vreg); + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_smps_set_voltage(struct regulator_dev *rdev, int min_uV, + int max_uV, unsigned *selector) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + int rc = 0; + + if (SMPS_IN_ADVANCED_MODE(vreg) || !pm8921_vreg_is_pin_controlled(vreg)) + rc = pm8921_smps_set_voltage_advanced(vreg, min_uV, 0); + else + rc = pm8921_smps_set_voltage_legacy(vreg, min_uV); + + return rc; +} + +static int _pm8921_ftsmps_get_voltage(struct pm8921_vreg *vreg) +{ + u8 vprog, band; + int uV = 0; + + if ((vreg->test_reg[0] & FTSMPS_CNFG1_PM_MASK) == FTSMPS_CNFG1_PM_PFM) { + vprog = vreg->pfm_ctrl_reg & FTSMPS_VCTRL_VPROG_MASK; + band = vreg->pfm_ctrl_reg & FTSMPS_VCTRL_BAND_MASK; + if (band == FTSMPS_VCTRL_BAND_OFF && vprog == 0) { + /* PWM_VCTRL overrides PFM_VCTRL */ + vprog = vreg->ctrl_reg & FTSMPS_VCTRL_VPROG_MASK; + band = vreg->ctrl_reg & FTSMPS_VCTRL_BAND_MASK; + } + } else { + vprog = vreg->ctrl_reg & FTSMPS_VCTRL_VPROG_MASK; + band = vreg->ctrl_reg & FTSMPS_VCTRL_BAND_MASK; + } + + if (band == FTSMPS_VCTRL_BAND_1) + uV = vprog * FTSMPS_BAND1_UV_STEP + FTSMPS_BAND1_UV_MIN; + else if (band == FTSMPS_VCTRL_BAND_2) + uV = vprog * FTSMPS_BAND2_UV_STEP + FTSMPS_BAND2_UV_MIN; + else if (band == FTSMPS_VCTRL_BAND_3) + uV = vprog * FTSMPS_BAND3_UV_STEP + FTSMPS_BAND3_UV_MIN; + else + uV = vreg->save_uV; + + return uV; +} + +static int pm8921_ftsmps_get_voltage(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + + return _pm8921_ftsmps_get_voltage(vreg); +} + +static int _pm8921_ftsmps_set_voltage(struct pm8921_vreg *vreg, int uV, + int force_on) +{ + int rc, new_uV; + u8 vprog, band; + + if (uV < FTSMPS_BAND1_UV_MIN || uV > FTSMPS_BAND3_UV_MAX) { + vreg_err(vreg, "requested voltage %d is outside of allowed " + "range.\n", uV); + return -EINVAL; + } + + /* Round down for set points in the gaps between bands. */ + if (uV > FTSMPS_BAND1_UV_MAX && uV < FTSMPS_BAND2_UV_MIN) + uV = FTSMPS_BAND1_UV_MAX; + else if (uV > FTSMPS_BAND2_UV_MAX + && uV < FTSMPS_BAND3_UV_SETPOINT_MIN) + uV = FTSMPS_BAND2_UV_MAX; + + if (uV < FTSMPS_BAND2_UV_MIN) { + vprog = ((uV - FTSMPS_BAND1_UV_MIN) / FTSMPS_BAND1_UV_STEP); + vprog = PM8921_FTSMPS_BAND_1_COMPENSATE(vprog); + band = FTSMPS_VCTRL_BAND_1; + new_uV = FTSMPS_BAND1_UV_MIN + vprog * FTSMPS_BAND1_UV_STEP; + } else if (uV < FTSMPS_BAND3_UV_SETPOINT_MIN) { + vprog = ((uV - FTSMPS_BAND2_UV_MIN) / FTSMPS_BAND2_UV_STEP); + band = FTSMPS_VCTRL_BAND_2; + new_uV = FTSMPS_BAND2_UV_MIN + vprog * FTSMPS_BAND2_UV_STEP; + } else { + vprog = ((uV - FTSMPS_BAND3_UV_MIN) / FTSMPS_BAND3_UV_STEP); + band = FTSMPS_VCTRL_BAND_3; + new_uV = FTSMPS_BAND3_UV_MIN + vprog * FTSMPS_BAND3_UV_STEP; + } + + /* + * Do not set voltage if regulator is currently disabled because doing + * so will enable it. + */ + if (_pm8921_vreg_is_enabled(vreg) || force_on) { + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, band | vprog, + FTSMPS_VCTRL_BAND_MASK | FTSMPS_VCTRL_VPROG_MASK, + &vreg->ctrl_reg); + if (rc) + goto bail; + + /* Program PFM_VCTRL as 0x00 so that PWM_VCTRL overrides it. */ + rc = pm8921_vreg_write(vreg, vreg->pfm_ctrl_addr, 0x00, + FTSMPS_VCTRL_BAND_MASK | FTSMPS_VCTRL_VPROG_MASK, + &vreg->pfm_ctrl_reg); + if (rc) + goto bail; + } + + vreg->save_uV = new_uV; + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_ftsmps_set_voltage(struct regulator_dev *rdev, int min_uV, + int max_uV, unsigned *selector) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + + return _pm8921_ftsmps_set_voltage(vreg, min_uV, 0); +} + +static int pm8921_ncp_get_voltage(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + u8 vprog; + + vprog = vreg->ctrl_reg & NCP_VPROG_MASK; + + return NCP_UV_MIN + vprog * NCP_UV_STEP; +} + +static int pm8921_ncp_set_voltage(struct regulator_dev *rdev, int min_uV, + int max_uV, unsigned *selector) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + int rc; + u8 val; + + if (min_uV < NCP_UV_MIN || min_uV > NCP_UV_MAX) { + vreg_err(vreg, "requested voltage %d is outside of allowed " + "range.\n", min_uV); + return -EINVAL; + } + + val = (min_uV - NCP_UV_MIN) / NCP_UV_STEP; + + /* voltage setting */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, val, NCP_VPROG_MASK, + &vreg->ctrl_reg); + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_vreg_set_pin_ctrl(struct pm8921_vreg *vreg, int on) +{ + int rc = 0, bank; + u8 val = 0, mask; + unsigned pc = vreg->pdata.pin_ctrl, pf = vreg->pdata.pin_fn; + + switch (vreg->type) { + case REGULATOR_TYPE_LDO: + if (on) { + if (pc & PM8921_VREG_PIN_CTRL_D0) + val |= LDO_TEST_PIN_CTRL_EN0; + if (pc & PM8921_VREG_PIN_CTRL_D1) + val |= LDO_TEST_PIN_CTRL_EN1; + if (pc & PM8921_VREG_PIN_CTRL_A0) + val |= LDO_TEST_PIN_CTRL_EN2; + if (pc & PM8921_VREG_PIN_CTRL_A1) + val |= LDO_TEST_PIN_CTRL_EN3; + + bank = (pf == PM8921_VREG_PIN_FN_ENABLE ? 