Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S933580Ab2BBXv6 (ORCPT ); Thu, 2 Feb 2012 18:51:58 -0500 Received: from xes-mad.com ([216.165.139.218]:47157 "EHLO xes-mad.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1754987Ab2BBXvz (ORCPT ); Thu, 2 Feb 2012 18:51:55 -0500 X-Greylist: delayed 1584 seconds by postgrey-1.27 at vger.kernel.org; Thu, 02 Feb 2012 18:51:54 EST Date: Thu, 02 Feb 2012 17:27:54 -0600 (CST) From: Aaron Sierra To: guenter roeck Cc: Jean Delvare , Grant Likely , LKML , Peter Tyser Subject: [PATCH 2/3] gpio: Add support for Intel ICHx/3100/Series[56] GPIO Message-ID: In-Reply-To: <1328220172.2261.162.camel@groeck-laptop> Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit MIME-Version: 1.0 X-Originating-IP: [10.52.0.65] X-Mailer: Zimbra 7.1.3_GA_3346 (ZimbraWebClient - GC15 (Linux)/7.1.3_GA_3346) Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 14602 Lines: 521 This driver works on many Intel chipsets, including the ICH6, ICH7, ICH8, ICH9, ICH10, 3100, Series 5/3400 (Ibex Peak), Series 6/C200 (Cougar Point), and NM10 (Tiger Point). Additional Intel chipsets should be easily supported if needed, eg the ICH1-5, EP80579, etc. Tested on QM67 (Cougar Point), QM57 (Ibex Peak), 3100 (Whitmore Lake), and NM10 (Tiger Point). Signed-off-by: Peter Tyser --- MAINTAINERS | 6 + drivers/gpio/Kconfig | 16 ++ drivers/gpio/Makefile | 1 + drivers/gpio/ich_gpio.c | 433 +++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 456 insertions(+), 0 deletions(-) create mode 100644 drivers/gpio/ich_gpio.c diff --git a/MAINTAINERS b/MAINTAINERS index 5738c8b..4905dd9 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3160,6 +3160,12 @@ W: http://www.developer.ibm.com/welcome/netfinity/serveraid.html S: Supported F: drivers/scsi/ips.* +ICH LPC DRIVER +M: Peter Tyser +S: Maintained +F: drivers/mfd/ich_lpc.c +F: drivers/gpio/ich_gpio.c + IDE SUBSYSTEM M: "David S. Miller" L: linux-ide@vger.kernel.org diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 2967002..5ae654d 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -140,6 +140,22 @@ config GPIO_SCH This driver can also be built as a module. If so, the module will be called sch-gpio. +config GPIO_ICH + tristate "Intel ICH GPIO" + depends on PCI && X86 + select MFD_CORE + select LPC_ICH + help + Say yes here to support the GPIO functionality of a number of Intel + ICH-based chipsets. Currently supported devices: ICH6, ICH7, ICH8 + ICH9, ICH10, Series 5/3400 (eg Ibex Peak), Series 6/C200 (eg + Cougar Point), NM10 (Tiger Point), and 3100 (Whitmore Lake). + + If unsure, say N. + + This driver can also be built as a module. If so, the module + will be called ich-gpio. + config GPIO_VX855 tristate "VIA VX855/VX875 GPIO" depends on MFD_SUPPORT && PCI diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index b605f8e..840a654 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -39,6 +39,7 @@ obj-$(CONFIG_GPIO_WM831X) += wm831x-gpio.o obj-$(CONFIG_GPIO_WM8350) += wm8350-gpiolib.o obj-$(CONFIG_GPIO_WM8994) += wm8994-gpio.o obj-$(CONFIG_GPIO_SCH) += sch_gpio.o +obj-$(CONFIG_GPIO_ICH) += ich_gpio.o obj-$(CONFIG_MACH_U300) += gpio-u300.o obj-$(CONFIG_PLAT_NOMADIK) += gpio-nomadik.o obj-$(CONFIG_GPIO_RDC321X) += rdc321x-gpio.o diff --git a/drivers/gpio/ich_gpio.c b/drivers/gpio/ich_gpio.c new file mode 100644 index 0000000..f7feca1 --- /dev/null +++ b/drivers/gpio/ich_gpio.c @@ -0,0 +1,433 @@ +/* + * Intel ICH6-10, Series 5 and 6 GPIO driver + * + * Copyright (C) 2010 Extreme Engineering Solutions. