Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1758292Ab1F1Ot2 (ORCPT ); Tue, 28 Jun 2011 10:49:28 -0400 Received: from imr4.ericy.com ([198.24.6.8]:53783 "EHLO imr4.ericy.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1758308Ab1F1On4 (ORCPT ); Tue, 28 Jun 2011 10:43:56 -0400 Date: Tue, 28 Jun 2011 07:43:03 -0700 From: Guenter Roeck To: Alexander Stein CC: Jean Delvare , "lm-sensors@lm-sensors.org" , "linux-kernel@vger.kernel.org" Subject: Re: [PATCH v3] hwmon: LM95245 driver Message-ID: <20110628144303.GA29554@ericsson.com> References: <20110627202135.GA12829@ericsson.com> <1309244829-12304-1-git-send-email-alexander.stein@systec-electronic.com> MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Disposition: inline In-Reply-To: <1309244829-12304-1-git-send-email-alexander.stein@systec-electronic.com> User-Agent: Mutt/1.5.20 (2009-06-14) Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 23093 Lines: 664 On Tue, Jun 28, 2011 at 03:07:09AM -0400, Alexander Stein wrote: > An hwmon driver for the National Semiconductor LM95245 dual temperature > sensors chip. > > Signed-off-by: Alexander Stein > --- > Changes since v2: > * Applied review notes from Guenter > * Added Documentation/hwmon/lm95245 (Dunno if is enough though) > > Guenter, > I skipped adding OS limits. For one point I don't understand them exactly. > TCRIT and OS limit is indicated the same for local temperature and AFAICS > it uses the external pin A0/OS which have to be configured. I can't test this. > Hi Alexander, no problem. I requested samples, so I may add that myself later on if I can get it to work and if I think it makes sense. Only nitpicks this time around. > Documentation/hwmon/lm95245 | 33 +++ > drivers/hwmon/Kconfig | 9 + > drivers/hwmon/Makefile | 1 + > drivers/hwmon/lm95245.c | 517 +++++++++++++++++++++++++++++++++++++++++++ > 4 files changed, 560 insertions(+), 0 deletions(-) > create mode 100644 Documentation/hwmon/lm95245 > create mode 100644 drivers/hwmon/lm95245.c > > diff --git a/Documentation/hwmon/lm95245 b/Documentation/hwmon/lm95245 > new file mode 100644 > index 0000000..7472c64 > --- /dev/null > +++ b/Documentation/hwmon/lm95245 > @@ -0,0 +1,33 @@ > +Kernel driver lm95245 > +================== > + > +Supported chips: > + * National Semiconductor LM95245 > + Addresses scanned: I2C 0x18, 0x19, 0x29, 0x4c, 0x4d > + Datasheet: Publicly available at the National Semiconductor website > + http://www.national.com/mpf/LM/LM95245.html > + > + > +Author: Alexander Stein > + > +Description > +----------- > + > +The LM95245 is an 11-bit digital temperature sensor with a 2-wire System > +Management Bus (SMBus) interface and TruTherm technology that can monitor > +the temperature of a remote diode as well as its own temperature. > +The LM95245 can be used to very accurately monitor the temperature of > +external devices such as microprocessors. > + > +All temperature values are given in millidegrees Celsius. Local temperature > +is given within a range of -127 to +127.875 degrees. Remote temperatures are > +given within a range of -127 to +255 degrees. Resolution depends on > +temperature input and range. > + > +Each sensor has its own critical limit, but the hysteresis is common to all > +two channels. > + > +The lm95245 driver can change its update interval to a fixed set of values. > +It will round up to the next