Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1757657Ab1DCC7O (ORCPT ); Sat, 2 Apr 2011 22:59:14 -0400 Received: from mail-wy0-f174.google.com ([74.125.82.174]:43855 "EHLO mail-wy0-f174.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1757577Ab1DCC7M (ORCPT ); Sat, 2 Apr 2011 22:59:12 -0400 Date: Sun, 3 Apr 2011 03:59:07 +0100 From: Jamie Iles To: Thomas Gleixner Cc: Jamie Iles , LKML , Grant Likely , Russell King , Arnd Bergmann , Nicolas Pitre Subject: Re: [PATCH] gpio: support for Synopsys DesignWare APB GPIO Message-ID: <20110403025907.GA5670@pulham.picochip.com> References: <1301665638-29841-1-git-send-email-jamie@jamieiles.com> MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Disposition: inline In-Reply-To: User-Agent: Mutt/1.5.21 (2010-09-15) Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 16596 Lines: 505 Hi Thomas, It doesn't sound like it's worth resubmitting this driver and it would be better to focus on a generic GPIO driver - I can certainly see the attraction in that. I have a few comments inline particularly wrt IRQ handling stuff so I can hopefully get a better grasp on it. Many thanks for taking the time to review though, it's much appreciated. Jamie On Sun, Apr 03, 2011 at 12:10:04AM +0200, Thomas Gleixner wrote: > B1;2401;0cOn Fri, 1 Apr 2011, Jamie Iles wrote: > > > This patch adds support for the Synopsys DesignWare APB GPIO controller > > that can be found in some ARM systems. The controller supports up to > > Not only ARM. OK, fair enough. > > > 4x32 bit ports and port A is capable of raising interrupts. > > So I assume that there are already a bunch of ARM SoC gpio > implementations in the arch/arm/* space which implement the very same > thing. Did you check that? And if yes, then it would be very helpful > to actually convert those platforms so there is a reason why we merge > another instance. I did check the ones currently in arch/arm/ and I couldn't see any that were clearly Synposys DesignWare GPIO blocks. That's not to say there aren't any, but given the spec for the IP version I have I couldn't identify any. I work on a couple of ARM chips that use this block that we were hoping to mainline support for in the future. > > > +#define GPIO_SW_PORT_A_DR_REG_OFFSET 0x00 > > +#define GPIO_SW_PORT_A_DDR_REG_OFFSET 0x04 > > +#define GPIO_SW_PORT_A_CTL_REG_OFFSET 0x08 > > +#define GPIO_SW_PORT_B_DR_REG_OFFSET 0x0C > > I think this whole register offset thing needs to be runtime > configurable. We all know that SoC designers decide to move registers > around for pointless reasons or just change the stride. OK, for a generic GPIO driver I don't disagree but this comment isn't specific to this driver right? > > +#define GPIO_INT_EN_REG_OFFSET 0x30 > > +#define GPIO_INT_MASK_REG_OFFSET 0x34 > > I bet there are implementations of the very same thing which have irq > support for more than one port. So that wants to be generalized as > well. Perhaps if there are newer versions of the IP then Synopsys could have added support for interrupts on other ports but from the spec I have only port A can be configured for IRQs. > > > +/* > > + * Get the port mapping for the controller. There are 4 possible ports that > > + * we can use but some platforms may reserve ports for hardware purposes that > > + * cannot be used as GPIO so we allow these to be masked off. > > + */ > > +static void dw_gpio_configure_ports(struct dw_gpio_chip *dw, > > + unsigned long port_mask) > > +{ > > + unsigned long cfg1, cfg2; > > + int nr_ports; > > + > > + cfg1 = readl(dw->iobase + GPIO_CFG1_REG_OFFSET); > > + cfg2 = readl(dw->iobase + GPIO_CFG2_REG_OFFSET); > > + > > + nr_ports = (cfg1 & GPIO_NR_PORTS_MASK) >> GPIO_NR_PORTS_SHIFT; > > + > > + if (port_mask & DW_GPIO_PORTA_MASK) { > > + dw->porta_end = ((cfg2 & GPIO_PORTA_WIDTH_MASK) >> > > + GPIO_PORTA_WIDTH_SHIFT) + 1; > > + if (nr_ports == 1) > > + return; > > These nr_ports checks are pointless. This is a setup function and not > a hotpath. I put those there because it wasn't clear from the Synopsys documentation if the port widths for ports that weren't implemented were set to zero and don't have enough variety of implementations to test.. > > > + } else > > + dw->porta_end = 