5 : 6); + rc = pm8921_vreg_write(vreg, vreg->test_addr, + val | REGULATOR_BANK_SEL(bank) + | REGULATOR_BANK_WRITE, + LDO_TEST_PIN_CTRL_MASK | REGULATOR_BANK_MASK, + &vreg->test_reg[bank]); + if (rc) + goto bail; + + val = LDO_TEST_LPM_SEL_CTRL | REGULATOR_BANK_WRITE + | REGULATOR_BANK_SEL(0); + mask = LDO_TEST_LPM_MASK | REGULATOR_BANK_MASK; + rc = pm8921_vreg_write(vreg, vreg->test_addr, val, mask, + &vreg->test_reg[0]); + if (rc) + goto bail; + + if (pf == PM8921_VREG_PIN_FN_ENABLE) { + /* Pin control ON/OFF */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + LDO_CTRL_PM_HPM, + LDO_ENABLE_MASK | LDO_CTRL_PM_MASK, + &vreg->ctrl_reg); + if (rc) + goto bail; + } else { + /* Pin control LPM/HPM */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + LDO_ENABLE | LDO_CTRL_PM_LPM, + LDO_ENABLE_MASK | LDO_CTRL_PM_MASK, + &vreg->ctrl_reg); + if (rc) + goto bail; + } + } else { + /* Pin control off */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + REGULATOR_BANK_SEL(5) | REGULATOR_BANK_WRITE, + LDO_TEST_PIN_CTRL_MASK | REGULATOR_BANK_MASK, + &vreg->test_reg[5]); + if (rc) + goto bail; + + rc = pm8921_vreg_write(vreg, vreg->test_addr, + REGULATOR_BANK_SEL(6) | REGULATOR_BANK_WRITE, + LDO_TEST_PIN_CTRL_MASK | REGULATOR_BANK_MASK, + &vreg->test_reg[6]); + if (rc) + goto bail; + } + break; + + case REGULATOR_TYPE_SMPS: + if (on) { + if (pf == PM8921_VREG_PIN_FN_ENABLE) { + /* Pin control ON/OFF */ + if (pc & PM8921_VREG_PIN_CTRL_D0) + val |= SMPS_PIN_CTRL_D0; + if (pc & PM8921_VREG_PIN_CTRL_D1) + val |= SMPS_PIN_CTRL_D1; + if (pc & PM8921_VREG_PIN_CTRL_A0) + val |= SMPS_PIN_CTRL_A0; + if (pc & PM8921_VREG_PIN_CTRL_A1) + val |= SMPS_PIN_CTRL_A1; + } else { + /* Pin control LPM/HPM */ + if (pc & PM8921_VREG_PIN_CTRL_D0) + val |= SMPS_PIN_CTRL_LPM_D0; + if (pc & PM8921_VREG_PIN_CTRL_D1) + val |= SMPS_PIN_CTRL_LPM_D1; + if (pc & PM8921_VREG_PIN_CTRL_A0) + val |= SMPS_PIN_CTRL_LPM_A0; + if (pc & PM8921_VREG_PIN_CTRL_A1) + val |= SMPS_PIN_CTRL_LPM_A1; + } + + rc = pm8921_smps_set_voltage_legacy(vreg, + vreg->save_uV); + if (rc) + goto bail; + + rc = pm8921_vreg_write(vreg, vreg->sleep_ctrl_addr, val, + SMPS_PIN_CTRL_MASK | SMPS_PIN_CTRL_LPM_MASK, + &vreg->sleep_ctrl_reg); + if (rc) + goto bail; + + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + (pf == PM8921_VREG_PIN_FN_ENABLE + ? 0 : SMPS_LEGACY_ENABLE), + SMPS_LEGACY_ENABLE, &vreg->ctrl_reg); + if (rc) + goto bail; + + rc = pm8921_vreg_write(vreg, vreg->clk_ctrl_addr, + (pf == PM8921_VREG_PIN_FN_ENABLE + ? SMPS_CLK_CTRL_PWM : SMPS_CLK_CTRL_PFM), + SMPS_CLK_CTRL_MASK, &vreg->clk_ctrl_reg); + if (rc) + goto bail; + } else { + /* Pin control off */ + if (!SMPS_IN_ADVANCED_MODE(vreg)) { + if (_pm8921_vreg_is_enabled(vreg)) + val = SMPS_LEGACY_ENABLE; + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + val, SMPS_LEGACY_ENABLE, + &vreg->ctrl_reg); + if (rc) + goto bail; + } + + rc = pm8921_vreg_write(vreg, vreg->sleep_ctrl_addr, 0, + SMPS_PIN_CTRL_MASK | SMPS_PIN_CTRL_LPM_MASK, + &vreg->sleep_ctrl_reg); + if (rc) + goto bail; + + rc = pm8921_smps_set_voltage_advanced(vreg, + vreg->save_uV, 0); + if (rc) + goto bail; + } + break; + + case REGULATOR_TYPE_VS: + if (on) { + if (pc & PM8921_VREG_PIN_CTRL_D0) + val |= VS_PIN_CTRL_EN0; + if (pc & PM8921_VREG_PIN_CTRL_D1) + val |= VS_PIN_CTRL_EN1; + if (pc & PM8921_VREG_PIN_CTRL_A0) + val |= VS_PIN_CTRL_EN2; + if (pc & PM8921_VREG_PIN_CTRL_A1) + val |= VS_PIN_CTRL_EN3; + + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, val, + VS_PIN_CTRL_MASK | VS_ENABLE_MASK, + &vreg->ctrl_reg); + if (rc) + goto bail; + } else { + /* Pin control off */ + if (_pm8921_vreg_is_enabled(vreg)) + val = VS_ENABLE; + + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, val, + VS_ENABLE_MASK | VS_PIN_CTRL_MASK, + &vreg->ctrl_reg); + if (rc) + goto bail; + } + break; + } + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static unsigned int pm8921_vreg_get_mode(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + + /* Check physical pin control state. */ + switch (vreg->type) { + case REGULATOR_TYPE_LDO: + if (!(vreg->ctrl_reg & LDO_ENABLE_MASK) + && (vreg->test_reg[5] & LDO_TEST_PIN_CTRL_MASK)) + return REGULATOR_MODE_IDLE; + else if ((vreg->ctrl_reg & LDO_ENABLE_MASK) + && (vreg->ctrl_reg & LDO_CTRL_PM_MASK) + && (vreg->test_reg[6] & LDO_TEST_PIN_CTRL_LPM_MASK)) + return REGULATOR_MODE_IDLE; + break; + case REGULATOR_TYPE_SMPS: + if (!SMPS_IN_ADVANCED_MODE(vreg) + && !