selectable interval. See the datasheet for exact > +values. Reading them more often will do no harm, but will return s/them/sensor values/ > +'old' values. > diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig > index 16db83c..ffabf1f 100644 > --- a/drivers/hwmon/Kconfig > +++ b/drivers/hwmon/Kconfig > @@ -702,6 +702,15 @@ config SENSORS_LM95241 > This driver can also be built as a module. If so, the module > will be called lm95241. > > +config SENSORS_LM95245 > + tristate "National Semiconductor LM95245 sensor chip" > + depends on I2C && EXPERIMENTAL > + help > + If you say yes here you get support for LM95245 sensor chip. > + > + This driver can also be built as a module. If so, the module > + will be called lm95245. > + > config SENSORS_MAX1111 > tristate "Maxim MAX1111 Multichannel, Serial 8-bit ADC chip" > depends on SPI_MASTER > diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile > index 28061cf..5598712 100644 > --- a/drivers/hwmon/Makefile > +++ b/drivers/hwmon/Makefile > @@ -80,6 +80,7 @@ obj-$(CONFIG_SENSORS_LM90) += lm90.o > obj-$(CONFIG_SENSORS_LM92) += lm92.o > obj-$(CONFIG_SENSORS_LM93) += lm93.o > obj-$(CONFIG_SENSORS_LM95241) += lm95241.o > +obj-$(CONFIG_SENSORS_LM95245) += lm95245.o > obj-$(CONFIG_SENSORS_LTC4151) += ltc4151.o > obj-$(CONFIG_SENSORS_LTC4215) += ltc4215.o > obj-$(CONFIG_SENSORS_LTC4245) += ltc4245.o > diff --git a/drivers/hwmon/lm95245.c b/drivers/hwmon/lm95245.c > new file mode 100644 > index 0000000..014973d > --- /dev/null > +++ b/drivers/hwmon/lm95245.c > @@ -0,0 +1,517 @@ > +/* > + * Copyright (C) 2011 Alexander Stein > + * > + * The LM95245 is a sensor chip made by National Semiconductors. > + * It reports up to two temperatures (its own plus an external one). > + * Complete datasheet can be obtained from National's website at: > + * http://www.national.com/ds.cgi/LM/LM95245.pdf > + * > + * This driver is based on lm95241.c > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * You should have received a copy of the GNU General Public License > + * along with this program; if not, write to the Free Software > + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. > + */ > + > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > + > +#define DEVNAME "lm95245" > + > +static const unsigned short normal_i2c[] = { > + 0x18, 0x19, 0x29, 0x4c, 0x4d, I2C_CLIENT_END }; > + > +/* LM95245 registers */ > +/* general registers */ > +#define LM95245_REG_RW_CONFIG1 0x03 > +#define LM95245_REG_RW_CONVERS_RATE 0x04 > +#define LM95245_REG_W_ONE_SHOT 0x0F > + > +/* diode configuration */ > +#define LM95245_REG_RW_CONFIG2 0xBF > +#define LM95245_REG_RW_REMOTE_OFFH 0x11 > +#define LM95245_REG_RW_REMOTE_OFFL 0x12 > + > +/* status registers */ > +#define LM95245_REG_R_STATUS1 0x02 > +#define LM95245_REG_R_STATUS2 0x33 > + > +/* limit registers */ > +#define LM95245_REG_RW_REMOTE_OS_LIMIT 0x07 > +#define LM95245_REG_RW_LOCAL_OS_TCRIT_LIMIT 0x20 > +#define LM95245_REG_RW_REMOTE_TCRIT_LIMIT 0x19 > +#define LM95245_REG_RW_COMMON_HYSTERESIS 0x21 > + > +/* temperature signed */ > +#define LM95245_REG_R_LOCAL_TEMPH_S 0x00 > +#define LM95245_REG_R_LOCAL_TEMPL_S 0x30 > +#define LM95245_REG_R_REMOTE_TEMPH_S 0x01 > +#define LM95245_REG_R_REMOTE_TEMPL_S 0x10 > +/* temperature unsigned */ > +#define LM95245_REG_R_REMOTE_TEMPH_U 0x31 > +#define LM95245_REG_R_REMOTE_TEMPL_U 0x32 > + > +/* id