0; > > + > > + if (port_mask & DW_GPIO_PORTB_MASK) { > > + dw->portb_end = ((cfg2 & GPIO_PORTB_WIDTH_MASK) >> > > + GPIO_PORTB_WIDTH_SHIFT) + 1 + dw->porta_end; > > + if (nr_ports == 2) > > + return; > > + } else > > + dw->portb_end = dw->porta_end; > > + > > + if (port_mask & DW_GPIO_PORTC_MASK) { > > + dw->portc_end = ((cfg2 & GPIO_PORTC_WIDTH_MASK) >> > > + GPIO_PORTC_WIDTH_SHIFT) + 1 + dw->portb_end; > > + if (nr_ports == 3) > > + return; > > + } else > > + dw->portc_end = dw->portb_end; > > + > > + if (port_mask & DW_GPIO_PORTD_MASK) > > + dw->portd_end = ((cfg2 & GPIO_PORTD_WIDTH_MASK) >> > > + GPIO_PORTD_WIDTH_SHIFT) + 1 + dw->portc_end; > > + else > > + dw->portd_end = dw->portb_end; > > +} > > So you try to create a linear GPIO space which skips reserved > pins. What's the point of that? It adds useless overhead in the > hotpath for no value. It is confusing as there is no relation between > the HW pin and the gpio number anymore. > > Why can't we just have a linear space where the reserved gpios are > simply not accessible? So the reason here is that the IP may be configured with multiple ports of different sizes. A real world example we have is port widths of 8-16-1-32 and the only actual reserved GPIO is the single pin on port C. So we could say that the chip supports 128 GPIOs with loads of reserved GPIOs but that didn't seem too intuitive to me. I'm a bit conflicted on this one. > > > +#define __DWGPIO_REG(__chip, __gpio_nr, __reg) \ > > + ({ \ > > + void __iomem *ret = NULL; \ > > + if ((__gpio_nr) <= (__chip)->porta_end) \ > > + ret = ((__chip)->iobase + \ > > + GPIO_SW_PORT_A_##__reg##_REG_OFFSET); \ > > + else if ((__gpio_nr) <= (__chip)->portb_end) \ > > + ret = ((__chip)->iobase + \ > > + GPIO_SW_PORT_B_##__reg##_REG_OFFSET); \ > > + else if ((__gpio_nr) <= (__chip)->portc_end) \ > > + ret = ((__chip)->iobase + \ > > + GPIO_SW_PORT_C_##__reg##_REG_OFFSET); \ > > + else \ > > + ret = ((__chip)->iobase + \ > > + GPIO_SW_PORT_D_##__reg##_REG_OFFSET); \ > > + ret; \ > > + }) > > + > > > +static inline unsigned dw_gpio_bit_offs(struct dw_gpio_chip *dw, > > + unsigned offset) > > +{ > > + /* > > + * The gpios are controlled via three sets of registers. The register > > + * addressing is already taken care of by the __DWGPIO_REG macro, > > Shudder. A linear mapping would avoid all that ugliness. Yes, that would certainly simplify all of this. > > > + * this takes care of the bit offsets within each register. > > + */ > > + if (offset <= dw->porta_end) > > + return offset; > > + else if (offset <= dw->portb_end) > > + return offset - dw->porta_end; > > + else if (offset <= dw->portc_end) > > + return offset - dw->portb_end; > > + else > > + return offset - dw->portc_end; > > +} > > + > > +static int dwgpio_direction_input(struct gpio_chip *chip, unsigned offset) > > +{ > > + struct dw_gpio_chip *dw = to_dw_gpio_chip(chip); > > + void __iomem *ddr = DWGPIO_DDR(dw, offset); > > + void __iomem *cr = DWGPIO_CTL(dw, offset); > > + unsigned long flags, val, bit_offset = dw_gpio_bit_offs(dw, offset); > > + > > + spin_lock_irqsave(&dw->lock, flags); > > + /* Mark the pin as an output. */ > > + val = readl(ddr); > > Why is this value not cached ? Fair point! > > > + val &= ~(1 << bit_offset); > > + writel(val, ddr); > > + > > + /* Set the pin as software controlled. */ > > + val = readl(cr); > > Ditto > > > + val &= ~(1 << bit_offset); > > + writel(val, cr); > > + spin_unlock_irqrestore(&dw->lock, flags); > > + > > + return 0; > > +} > > + > > +static int dwgpio_get(struct gpio_chip *chip, unsigned offset) > > +{ > > + struct dw_gpio_chip *dw = to_dw_gpio_chip(chip); > > + void __iomem *ext = DWGPIO_EXT(dw, offset); > > + unsigned long bit_offset = dw_gpio_bit_offs(dw, offset); > > + > > + return !!