(vreg->ctrl_reg & SMPS_LEGACY_ENABLE) + && (vreg->sleep_ctrl_reg & SMPS_PIN_CTRL_MASK)) + return REGULATOR_MODE_IDLE; + else if (!SMPS_IN_ADVANCED_MODE(vreg) + && (vreg->ctrl_reg & SMPS_LEGACY_ENABLE) + && ((vreg->clk_ctrl_reg & SMPS_CLK_CTRL_MASK) + == SMPS_CLK_CTRL_PFM) + && (vreg->sleep_ctrl_reg & SMPS_PIN_CTRL_LPM_MASK)) + return REGULATOR_MODE_IDLE; + break; + case REGULATOR_TYPE_VS: + if (!(vreg->ctrl_reg & VS_ENABLE_MASK) + && (vreg->ctrl_reg & VS_PIN_CTRL_MASK)) + return REGULATOR_MODE_IDLE; + } + + if (vreg->optimum == REGULATOR_MODE_FAST) + return REGULATOR_MODE_FAST; + else if (vreg->pc_vote) + return REGULATOR_MODE_IDLE; + else if (vreg->optimum == REGULATOR_MODE_STANDBY) + return REGULATOR_MODE_STANDBY; + return REGULATOR_MODE_FAST; +} + +static int pm8921_ldo_set_mode(struct pm8921_vreg *vreg, unsigned int mode) +{ + int rc = 0; + u8 mask, val; + + switch (mode) { + case REGULATOR_MODE_FAST: + /* HPM */ + val = (_pm8921_vreg_is_enabled(vreg) ? LDO_ENABLE : 0) + | LDO_CTRL_PM_HPM; + mask = LDO_ENABLE_MASK | LDO_CTRL_PM_MASK; + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, val, mask, + &vreg->ctrl_reg); + if (rc) + goto bail; + + if (pm8921_vreg_is_pin_controlled(vreg)) + rc = pm8921_vreg_set_pin_ctrl(vreg, 0); + if (rc) + goto bail; + break; + + case REGULATOR_MODE_STANDBY: + /* LPM */ + val = (_pm8921_vreg_is_enabled(vreg) ? LDO_ENABLE : 0) + | LDO_CTRL_PM_LPM; + mask = LDO_ENABLE_MASK | LDO_CTRL_PM_MASK; + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, val, mask, + &vreg->ctrl_reg); + if (rc) + goto bail; + + val = LDO_TEST_LPM_SEL_CTRL | REGULATOR_BANK_WRITE + | REGULATOR_BANK_SEL(0); + mask = LDO_TEST_LPM_MASK | REGULATOR_BANK_MASK; + rc = pm8921_vreg_write(vreg, vreg->test_addr, val, mask, + &vreg->test_reg[0]); + if (rc) + goto bail; + + if (pm8921_vreg_is_pin_controlled(vreg)) + rc = pm8921_vreg_set_pin_ctrl(vreg, 0); + if (rc) + goto bail; + break; + + case REGULATOR_MODE_IDLE: + /* Pin Control */ + if (_pm8921_vreg_is_enabled(vreg)) + rc = pm8921_vreg_set_pin_ctrl(vreg, 1); + if (rc) + goto bail; + break; + + default: + vreg_err(vreg, "invalid mode: %u\n", mode); + return -EINVAL; + } + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_nldo1200_set_mode(struct pm8921_vreg *vreg, unsigned int mode) +{ + int rc = 0; + + if (mode != REGULATOR_MODE_FAST && mode != REGULATOR_MODE_STANDBY) { + vreg_err(vreg, "invalid mode: %u\n", mode); + return -EINVAL; + } + + /* + * Make sure that advanced mode is in use. If it isn't, then set it + * and update the voltage accordingly. + */ + if (!NLDO1200_IN_ADVANCED_MODE(vreg)) { + rc = pm8921_vreg_write(vreg, vreg->test_addr, + NLDO1200_ADVANCED_MODE, NLDO1200_ADVANCED_MODE_MASK, + &vreg->test_reg[2]); + if (rc) + goto bail; + + _pm8921_nldo1200_set_voltage(vreg, vreg->save_uV); + } + + if (mode == REGULATOR_MODE_FAST) { + /* HPM */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + NLDO1200_ADVANCED_PM_HPM, NLDO1200_ADVANCED_PM_MASK, + &vreg->test_reg[2]); + } else { + /* LPM */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + NLDO1200_ADVANCED_PM_LPM, NLDO1200_ADVANCED_PM_MASK, + &vreg->test_reg[2]); + } + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_smps_set_mode(struct pm8921_vreg *vreg, unsigned int mode) +{ + int rc = 0; + + switch (mode) { + case REGULATOR_MODE_FAST: + /* HPM */ + rc = pm8921_vreg_write(vreg, vreg->clk_ctrl_addr, + SMPS_CLK_CTRL_PWM, SMPS_CLK_CTRL_MASK, + &vreg->clk_ctrl_reg); + if (rc) + goto bail; + + if (pm8921_vreg_is_pin_controlled(vreg)) + rc = pm8921_vreg_set_pin_ctrl(vreg, 0); + if (rc) + goto bail; + break; + + case REGULATOR_MODE_STANDBY: + /* LPM */ + rc = pm8921_vreg_write(vreg, vreg->clk_ctrl_addr, + SMPS_CLK_CTRL_PFM, SMPS_CLK_CTRL_MASK, + &vreg->clk_ctrl_reg); + if (rc) + goto bail; + + if (pm8921_vreg_is_pin_controlled(vreg)) + rc = pm8921_vreg_set_pin_ctrl(vreg, 0); + if (rc) + goto bail; + break; + + case REGULATOR_MODE_IDLE: + /* Pin Control */ + if (_pm8921_vreg_is_enabled(vreg)) + rc = pm8921_vreg_set_pin_ctrl(vreg, 1); + if (rc) + goto bail; + break; + + default: + vreg_err(vreg, "invalid mode: %u\n", mode); + return -EINVAL; + } + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_ftsmps_set_mode(struct pm8921_vreg *vreg, unsigned int mode) +{ + int rc = 0; + + if (mode == REGULATOR_MODE_FAST) { + /* HPM */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + FTSMPS_CNFG1_PM_PWM, FTSMPS_CNFG1_PM_MASK, + &vreg->test_reg[0]); + } else if (mode == REGULATOR_MODE_STANDBY) { + /* LPM */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + FTSMPS_CNFG1_PM_PFM, FTSMPS_CNFG1_PM_MASK, + &vreg->test_reg[0]); + } else { + vreg_err(vreg, "invalid mode: %u\n", mode); + return -EINVAL; + } + + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_lvs_set_mode(struct pm8921_vreg *vreg, unsigned int mode) +{ + int rc = 0; + + if (mode == REGULATOR_MODE_IDLE) { + /* Use pin control. */ + if (_pm8921_vreg_is_enabled(vreg)) + rc = pm8921_vreg_set_pin_ctrl(vreg, 1); + } else { + /* Turn off pin control. */ + rc = pm8921_vreg_set_pin_ctrl(vreg, 0); + } + + return rc; +} + +/* + * Optimum mode programming: + * REGULATOR_MODE_FAST: Go to HPM (highest priority) + * REGULATOR_MODE_STANDBY: Go to pin ctrl mode if there are any pin ctrl + * votes, else go to LPM + * + * Pin ctrl mode voting via regulator set_mode: + * REGULATOR_MODE_IDLE: Go to pin ctrl mode if the optimum mode is LPM, else + * go to HPM + * REGULATOR_MODE_NORMAL: Go to LPM if it is the optimum mode, else go to HPM + */ +static int pm8921_vreg_set_mode(struct regulator_dev *rdev, unsigned int mode) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + unsigned prev_optimum = vreg->optimum, prev_pc_vote = vreg->pc_vote; + int rc = 0, new_mode = REGULATOR_MODE_FAST; + + /* Determine new mode to go into. */ + switch (mode) { + case REGULATOR_MODE_FAST: + new_mode = REGULATOR_MODE_FAST; + vreg->optimum = mode; + break; + + case REGULATOR_MODE_STANDBY: + if (vreg->pc_vote) + new_mode = REGULATOR_MODE_IDLE; + else + new_mode = REGULATOR_MODE_STANDBY; + vreg->optimum = mode; + break; + + case REGULATOR_MODE_IDLE: + if (vreg->pc_vote++) + return rc; /* already taken care of */ + + if (vreg->optimum == REGULATOR_MODE_FAST) + new_mode = REGULATOR_MODE_FAST; + else + new_mode = REGULATOR_MODE_IDLE; + break; + + case REGULATOR_MODE_NORMAL: + if (vreg->pc_vote && --(vreg->pc_vote)) + return rc; /* already taken care of */ + + if (vreg->optimum == REGULATOR_MODE_STANDBY) + new_mode = REGULATOR_MODE_STANDBY; + else + new_mode = REGULATOR_MODE_FAST; + break; + + default: + vreg_err(vreg, "unknown mode, mode=%u\n", mode); + return -EINVAL; + } + + switch (vreg->type) { + case REGULATOR_TYPE_LDO: + rc = pm8921_ldo_set_mode(vreg, new_mode); + break; + case REGULATOR_TYPE_NLDO1200: + rc = pm8921_nldo1200_set_mode(vreg, new_mode); + break; + case REGULATOR_TYPE_SMPS: + rc = pm8921_smps_set_mode(vreg, new_mode); + break; + case REGULATOR_TYPE_FTSMPS: + rc = pm8921_ftsmps_set_mode(vreg, new_mode); + break; + case REGULATOR_TYPE_VS: + rc = pm8921_lvs_set_mode(vreg, new_mode); + break; + } + + if (rc) { + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + vreg->optimum = prev_optimum; + vreg->pc_vote = prev_pc_vote; + } + + return rc; +} + +static unsigned int pm8921_vreg_get_optimum_mode(struct regulator_dev *rdev, + int input_uV, int output_uV, int load_uA) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + + vreg->save_uA = load_uA; + + if (load_uA >= vreg->hpm_min_load) + return REGULATOR_MODE_FAST; + + return REGULATOR_MODE_STANDBY; +} + +static int pm8921_vreg_enable(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + int mode, rc = 0; + + mode = pm8921_vreg_get_mode(rdev); + + if (mode == REGULATOR_MODE_IDLE) { + /* Turn on pin control. */ + rc = pm8921_vreg_set_pin_ctrl(vreg, 1); + if (rc) + goto bail; + return rc; + } + /* + * All regulator types except advanced mode SMPS, FTSMPS, and VS300 have + * enable bit in bit 7 of the control register. + */ + switch (vreg->type) { + case REGULATOR_TYPE_SMPS: + if (SMPS_IN_ADVANCED_MODE(vreg) + || !pm8921_vreg_is_pin_controlled(vreg)) { + /* Enable in advanced mode if not using pin control. */ + rc = pm8921_smps_set_voltage_advanced(vreg, + vreg->save_uV, 1); + } else { + /* Leave in legacy mode because pin control is used. */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + SMPS_LEGACY_ENABLE, SMPS_LEGACY_ENABLE, + &vreg->ctrl_reg); + } + break; + case REGULATOR_TYPE_FTSMPS: + rc = _pm8921_ftsmps_set_voltage(vreg, vreg->save_uV, 1); + break; + case REGULATOR_TYPE_VS300: + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, VS300_CTRL_ENABLE, + VS300_CTRL_ENABLE_MASK, &vreg->ctrl_reg); + break; + default: + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, REGULATOR_ENABLE, + REGULATOR_ENABLE_MASK, &vreg->ctrl_reg); + } + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_vreg_disable(struct regulator_dev *rdev) +{ + struct pm8921_vreg *vreg = rdev_get_drvdata(rdev); + int rc = 0; + + /* Turn off pin control. */ + rc = pm8921_vreg_set_pin_ctrl(vreg, 0); + if (rc) + goto bail; + + /* Disable in local control register. */ + if (vreg->type == REGULATOR_TYPE_SMPS && SMPS_IN_ADVANCED_MODE(vreg)) { + /* Change SMPS to legacy mode before disabling. */ + rc = pm8921_smps_set_voltage_legacy(vreg, vreg->save_uV); + if (rc) + goto bail; + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, REGULATOR_DISABLE, + REGULATOR_ENABLE_MASK, &vreg->ctrl_reg); + } else if (vreg->type == REGULATOR_TYPE_FTSMPS) { + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + FTSMPS_VCTRL_BAND_OFF, FTSMPS_VCTRL_BAND_MASK, + &vreg->ctrl_reg); + if (rc) + goto bail; + rc = pm8921_vreg_write(vreg, vreg->pfm_ctrl_addr, + FTSMPS_VCTRL_BAND_OFF, FTSMPS_VCTRL_BAND_MASK, + &vreg->pfm_ctrl_reg); + } else if (vreg->type == REGULATOR_TYPE_VS300) { + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + VS300_CTRL_DISABLE, VS300_CTRL_ENABLE_MASK, + &vreg->ctrl_reg); + } else { + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, REGULATOR_DISABLE, + REGULATOR_ENABLE_MASK, &vreg->ctrl_reg); + } + +bail: + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static struct regulator_ops pm8921_pldo_ops = { + .enable = pm8921_vreg_enable, + .disable = pm8921_vreg_disable, + .is_enabled = pm8921_vreg_is_enabled, + .set_voltage = pm8921_pldo_set_voltage, + .get_voltage = pm8921_pldo_get_voltage, + .set_mode = pm8921_vreg_set_mode, + .get_mode = pm8921_vreg_get_mode, + .get_optimum_mode = pm8921_vreg_get_optimum_mode, +}; + +static struct regulator_ops pm8921_nldo_ops = { + .enable = pm8921_vreg_enable, + .disable = pm8921_vreg_disable, + .is_enabled = pm8921_vreg_is_enabled, + .set_voltage = pm8921_nldo_set_voltage, + .get_voltage = pm8921_nldo_get_voltage, + .set_mode = pm8921_vreg_set_mode, + .get_mode = pm8921_vreg_get_mode, + .get_optimum_mode = pm8921_vreg_get_optimum_mode, +}; + +static struct regulator_ops pm8921_nldo1200_ops = { + .enable = pm8921_vreg_enable, + .disable = pm8921_vreg_disable, + .is_enabled = pm8921_vreg_is_enabled, + .set_voltage = pm8921_nldo1200_set_voltage, + .get_voltage = pm8921_nldo1200_get_voltage, + .set_mode = pm8921_vreg_set_mode, + .get_mode = pm8921_vreg_get_mode, + .get_optimum_mode = pm8921_vreg_get_optimum_mode, +}; + +static struct regulator_ops pm8921_smps_ops = { + .enable = pm8921_vreg_enable, + .disable = pm8921_vreg_disable, + .is_enabled = pm8921_vreg_is_enabled, + .set_voltage = pm8921_smps_set_voltage, + .get_voltage = pm8921_smps_get_voltage, + .set_mode = pm8921_vreg_set_mode, + .get_mode = pm8921_vreg_get_mode, + .get_optimum_mode = pm8921_vreg_get_optimum_mode, +}; + +static struct regulator_ops pm8921_ftsmps_ops = { + .enable = pm8921_vreg_enable, + .disable = pm8921_vreg_disable, + .is_enabled = pm8921_vreg_is_enabled, + .set_voltage = pm8921_ftsmps_set_voltage, + .get_voltage = pm8921_ftsmps_get_voltage, + .set_mode = pm8921_vreg_set_mode, + .get_mode = pm8921_vreg_get_mode, + .get_optimum_mode = pm8921_vreg_get_optimum_mode, +}; + +static struct regulator_ops pm8921_vs_ops = { + .enable = pm8921_vreg_enable, + .disable = pm8921_vreg_disable, + .is_enabled = pm8921_vreg_is_enabled, + .set_mode = pm8921_vreg_set_mode, + .get_mode = pm8921_vreg_get_mode, +}; + +static struct regulator_ops pm8921_vs300_ops = { + .enable = pm8921_vreg_enable, + .disable = pm8921_vreg_disable, + .is_enabled = pm8921_vreg_is_enabled, +}; + +static struct regulator_ops pm8921_ncp_ops = { + .enable = pm8921_vreg_enable, + .disable = pm8921_vreg_disable, + .is_enabled = pm8921_vreg_is_enabled, + .set_voltage = pm8921_ncp_set_voltage, + .get_voltage = pm8921_ncp_get_voltage, +}; + +#define VREG_DESC(_id, _name, _ops) \ + [PM8921_VREG_ID_##_id] = { \ + .id = PM8921_VREG_ID_##_id, \ + .name = _name, \ + .ops = _ops, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + } + +static struct regulator_desc