registers */ > +#define LM95245_REG_R_MAN_ID 0xFE > +#define LM95245_REG_R_CHIP_ID 0xFF > + > +/* LM95245 specific bitfields */ > +#define CFG_STOP 0x40 > +#define CFG_REMOTE_TCRIT_MASK 0x10 > +#define CFG_REMOTE_OS_MASK 0x08 > +#define CFG_LOCAL_TCRIT_MASK 0x04 > +#define CFG_LOCAL_OS_MASK 0x02 > + > +#define CFG2_OS_A0 0x40 > +#define CFG2_DIODE_FAULT_OS 0x20 > +#define CFG2_DIODE_FAULT_TCRIT 0x10 > +#define CFG2_REMOTE_TT 0x08 > +#define CFG2_REMOTE_FILTER_DIS 0x00 > +#define CFG2_REMOTE_FILTER_EN 0x06 > + > +/* conversation rate in ms */ > +#define RATE_CR0063 0x00 > +#define RATE_CR0364 0x01 > +#define RATE_CR1000 0x02 > +#define RATE_CR2500 0x03 > + > +#define STATUS1_DIODE_FAULT 0x04 > +#define STATUS1_RTCRIT 0x02 > +#define STATUS1_LOC 0x01 > + > +#define MANUFACTURER_ID 0x01 > +#define DEFAULT_REVISION 0xB3 > + > +static const u8 lm95245_reg_address[] = { > + LM95245_REG_R_LOCAL_TEMPH_S, > + LM95245_REG_R_LOCAL_TEMPL_S, > + LM95245_REG_R_REMOTE_TEMPH_S, > + LM95245_REG_R_REMOTE_TEMPL_S, > + LM95245_REG_R_REMOTE_TEMPH_U, > + LM95245_REG_R_REMOTE_TEMPL_U, > + LM95245_REG_RW_LOCAL_OS_TCRIT_LIMIT, > + LM95245_REG_RW_REMOTE_TCRIT_LIMIT, > + LM95245_REG_RW_COMMON_HYSTERESIS, > + LM95245_REG_R_STATUS1, > +}; > + > +/* Client data (each client gets its own) */ > +struct lm95245_data { > + struct device *hwmon_dev; > + struct mutex update_lock; > + unsigned long last_updated; /* in jiffies */ > + unsigned long interval; /* in msecs */ > + char valid; /* zero until following fields are valid */ Just a side note ... char doesn't buy you anything here, and will only make the code more complex, at least for some architectures. You'd be better off using int (or bool if you want to be fancy). > + /* registers values */ > + u8 regs[ARRAY_SIZE(lm95245_reg_address)]; > + u8 config1, config2; > +}; > + > +/* Conversions */ > +static int TempFromRegUnsigned(u8 val_h, u8 val_l) > +{ > + return val_h * 1000 + val_l * 1000 / 256; > +} > + > +static int TempFromRegSigned(u8 val_h, u8 val_l) > +{ > + if (val_h & 0x80) > + return (val_h - 0x100) * 1000; > + return TempFromRegUnsigned(val_h, val_l); > +} > + I keep forgetting this ... the above function names violate CodingStyle, chapter 4 ("mixed-case names are frowned upon"). > +static struct lm95245_data *lm95245_update_device(struct device *dev) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct lm95245_data *data = i2c_get_clientdata(client); > + > + mutex_lock(&data->update_lock); > + > + if (time_after(jiffies, data->last_updated > + + msecs_to_jiffies(data->interval)) || !data->valid) { > + int i; > + > + dev_dbg(&client->dev, "Updating lm95245 data.\n"); > + for (i = 0; i < ARRAY_SIZE(lm95245_reg_address); i++) > + data->regs[i] > + = i2c_smbus_read_byte_data(client, > + lm95245_reg_address[i]); > + data->last_updated = jiffies; > + data->valid = 1; > + } > + > + mutex_unlock(&data->update_lock); > + > + return data; > +} > + > +static unsigned long lm95245_set_conversion_rate(struct i2c_client *client, > + unsigned long interval) > +{ > + int rate; > + > + if (interval <= 63) { > + interval = 63; > + rate = RATE_CR0063; > + } else if (interval <= 364) { > + interval = 364; > + rate = RATE_CR0364; > + } else if (interval <= 1000) { > + interval = 1000; > + rate = RATE_CR1000; > + } else { > + interval = 2500; > + rate = RATE_CR2500; > + } > + > + i2c_smbus_write_byte_data(client, LM95245_REG_RW_CONVERS_RATE, rate); > + > + return interval; > +} > + > +/* Sysfs stuff */ > +static ssize_t show_input(struct device *dev, struct device_attribute *attr, > + char *buf) > +{ > + struct lm95245_data *data = lm95245_update_device(dev); > + int temp; > + int index = to_sensor_dev_attr(attr)->index; > + > + /* > + * Index 0 (Local temp) is always signed > + * Index 2 (Remote temp) has both signed and unsigned data > + * use signed calculation for remote if signed bit is set > + */ > + if (index == 0 || data->regs[index] & 0x80) > + temp = TempFromRegSigned(data->regs[index], > + data->regs[index + 1]); > + else > + temp = TempFromRegUnsigned(data->regs[index + 2], > + data->regs[index + 3]); > + > + return snprintf(buf, PAGE_SIZE - 1, "%d\n", temp); > +} > + > +static ssize_t show_limit(struct device *dev, struct device_attribute *attr, > + char *buf) > +{ > + struct lm95245_data *data = lm95245_update_device(dev); > + int index = to_sensor_dev_attr(attr)->index; > + > + return snprintf(buf, PAGE_SIZE - 1, "%d\n", > + data->regs[index] * 1000); > +} > + > +static ssize_t set_limit(struct device *dev, struct device_attribute *attr, > + const char *buf, size_t count) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct lm95245_data *data = i2c_get_clientdata(client); > + int index = to_sensor_dev_attr(attr)->index; > + unsigned long val; > + > + if (strict_strtoul(buf, 10, &val) < 0) > + return -EINVAL; > + > + val /= 1000; > + > + val = SENSORS_LIMIT(val, 0, (index == 6 ? 127 : 255)); > + > + mutex_lock(&data->update_lock); > + > + data->valid = 0; > + > + i2c_smbus_write_byte_data(client, lm95245_reg_address[index], val); > + > + mutex_unlock(&data->update_lock); > + > + return count; > +} > + > +static ssize_t set_crit_hyst(struct device *dev, struct device_attribute *attr, > + const char *buf, size_t count) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct lm95245_data *data = i2c_get_clientdata(client); > + unsigned long val; > + > + if (strict_strtoul(buf, 10, &val) < 0) > + return -EINVAL; > + > + val /= 1000; > + > + val = SENSORS_LIMIT(val, 0, 31); > + > + mutex_lock(&data->update_lock); > + > + data->valid = 0; > + > + /* shared crit hysteresis */ > + i2c_smbus_write_byte_data(client, LM95245_REG_RW_COMMON_HYSTERESIS, > + val); > + > + mutex_unlock(&data->update_lock); > + > + return count; > +} > + > +static ssize_t show_type(struct device *dev, struct device_attribute *attr, > + char *buf) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct lm95245_data *data = i2c_get_clientdata(client); > + > + return snprintf(buf, PAGE_SIZE - 1, > + data->config2 & CFG2_REMOTE_TT ? "1\n" : "2\n"); > +} > + > +static ssize_t set_type(struct device *dev, struct device_attribute *attr, > + const char *buf, size_t count) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct lm95245_data *data = i2c_get_clientdata(client); > + unsigned long val; > + > + if (strict_strtoul(buf, 10, &val) < 0) > + return -EINVAL; > + if (val != 1 && val != 2) > + return -EINVAL; > + > + mutex_lock(&data->update_lock); > + > + if (val == 1) > + data->config2 |= CFG2_REMOTE_TT; > + else > + data->config2 &= ~CFG2_REMOTE_TT; > + > + data->valid = 0; > + > + i2c_smbus_write_byte_data(client, LM95245_REG_RW_CONFIG2, > + data->config2); > + > + mutex_unlock(&data->update_lock); > + > + return count; > +} > + > +static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, > + char *buf) > +{ > + struct lm95245_data *data = lm95245_update_device(dev); > + int index = to_sensor_dev_attr(attr)->index; > + > + return snprintf(buf, PAGE_SIZE - 1, "%d\n", > + !!