(readl(ext) & (1 << bit_offset)); > > +} > > + > > +static void dwgpio_set(struct gpio_chip *chip, unsigned offset, int value) > > +{ > > + struct dw_gpio_chip *dw = to_dw_gpio_chip(chip); > > + void __iomem *dr = DWGPIO_DR(dw, offset); > > + unsigned long val, flags, bit_offset = dw_gpio_bit_offs(dw, offset); > > + > > + spin_lock_irqsave(&dw->lock, flags); > > + val = readl(dr); > > Even more so. More instances ignored. > > > +static void dwgpio_irq_enable(struct irq_data *d) > > +{ > > + int gpio = irq_to_gpio(d->irq); > > + struct dw_gpio_chip *dw = irq_data_get_irq_chip_data(d); > > + void *port_inten = INT_EN_REG(dw); > > + unsigned long val, flags; > > + > > + spin_lock_irqsave(&dw->lock, flags); > > This is nested into irq_desc->lock and wants to be a raw_spinlock > therefor. OK, thanks. > > > + val = readl(port_inten); > > + val |= (1 << gpio); > > + writel(val, port_inten); > > + spin_unlock_irqrestore(&dw->lock, flags); > > +} > > + > > +static void dwgpio_irq_disable(struct irq_data *d) > > +{ > > + int gpio = irq_to_gpio(d->irq); > > + struct dw_gpio_chip *dw = irq_data_get_irq_chip_data(d); > > + void __iomem *port_inten = INT_EN_REG(dw); > > All this information can be precomputed at setup time and supplied as > irq_chip_data to the irq in a form wich does not require to compute it > over and over. OK, that makes sense. > > > +static void dwgpio_irq_ack(struct irq_data *d) > > +{ > > + int gpio = irq_to_gpio(d->irq); > > + struct dw_gpio_chip *dw = irq_data_get_irq_chip_data(d); > > + void __iomem *port_intmask = INT_MASK_REG(dw); > > + void __iomem *port_eoi = EOI_REG(dw); > > + void __iomem *port_inttype_level = INT_TYPE_REG(dw); > > + unsigned long val, flags; > > + > > + spin_lock_irqsave(&dw->lock, flags); > > + val = readl(port_inttype_level); > > + if (val & (1 << gpio)) { > > + /* Edge-sensitive */ > > + val = readl(port_eoi); > > + val |= (1 << gpio); > > + writel(val, port_eoi); > > + } else { > > + /* Level-sensitive */ > > + val = readl(port_intmask); > > + val |= (1 << gpio); > > + writel(val, port_intmask); > > + } > > These conditionals are completely wrong. We use different irq_chip > implementations to distinguish different flows. I'm not sure I understand this, are you saying that there would be two 'struct irq_chip's - one for level and the other for edge or are you referring to the flows internal to the generic IRQ layer? If the former, then is it safe to assign another chip to an IRQ in the .irq_set_type method of another chip or am I barking up the wrong tree here? I can see that I shouldn't be doing the mask for the level-sensitive IRQ here though. > > > + spin_unlock_irqrestore(&dw->lock, flags); > > +} > > > +static int dwgpio_irq_set_type(struct irq_data *d, > > + unsigned int trigger) > > +{ > > + int gpio = irq_to_gpio(d->irq); > > + struct dw_gpio_chip *dw = irq_data_get_irq_chip_data(d); > > + void __iomem *port_inttype_level = INT_TYPE_REG(dw); > > + void __iomem *port_int_polarity = INT_POLARITY_REG(dw); > > + unsigned long level, polarity, flags; > > + > > + if (trigger & ~(IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING | > > + IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) > > + return -EINVAL; > > + > > + spin_lock_irqsave(&dw->lock, flags); > > + level = readl(port_inttype_level); > > + polarity = readl(port_int_polarity); > > + > > + if (trigger & IRQ_TYPE_EDGE_RISING) { > > + level |= (1 << gpio); > > + polarity |= (1 << gpio); > > + } else if (trigger & IRQ_TYPE_EDGE_FALLING) { > > + level |= (1 << gpio); > > + polarity &= ~(1 << gpio); > > + } else if (trigger & IRQ_TYPE_LEVEL_HIGH) { > > + level &= ~(1 << gpio); > > + polarity |= (1 << gpio); > > + } else if (trigger & IRQ_TYPE_LEVEL_LOW) { > > + level &= ~(1 << gpio); > > + polarity &= ~(1 << gpio); > > + } > > + > > + writel(level, port_inttype_level); > > + writel(polarity, port_int_polarity); > > So this should set the proper irq chip for the edge/level flow, but > yes that's pointless. See below. OK, got that. > > > + spin_unlock_irqrestore(&dw->lock, flags); > > + > > + return 0; > > +} > > + > > +static struct irq_chip dwgpio_irqchip = { > > + .name = "dwgpio", > > + .irq_ack = dwgpio_irq_ack, > > + .irq_mask = dwgpio_irq_mask, > > + .irq_unmask = dwgpio_irq_unmask, > > + .irq_enable = dwgpio_irq_enable, > > + .irq_disable = dwgpio_irq_disable, > > + .irq_set_type = dwgpio_irq_set_type, > > +}; > > + > > +static void dw_gpio_irq_handler(unsigned irq, struct irq_desc *desc) > > +{ > > + struct dw_gpio_chip *dw = irq_get_handler_data(irq); > > + int i; > > + > > + /* > > + * Mask and ack the interrupt in the parent interrupt controller > > + * before handling