MIME-Version: 1.0
In-Reply-To: <BANLkTimhk-szP=gbZLpRrofi2EB2YbXrqg@mail.gmail.com>
References: <90e49570-bc82-41a9-ac79-2f5007e93a2a@VA3EHSMHS018.ehs.local> <BANLkTimhk-szP=gbZLpRrofi2EB2YbXrqg@mail.gmail.com>
From: Grant Likely <grant.likely@secretlab.ca>
Date: Fri, 22 Apr 2011 09:46:09 -0600
Message-ID: <BANLkTim2TyamL4Q+=b-So6phTF+Ng-cBUA@mail.gmail.com>
Subject: Re: [PATCH V2] tty/serial: add support for Xilinx PS UART
To: John Linn <john.linn@xilinx.com>
Cc: linux-kernel@vger.kernel.org, linux-serial@vger.kernel.org,
        alan@lxorguk.ukuu.org.uk, greg@kroah.com
Content-Type: text/plain; charset=ISO-8859-1
Content-Transfer-Encoding: 8BIT
Sender: linux-kernel-owner@vger.kernel.org
Content-Length: 3716
Lines: 78

On Fri, Apr 22, 2011 at 9:40 AM, Grant Likely <grant.likely@secretlab.ca> wrote:
> On Wed, Apr 20, 2011 at 1:03 PM, John Linn <john.linn@xilinx.com> wrote:
>> The Xilinx PS Uart is used on the new ARM based SoC. This
>> UART is not compatible with others such that a seperate
>> driver is required.
>>
>> Signed-off-by: John Linn <john.linn@xilinx.com>
>
> Out of curiosity, who is the vendor of this uart IP block? ?Is it new
> hardware created by xilinx for zinq, or is it provided by a third
> party. ?If its from a third party it is within the realm of
> possibility that a driver already exists for it.
>
> g.
>> +/********************************Register Map********************************/
>> +/** UART
>> + *
>> + * Register offsets for the UART.
>> + *
>> + */
>> +#define XUARTPS_CR_OFFSET ? ? ?0x00 ?/* Control Register [8:0] */
>> +#define XUARTPS_MR_OFFSET ? ? ?0x04 ?/* Mode Register [10:0] */
>> +#define XUARTPS_IER_OFFSET ? ? 0x08 ?/* Interrupt Enable [10:0] */
>> +#define XUARTPS_IDR_OFFSET ? ? 0x0C ?/* Interrupt Disable [10:0] */
>> +#define XUARTPS_IMR_OFFSET ? ? 0x10 ?/* Interrupt Mask [10:0] */
>> +#define XUARTPS_ISR_OFFSET ? ? 0x14 ?/* Interrupt Status [10:0]*/
>> +#define XUARTPS_BAUDGEN_OFFSET 0x18 ?/* Baud Rate Generator [15:0] */
>> +#define XUARTPS_RXTOUT_OFFSET ?0x1C ?/* RX Timeout [7:0] */
>> +#define XUARTPS_RXWM_OFFSET ? ?0x20 ?/* RX FIFO Trigger Level [5:0] */
>> +#define XUARTPS_MODEMCR_OFFSET 0x24 ?/* Modem Control [5:0] */
>> +#define XUARTPS_MODEMSR_OFFSET 0x28 ?/* Modem Status [8:0] */
>> +#define XUARTPS_SR_OFFSET ? ? ?0x2C ?/* Channel Status [11:0] */
>> +#define XUARTPS_FIFO_OFFSET ? ?0x30 ?/* FIFO [15:0] or [7:0] */
>> +#define XUARTPS_BAUDDIV_OFFSET 0x34 ?/* Baud Rate Divider [7:0] */
>> +#define XUARTPS_FLOWDEL_OFFSET 0x38 ?/* Flow Delay [15:0] */
>> +#define XUARTPS_IRRX_PWIDTH_OFFSET 0x3C /* IR Minimum Received Pulse
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? Width [15:0] */
>> +#define XUARTPS_IRTX_PWIDTH_OFFSET 0x40 /* IR Transmitted pulse
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? Width [7:0] */
>> +#define XUARTPS_TXWM_OFFSET ? ?0x44 ?/* TX FIFO Trigger Level [5:0] */

After a quick search:

from include/linux/atmel_serial.h
#define ATMEL_US_CR             0x00                    /* Control Register */
#define ATMEL_US_MR             0x04                    /* Mode Register */
#define ATMEL_US_IER            0x08                    /* Interrupt
Enable Register */
#define ATMEL_US_IDR            0x0c                    /* Interrupt
Disable Register */
#define ATMEL_US_IMR            0x10                    /* Interrupt
Mask Register */
#define ATMEL_US_CSR            0x14                    /* Channel
Status Register */
#define ATMEL_US_RHR            0x18                    /* Receiver
Holding Register */
#define ATMEL_US_THR            0x1c                    /* Transmitter
Holding Register */
#define ATMEL_US_BRGR           0x20                    /* Baud Rate
Generator Register */
#define ATMEL_US_RTOR           0x24                    /* Receiver
Time-out Register */
#define ATMEL_US_TTGR           0x28                    /* Transmitter
Timeguard Register */
#define ATMEL_US_FIDI           0x40                    /* FI DI Ratio
Register */
#define ATMEL_US_NER            0x44                    /* Number of
Errors Register */
#define ATMEL_US_IF             0x4c                    /* IrDA Filter
Register */


Not exactly the same, but worth exploring
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/