pm8921_vreg_description[] = { + VREG_DESC(L1, "8921_l1", &pm8921_nldo_ops), + VREG_DESC(L2, "8921_l2", &pm8921_nldo_ops), + VREG_DESC(L3, "8921_l3", &pm8921_pldo_ops), + VREG_DESC(L4, "8921_l4", &pm8921_pldo_ops), + VREG_DESC(L5, "8921_l5", &pm8921_pldo_ops), + VREG_DESC(L6, "8921_l6", &pm8921_pldo_ops), + VREG_DESC(L7, "8921_l7", &pm8921_pldo_ops), + VREG_DESC(L8, "8921_l8", &pm8921_pldo_ops), + VREG_DESC(L9, "8921_l9", &pm8921_pldo_ops), + VREG_DESC(L10, "8921_l10", &pm8921_pldo_ops), + VREG_DESC(L11, "8921_l11", &pm8921_pldo_ops), + VREG_DESC(L12, "8921_l12", &pm8921_nldo_ops), + VREG_DESC(L14, "8921_l14", &pm8921_pldo_ops), + VREG_DESC(L15, "8921_l15", &pm8921_pldo_ops), + VREG_DESC(L16, "8921_l16", &pm8921_pldo_ops), + VREG_DESC(L17, "8921_l17", &pm8921_pldo_ops), + VREG_DESC(L18, "8921_l18", &pm8921_nldo_ops), + VREG_DESC(L21, "8921_l21", &pm8921_pldo_ops), + VREG_DESC(L22, "8921_l22", &pm8921_pldo_ops), + VREG_DESC(L23, "8921_l23", &pm8921_pldo_ops), + VREG_DESC(L24, "8921_l24", &pm8921_nldo1200_ops), + VREG_DESC(L25, "8921_l25", &pm8921_nldo1200_ops), + VREG_DESC(L26, "8921_l26", &pm8921_nldo1200_ops), + VREG_DESC(L27, "8921_l27", &pm8921_nldo1200_ops), + VREG_DESC(L28, "8921_l28", &pm8921_nldo1200_ops), + VREG_DESC(L29, "8921_l29", &pm8921_pldo_ops), + + VREG_DESC(S1, "8921_s1", &pm8921_smps_ops), + VREG_DESC(S2, "8921_s2", &pm8921_smps_ops), + VREG_DESC(S3, "8921_s3", &pm8921_smps_ops), + VREG_DESC(S4, "8921_s4", &pm8921_smps_ops), + VREG_DESC(S5, "8921_s5", &pm8921_ftsmps_ops), + VREG_DESC(S6, "8921_s6", &pm8921_ftsmps_ops), + VREG_DESC(S7, "8921_s7", &pm8921_smps_ops), + VREG_DESC(S8, "8921_s8", &pm8921_smps_ops), + + VREG_DESC(LVS1, "8921_lvs1", &pm8921_vs_ops), + VREG_DESC(LVS2, "8921_lvs2", &pm8921_vs300_ops), + VREG_DESC(LVS3, "8921_lvs3", &pm8921_vs_ops), + VREG_DESC(LVS4, "8921_lvs4", &pm8921_vs_ops), + VREG_DESC(LVS5, "8921_lvs5", &pm8921_vs_ops), + VREG_DESC(LVS6, "8921_lvs6", &pm8921_vs_ops), + VREG_DESC(LVS7, "8921_lvs7", &pm8921_vs_ops), + + VREG_DESC(USB_OTG, "8921_usb_otg", &pm8921_vs300_ops), + VREG_DESC(HDMI_MVS, "8921_hdmi_mvs", &pm8921_vs300_ops), + VREG_DESC(NCP, "8921_ncp", &pm8921_ncp_ops), +}; + +static int pm8921_init_ldo(struct pm8921_vreg *vreg) +{ + int rc = 0, i; + u8 bank; + + /* Save the current test register state. */ + for (i = 0; i < LDO_TEST_BANKS; i++) { + bank = REGULATOR_BANK_SEL(i); + rc = pm8xxx_writeb(vreg->dev->parent, vreg->test_addr, bank); + if (rc) + goto bail; + + rc = pm8xxx_readb(vreg->dev->parent, vreg->test_addr, + &vreg->test_reg[i]); + if (rc) + goto bail; + vreg->test_reg[i] |= REGULATOR_BANK_WRITE; + } + + if ((vreg->ctrl_reg & LDO_CTRL_PM_MASK) == LDO_CTRL_PM_LPM) + vreg->optimum = REGULATOR_MODE_STANDBY; + else + vreg->optimum = REGULATOR_MODE_FAST; + + /* Set pull down enable based on platform data. */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + (vreg->pdata.pull_down_enable ? LDO_PULL_DOWN_ENABLE : 0), + LDO_PULL_DOWN_ENABLE_MASK, &vreg->ctrl_reg); +bail: + if (rc) + vreg_err(vreg, "pm8xxx_readb/writeb failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_init_nldo1200(struct pm8921_vreg *vreg) +{ + int rc = 0, i; + u8 bank; + + /* Save the current test register state. */ + for (i = 0; i < LDO_TEST_BANKS; i++) { + bank = REGULATOR_BANK_SEL(i); + rc = pm8xxx_writeb(vreg->dev->parent, vreg->test_addr, bank); + if (rc) + goto bail; + + rc = pm8xxx_readb(vreg->dev->parent, vreg->test_addr, + &vreg->test_reg[i]); + if (rc) + goto bail; + vreg->test_reg[i] |= REGULATOR_BANK_WRITE; + } + + /* + * get_voltage must return >0 in order for regulator_set_optimum_mode + * to succeed, but voltage may be unknown at probe time. + */ + vreg->save_uV = 1; /* This is not a no-op. */ + vreg->save_uV = _pm8921_nldo1200_get_voltage(vreg); + + if (NLDO1200_IN_ADVANCED_MODE(vreg)) { + if ((vreg->test_reg[2] & NLDO1200_ADVANCED_PM_MASK) + == NLDO1200_ADVANCED_PM_LPM) + vreg->optimum = REGULATOR_MODE_STANDBY; + else + vreg->optimum = REGULATOR_MODE_FAST; + } else { + if ((vreg->ctrl_reg & NLDO1200_LEGACY_PM_MASK) + == NLDO1200_LEGACY_PM_LPM) + vreg->optimum = REGULATOR_MODE_STANDBY; + else + vreg->optimum = REGULATOR_MODE_FAST; + } + + /* Set pull down enable based on platform data. */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + (vreg->pdata.pull_down_enable ? NLDO1200_PULL_DOWN_ENABLE : 0), + NLDO1200_PULL_DOWN_ENABLE_MASK, &vreg->test_reg[1]); +bail: + if (rc) + vreg_err(vreg, "pm8xxx_readb/writeb failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_init_smps(struct pm8921_vreg *vreg) +{ + int rc = 0, i; + u8 bank; + + /* Save the current test2 register state. */ + for (i = 0; i < SMPS_TEST_BANKS; i++) { + bank = REGULATOR_BANK_SEL(i); + rc = pm8xxx_writeb(vreg->dev->parent, vreg->test_addr, bank); + if (rc) + goto bail; + + rc = pm8xxx_readb(vreg->dev->parent, vreg->test_addr, + &vreg->test_reg[i]); + if (rc) + goto bail; + vreg->test_reg[i] |= REGULATOR_BANK_WRITE; + } + + /* Save the current clock control register state. */ + rc = pm8xxx_readb(vreg->dev->parent, vreg->clk_ctrl_addr, + &vreg->clk_ctrl_reg); + if (rc) + goto bail; + + /* Save the current sleep control