it. > > + */ > > + desc->irq_data.chip->irq_mask(&desc->irq_data); > > + desc->irq_data.chip->irq_ack(&desc->irq_data); > > Please get chip and irq_data with the proper accessors. > > > + for (;;) { > > + unsigned long status = readl(INT_STATUS_REG(dw)); > > + > > + if (!status) > > + break; > > + writel(status, EOI_REG(dw)); > > + > > + for_each_set_bit(i, &status, 8) > > + generic_handle_irq(dw->irq_base + i); > > + } > > + desc->irq_data.chip->irq_unmask(&desc->irq_data); > > +} > > + > > +/* > > + * We want to enable/disable interrupts for the GPIO pins through the GPIO > > + * block itself. The current configuration assumes a 1-to-1 mapping of GPIO > > + * interrupt sources to IRQ numbers. We use a chained handler as the GPIO > > + * IRQ's may pass through a separate VIC on some systems so need to be > > + * enabled/disabled there too. > > + * > > + * The chained handler simply converts from the virtual IRQ handler to the > > + * real interrupt source and calls the GPIO IRQ handler. > > + */ > > +static void dwgpio_irq_init(struct dw_gpio_chip *dw, > > + struct resource *demux_irqs, > > + struct resource *irqs) > > +{ > > + int i; > > + > > + if (!demux_irqs && !irqs) > > + return; > > + > > + if (!demux_irqs || !irqs || > > + resource_size(demux_irqs) != resource_size(irqs)) { > > + dev_warn(dw->chip.dev, "unsupported IRQ demuxing configuration, continuing without GPIO IRQ support\n"); > > + return; > > + } > > + > > + dw->irq_base = irqs->start; > > + > > + writel(0, INT_EN_REG(dw)); > > + writel(~0, EOI_REG(dw)); > > + for (i = irqs->start; i <= irqs->end; ++i) { > > + irq_set_chip_and_handler_name(i, &dwgpio_irqchip, > > + handle_simple_irq, "demux"); > > Why do you have irq_ack/mask/unmask functions when you use > handle_simple_irq? Just because the random driver you copied from has > them as well? They are never called. So would it be correct to start of with handle_level_irq() then to change the handler in the irq_set_type method with __irq_set_handler_locked(). > > > + irq_set_chip_data(i, dw); > > + irq_set_status_flags(i, IRQ_TYPE_EDGE_BOTH | > > + IRQ_TYPE_LEVEL_HIGH | > > + IRQ_TYPE_LEVEL_LOW); > > What's that for ? I thought that meant that the IRQ was capable of being driven by these methods but I guess that's not the case. Should this be saying what the interrupt type currently is? I guess this can probably be removed completely here. > > > + set_irq_flags(i, IRQF_VALID | IRQF_PROBE); > > Why are those irqs probable ? I'm sorry to say that these came from existing drivers and these shouldn't be probeable. > > + } > > + > > + for (i = demux_irqs->start; i <= demux_irqs->end; ++i) { > > + irq_set_handler_data(i, dw); > > + irq_set_chained_handler(i, dw_gpio_irq_handler); > > + set_irq_flags(i, IRQF_VALID); > > + } > > +} > > > +static void dwgpio_irq_stop(struct dw_gpio_chip *dw, > > + struct resource *demux_irqs, > > + struct resource *irqs) > > +{ > > + int i; > > + > > + if (!demux_irqs || !irqs || > > + resource_size(demux_irqs) != resource_size(irqs)) > > + return; > > + > > + for (i = irqs->start; i < irqs->end; ++i) { > > Are those interrupts disabled? And what removes the handler ? So what would be the preferred way of handling this? I can see that checking that all of the IRQs are disabled first then return -EBUSY from the .remove() method of the driver if not would be one way, but perhaps there's a better alternative. > > + irq_set_chip(i, NULL); > > + irq_set_chip_data(i, NULL); > > + } > > + > > + for (i = demux_irqs->start; i < demux_irqs->end; ++i) { > > Ditto > > > + irq_set_chip(i, NULL); > > + irq_set_chip_data(i, NULL); > > + } > > +} > > Sigh. This is another incarnation of a bog standard GPIO driver, which > has the ever repeating pattern of configuration, input read, output > write and interrupt functions. It's about time to stop that nonsense. > > GPIO implementations are not that different and we really want to > abstract out the few implementations and be done with it. Fair comments. I don't feel I have the expertise to undertake this generic abstraction myself but I'd be more than happy to help out if someone else did. Thanks again for the review, Jamie -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/