(data->regs[9] & index)); > +} > + > +static ssize_t show_interval(struct device *dev, struct device_attribute *attr, > + char *buf) > +{ > + struct lm95245_data *data = lm95245_update_device(dev); > + > + return snprintf(buf, PAGE_SIZE - 1, "%lu\n", data->interval); > +} > + > +static ssize_t set_interval(struct device *dev, struct device_attribute *attr, > + const char *buf, size_t count) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct lm95245_data *data = i2c_get_clientdata(client); > + unsigned long val; > + > + if (strict_strtoul(buf, 10, &val) < 0) > + return -EINVAL; > + > + mutex_lock(&data->update_lock); > + > + data->interval = lm95245_set_conversion_rate(client, val); > + > + mutex_unlock(&data->update_lock); > + > + return count; > +} > + > +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_input, NULL, 0); > +static SENSOR_DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO, show_limit, > + set_limit, 6); > +static SENSOR_DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO, show_limit, > + set_crit_hyst, 8); > +static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, > + STATUS1_LOC); > + > +static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_input, NULL, 2); > +static SENSOR_DEVICE_ATTR(temp2_crit, S_IWUSR | S_IRUGO, show_limit, > + set_limit, 7); > +static SENSOR_DEVICE_ATTR(temp2_crit_hyst, S_IWUSR | S_IRUGO, show_limit, > + set_crit_hyst, 8); > +static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, > + STATUS1_RTCRIT); > +static SENSOR_DEVICE_ATTR(temp2_type, S_IWUSR | S_IRUGO, show_type, > + set_type, 0); > +static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, > + STATUS1_DIODE_FAULT); > + > +static DEVICE_ATTR(update_interval, S_IWUSR | S_IRUGO, show_interval, > + set_interval); > + > +static struct attribute *lm95245_attributes[] = { > + &sensor_dev_attr_temp1_input.dev_attr.attr, > + &sensor_dev_attr_temp1_crit.dev_attr.attr, > + &sensor_dev_attr_temp1_crit_hyst.dev_attr.attr, > + &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr, > + &sensor_dev_attr_temp2_input.dev_attr.attr, > + &sensor_dev_attr_temp2_crit.dev_attr.attr, > + &sensor_dev_attr_temp2_crit_hyst.dev_attr.attr, > + &sensor_dev_attr_temp2_crit_alarm.dev_attr.attr, > + &sensor_dev_attr_temp2_type.dev_attr.attr, > + &sensor_dev_attr_temp2_fault.dev_attr.attr, > + &dev_attr_update_interval.attr, > + NULL > +}; > + > +static const struct attribute_group lm95245_group = { > + .attrs = lm95245_attributes, > +}; > + > +/* Return 0 if detection is successful, -ENODEV otherwise */ > +static int lm95245_detect(struct i2c_client *new_client, > + struct i2c_board_info *info) > +{ > + struct i2c_adapter *adapter = new_client->adapter; > + > + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) > + return -ENODEV; > + > + if (i2c_smbus_read_byte_data(new_client, LM95245_REG_R_MAN_ID) > + != MANUFACTURER_ID > + || i2c_smbus_read_byte_data(new_client, LM95245_REG_R_CHIP_ID) > + != DEFAULT_REVISION) > + return -ENODEV; > + > + strlcpy(info->type, DEVNAME, I2C_NAME_SIZE); > + return 0; > +} > + > +static void