register state. */ + rc = pm8xxx_readb(vreg->dev->parent, vreg->sleep_ctrl_addr, + &vreg->sleep_ctrl_reg); + if (rc) + goto bail; + + /* + * get_voltage must return >0 in order for regulator_set_optimum_mode + * to succeed, but voltage may be unknown at probe time. + */ + vreg->save_uV = 1; /* This is not a no-op. */ + vreg->save_uV = _pm8921_smps_get_voltage(vreg); + + if ((vreg->clk_ctrl_reg & SMPS_CLK_CTRL_MASK) == SMPS_CLK_CTRL_PFM) + vreg->optimum = REGULATOR_MODE_STANDBY; + else + vreg->optimum = REGULATOR_MODE_FAST; + + /* Set advanced mode pull down enable based on platform data. */ + rc = pm8921_vreg_write(vreg, vreg->test_addr, + (vreg->pdata.pull_down_enable + ? SMPS_ADVANCED_PULL_DOWN_ENABLE : 0) + | REGULATOR_BANK_SEL(6) | REGULATOR_BANK_WRITE, + REGULATOR_BANK_MASK | SMPS_ADVANCED_PULL_DOWN_ENABLE, + &vreg->test_reg[6]); + if (rc) + goto bail; + + if (!SMPS_IN_ADVANCED_MODE(vreg)) { + /* Set legacy mode pull down enable based on platform data. */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + (vreg->pdata.pull_down_enable + ? SMPS_LEGACY_PULL_DOWN_ENABLE : 0), + SMPS_LEGACY_PULL_DOWN_ENABLE, &vreg->ctrl_reg); + if (rc) + goto bail; + } + +bail: + if (rc) + vreg_err(vreg, "pm8xxx_readb/writeb failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_init_ftsmps(struct pm8921_vreg *vreg) +{ + int rc, i; + u8 bank; + + /* Store current regulator register values. */ + rc = pm8xxx_readb(vreg->dev->parent, vreg->pfm_ctrl_addr, + &vreg->pfm_ctrl_reg); + if (rc) + goto bail; + + rc = pm8xxx_readb(vreg->dev->parent, vreg->pwr_cnfg_addr, + &vreg->pwr_cnfg_reg); + if (rc) + goto bail; + + /* Save the current fts_cnfg1 register state (uses 'test' member). */ + for (i = 0; i < SMPS_TEST_BANKS; i++) { + bank = REGULATOR_BANK_SEL(i); + rc = pm8xxx_writeb(vreg->dev->parent, vreg->test_addr, bank); + if (rc) + goto bail; + + rc = pm8xxx_readb(vreg->dev->parent, vreg->test_addr, + &vreg->test_reg[i]); + if (rc) + goto bail; + vreg->test_reg[i] |= REGULATOR_BANK_WRITE; + } + + /* + * get_voltage must return >0 in order for regulator_set_optimum_mode + * to succeed, but voltage may be unknown at probe time. + */ + vreg->save_uV = 1; /* This is not a no-op. */ + vreg->save_uV = _pm8921_ftsmps_get_voltage(vreg); + + if ((vreg->test_reg[0] & FTSMPS_CNFG1_PM_MASK) == FTSMPS_CNFG1_PM_PFM) + vreg->optimum = REGULATOR_MODE_STANDBY; + else + vreg->optimum = REGULATOR_MODE_FAST; + + /* Set pull down enable based on platform data. */ + rc = pm8921_vreg_write(vreg, vreg->pwr_cnfg_addr, + (vreg->pdata.pull_down_enable ? FTSMPS_PULL_DOWN_ENABLE : 0), + FTSMPS_PULL_DOWN_ENABLE_MASK, &vreg->pwr_cnfg_reg); + +bail: + if (rc) + vreg_err(vreg, "pm8xxx_readb/writeb failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_init_vs(struct pm8921_vreg *vreg) +{ + int rc = 0; + + vreg->optimum = REGULATOR_MODE_NORMAL; + + /* Set pull down enable based on platform data. */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + (vreg->pdata.pull_down_enable ? VS_PULL_DOWN_ENABLE : 0), + VS_PULL_DOWN_ENABLE_MASK, &vreg->ctrl_reg); + + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_init_vs300(struct pm8921_vreg *vreg) +{ + int rc; + + /* Set pull down enable based on platform data. */ + rc = pm8921_vreg_write(vreg, vreg->ctrl_addr, + (vreg->pdata.pull_down_enable ? VS300_PULL_DOWN_ENABLE : 0), + VS300_PULL_DOWN_ENABLE_MASK, &vreg->ctrl_reg); + + if (rc) + vreg_err(vreg, "pm8921_vreg_write failed, rc=%d\n", rc); + + return rc; +} + +static int pm8921_init_regulator(struct pm8921_vreg *vreg) +{ + int rc = 0; + + /* save the current control register state */ + rc = pm8xxx_readb(vreg->dev->parent, vreg->ctrl_addr, &vreg->ctrl_reg); + if (rc) { + vreg_err(vreg, "pm8xxx_readb failed, rc=%d\n", rc); + return rc; + } + + switch (vreg->type) { + case REGULATOR_TYPE_LDO: + rc = pm8921_init_ldo(vreg); + break; + case REGULATOR_TYPE_NLDO1200: + rc = pm8921_init_nldo1200(vreg); + break; + case REGULATOR_TYPE_SMPS: + rc = pm8921_init_smps(vreg); + break; + case REGULATOR_TYPE_FTSMPS: + rc = pm8921_init_ftsmps(vreg); + break; + case REGULATOR_TYPE_VS: + rc = pm8921_init_vs(vreg); + break; + case REGULATOR_TYPE_VS300: + rc = pm8921_init_vs300(vreg); + break; + } + + return rc; +} + +static int __devinit pm8921_vreg_probe(struct platform_device *pdev) +{ + struct regulator_desc *rdesc; + struct pm8921_vreg *vreg; + const char *reg_name = ""; + int rc = 0; + + if (pdev == NULL) + return -EINVAL; + + if (pdev->id >= 0 && pdev->id < PM8921_VREG_ID_MAX) { + rdesc = &pm8921_vreg_description[pdev->id]; + vreg = &pm8921_vreg[pdev->id]; + memcpy(&(vreg->pdata), pdev->dev.platform_data, + sizeof(struct pm8921_regulator_platform_data)); + reg_name = pm8921_vreg_description[pdev->id].name; + vreg->name = reg_name; + vreg->dev = &pdev->dev; + + rc = pm8921_init_regulator(vreg); + if (rc) + goto bail; + + vreg->rdev = regulator_register(rdesc, &pdev->dev, + &(vreg->pdata.init_data), vreg); + if (IS_ERR(vreg->rdev)) { + rc = PTR_ERR(vreg->rdev); + vreg->rdev = NULL; + pr_err("regulator_register failed for %s, rc=%d\n", + reg_name, rc); + } + } else { + rc = -ENODEV; + } + +bail: + if (rc) + pr_err("error for %s, rc=%d\n", reg_name, rc); + + return rc; +} + +static int __devexit pm8921_vreg_remove(struct platform_device *pdev) +{ + regulator_unregister(pm8921_vreg[pdev->id].rdev); + return 0; +} + +static struct platform_driver pm8921_vreg_driver = { + .probe = pm8921_vreg_probe, + .remove = __devexit_p(pm8921_vreg_remove), + .driver = { + .name = PM8921_REGULATOR_DEV_NAME, + .owner = THIS_MODULE, + }, +}; + +static int __init pm8921_vreg_init(void) +{ + return platform_driver_register(&pm8921_vreg_driver); +} +module_init(pm8921_vreg_init); + +static void __exit pm8921_vreg_exit(void) +{ + platform_driver_unregister(&pm8921_vreg_driver); +} +module_exit(pm8921_vreg_exit); + +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("PMIC8921 regulator driver"); +MODULE_VERSION("1.0"); +MODULE_ALIAS("platform:" PM8921_REGULATOR_DEV_NAME); diff --git a/include/linux/mfd/pm8xxx/pm8921.h b/include/linux/mfd/pm8xxx/pm8921.h index 19cffb2..c2794c3 100644 --- a/include/linux/mfd/pm8xxx/pm8921.h +++ b/include/linux/mfd/pm8xxx/pm8921.h @@ -22,6 +22,7 @@ #include #include #include +#include #define PM8921_NR_IRQS 256 @@ -44,6 +45,8 @@ struct pm8921_platform_data { struct pm8xxx_irq_platform_data *irq_pdata; struct pm8xxx_gpio_platform_data *gpio_pdata; struct pm8xxx_mpp_platform_data *mpp_pdata; + struct pm8921_regulator_platform_data *regulator_pdatas; + int num_regulators; }; #endif diff --git a/include/linux/regulator/pm8921-regulator.h b/include/linux/regulator/pm8921-regulator.h new file mode 100644 index 0000000..2622459 --- /dev/null +++ b/include/linux/regulator/pm8921-regulator.h @@ -0,0 +1,97 @@ +/* Copyright (c) 2011, Code Aurora Forum. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __PM8921_REGULATOR_H__ +#define __PM8921_REGULATOR_H__ + +#include + +#define PM8921_REGULATOR_DEV_NAME "pm8921-regulator" + +enum pm8921_vreg_id { + PM8921_VREG_ID_L1 = 0, + PM8921_VREG_ID_L2, + PM8921_VREG_ID_L3, + PM8921_VREG_ID_L4, + PM8921_VREG_ID_L5, + PM8921_VREG_ID_L6, + PM8921_VREG_ID_L7, + PM8921_VREG_ID_L8, + PM8921_VREG_ID_L9, + PM8921_VREG_ID_L10, + PM8921_VREG_ID_L11, + PM8921_VREG_ID_L12, + PM8921_VREG_ID_L14, + PM8921_VREG_ID_L15, + PM8921_VREG_ID_L16, + PM8921_VREG_ID_L17, + PM8921_VREG_ID_L18, + PM8921_VREG_ID_L21, + PM8921_VREG_ID_L22, + PM8921_VREG_ID_L23, + PM8921_VREG_ID_L24, + PM8921_VREG_ID_L25, + PM8921_VREG_ID_L26, + PM8921_VREG_ID_L27, + PM8921_VREG_ID_L28, + PM8921_VREG_ID_L29, + PM8921_VREG_ID_S1, + PM8921_VREG_ID_S2, + PM8921_VREG_ID_S3, + PM8921_VREG_ID_S4, + PM8921_VREG_ID_S5, + PM8921_VREG_ID_S6, + PM8921_VREG_ID_S7, + PM8921_VREG_ID_S8, + PM8921_VREG_ID_LVS1, + PM8921_VREG_ID_LVS2, + PM8921_VREG_ID_LVS3, + PM8921_VREG_ID_LVS4, + PM8921_VREG_ID_LVS5, + PM8921_VREG_ID_LVS6, + PM8921_VREG_ID_LVS7, + PM8921_VREG_ID_USB_OTG, + PM8921_VREG_ID_HDMI_MVS, + PM8921_VREG_ID_NCP, + PM8921_VREG_ID_MAX, +}; + +#define PM8921_VREG_PIN_CTRL_NONE 0x00 +#define PM8921_VREG_PIN_CTRL_A0 0x01 +#define PM8921_VREG_PIN_CTRL_A1 0x02 +#define PM8921_VREG_PIN_CTRL_D0 0x04 +#define PM8921_VREG_PIN_CTRL_D1 0x08 + +/* Minimum high power mode loads in uA. */ +#define PM8921_VREG_LDO_50_HPM_MIN_LOAD 5000 +#define PM8921_VREG_LDO_150_HPM_MIN_LOAD 10000 +#define PM8921_VREG_LDO_300_HPM_MIN_LOAD 10000 +#define PM8921_VREG_LDO_600_HPM_MIN_LOAD 10000 +#define PM8921_VREG_LDO_1200_HPM_MIN_LOAD 10000 +#define PM8921_VREG_SMPS_1500_HPM_MIN_LOAD 100000 +#define PM8921_VREG_SMPS_2000_HPM_MIN_LOAD 100000 + +/* Pin ctrl enables/disables or toggles high/low power modes */ +enum pm8921_vreg_pin_function { + PM8921_VREG_PIN_FN_ENABLE = 0, + PM8921_VREG_PIN_FN_MODE, +}; + +struct pm8921_regulator_platform_data { + struct regulator_init_data init_data; + int id; + unsigned pull_down_enable; + unsigned pin_ctrl; + enum pm8921_vreg_pin_function pin_fn; +}; + +#endif -- Sent by an employee of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum. -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/