lm95245_init_client(struct i2c_client *client) > +{ > + struct lm95245_data *data = i2c_get_clientdata(client); > + > + data->interval = 1000; /* 1 sec default */ Same as config1 applies here - the default interval is 1s, so any change must have been on purpose. As such, it might make sense to read the conversion interval register and set data->interval accordingly. > + data->valid = 0; > + > + data->config1 = i2c_smbus_read_byte_data(client, > + LM95245_REG_RW_CONFIG1); > + data->config2 = i2c_smbus_read_byte_data(client, > + LM95245_REG_RW_CONFIG2); > + > + /* Clear the standby bit */ > + data->config1 &= ~CFG_STOP; > + > + i2c_smbus_write_byte_data(client, LM95245_REG_RW_CONFIG1, > + data->config1); This write is only necessary if the configuration actually changed. Since I2C writes are a bit slow, it makes sense to skip them if unnecessary. Something like if (data->config1 & CFG_STOP) { data->config1 &= ~CFG_STOP; i2c_smbus_write_byte_data(client, LM95245_REG_RW_CONFIG1, data->config1); } would be a bit more efficient. > + lm95245_set_conversion_rate(client, data->interval); you don't need to call this function unless the interval actually changed. In other words, you don't need it if you read the conversion interval above. > +} > + > +static int lm95245_probe(struct i2c_client *new_client, > + const struct i2c_device_id *id) > +{ > + struct lm95245_data *data; > + int err; > + > + data = kzalloc(sizeof(struct lm95245_data), GFP_KERNEL); > + if (!data) { > + err = -ENOMEM; > + goto exit; > + } > + > + i2c_set_clientdata(new_client, data); > + mutex_init(&data->update_lock); > + > + /* Initialize the LM95245 chip */ > + lm95245_init_client(new_client); > + > + /* Register sysfs hooks */ > + err = sysfs_create_group(&new_client->dev.kobj, &lm95245_group); > + if (err) > + goto exit_free; > + > + data->hwmon_dev = hwmon_device_register(&new_client->dev); > + if (IS_ERR(data->hwmon_dev)) { > + err = PTR_ERR(data->hwmon_dev); > + goto exit_remove_files; > + } > + > + return 0; > + > +exit_remove_files: > + sysfs_remove_group(&new_client->dev.kobj, &lm95245_group); > +exit_free: > + kfree(data); > +exit: > + return err; > +} > + > +static int lm95245_remove(struct i2c_client *client) > +{ > + struct lm95245_data *data = i2c_get_clientdata(client); > + > + hwmon_device_unregister(data->hwmon_dev); > + sysfs_remove_group(&client->dev.kobj, &lm95245_group); > + > + kfree(data); > + return 0; > +} > + > +/* Driver data (common to all clients) */ > +static const struct i2c_device_id lm95245_id[] = { > + { DEVNAME, 0 }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, lm95245_id); > + > +static struct i2c_driver lm95245_driver = { > + .class = I2C_CLASS_HWMON, > + .driver = { > + .name = DEVNAME, > + }, > + .probe = lm95245_probe, > + .remove = lm95245_remove, > + .id_table = lm95245_id, > + .detect = lm95245_detect, > + .address_list = normal_i2c, > +}; > + > +static int __init sensors_lm95245_init(void) > +{ > + return i2c_add_driver(&lm95245_driver); > +} > + > +static void __exit sensors_lm95245_exit(void) > +{ > + i2c_del_driver(&lm95245_driver); > +} > + > +MODULE_AUTHOR("Alexander Stein "); > +MODULE_DESCRIPTION("LM95245 sensor driver"); > +MODULE_LICENSE("GPL"); > + > +module_init(sensors_lm95245_init); > +module_exit(sensors_lm95245_exit); > -- > 1.7.3.4 > -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/