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include +#include +#include +#include +#include + +#define DRV_NAME "ich_gpio" + +/* PCI config register offsets into LPC I/F - D31:F0 */ +#define PCI_ICHX_ACPI_BAR 0x40 +#define PCI_ICHX_GPIO_BAR 0x48 +#define PCI_ICHX_GPIO_CTRL 0x4C + +/* + * GPIO register offsets in GPIO I/O space. + * Each chunk of 32 GPIOs is manipulated via its own USE_SELx, IO_SELx, and + * LVLx registers. Logic in the read/write functions takes a register and + * an absolute bit number and determines the proper register offset and bit + * number in that register. For example, to read the value of GPIO bit 50 + * the code would access offset ichx_regs[2(=GPIO_LVL)][1(=50/32)], + * bit 18 (50%32). + */ +enum GPIO_REG { + GPIO_USE_SEL = 0, + GPIO_IO_SEL, + GPIO_LVL, +}; + +static const u8 ichx_regs[3][3] = { + {0x00, 0x30, 0x40}, /* USE_SEL[1-3] offsets */ + {0x04, 0x34, 0x44}, /* IO_SEL[1-3] offsets */ + {0x0c, 0x38, 0x48}, /* LVL[1-3] offsets */ +}; + +#define ICHX_GPIO_WRITE(val, reg) outl(val, (reg) + ichx_priv.gpio_base.start) +#define ICHX_GPIO_READ(reg) inl((reg) + ichx_priv.gpio_base.start) +#define ICHX_PM_WRITE(val, reg) outl(val, (reg) + ichx_priv.pm_base.start) +#define ICHX_PM_READ(reg) inl((reg) + ichx_priv.pm_base.start) + +/* Convenient wrapper to make our PCI ID table */ +#define ICHX_GPIO_PCI_DEVICE(dev, data) \ + .vendor = PCI_VENDOR_ID_INTEL, \ + .device = dev, \ + .subvendor = PCI_ANY_ID, \ + .subdevice = PCI_ANY_ID, \ + .class = 0, \ + .class_mask = 0, \ + .driver_data = (ulong)data + +struct ichx_desc { + /* Max GPIO pins the chipset can have */ + uint ngpio; + + /* The offset of GPE0_STS in the PM IO region, 0 if unneeded */ + uint gpe0_sts_ofs; + + /* USE_SEL is bogus on some chipsets, eg 3100 */ + u32 use_sel_ignore[3]; + + /* Some chipsets have quirks, let these use their own request/get */ + int (*request)(struct gpio_chip *chip, unsigned offset); + int (*get)(struct gpio_chip *chip, unsigned offset); +}; + +static struct { + spinlock_t lock; + struct platform_device *dev; + struct pci_dev *pdev; + struct gpio_chip chip; + struct resource gpio_base; /* GPIO IO base */ + struct resource pm_base; /* Power Mangagment IO base */ + struct ichx_desc *desc; /* Pointer to chipset-specific description */ + u32 orig_gpio_ctrl; /* Orig CTRL value, used to restore on exit */ +} ichx_priv; + +static int modparam_gpiobase = -1; /* dynamic */ +module_param_named(gpiobase, modparam_gpiobase, int, 0444); +MODULE_PARM_DESC(gpiobase, "The GPIO number base. -1 means dynamic, " + "which is the default."); + +static int ichx_write_bit(int reg, unsigned nr, int val, int verify) +{ + unsigned long flags; + u32 data; + int reg_nr = nr / 32; + int bit = nr & 0x1f; + int ret = 0; + + spin_lock_irqsave(&ichx_priv.lock, flags); + + data = ICHX_GPIO_READ(ichx_regs[reg][reg_nr]); + data = (data & ~(1 << bit)) | (val << bit); + ICHX_GPIO_WRITE(data, ichx_regs[reg][reg_nr]); + if (verify && (data != ICHX_GPIO_READ(ichx_regs[reg][reg_nr]))) + ret = -EPERM; + + spin_unlock_irqrestore(&ichx_priv.lock, flags); + + return ret; +} + +static int ichx_read_bit(int reg, unsigned nr) +{ + unsigned long flags; + u32 data; + int reg_nr = nr / 32; + int bit = nr & 0x1f; + + spin_lock_irqsave(&ichx_priv.lock, flags); + + data = ICHX_GPIO_READ(ichx_regs[reg][reg_nr]); + + spin_unlock_irqrestore(&ichx_priv.lock, flags); + + return data & (1 << bit) ? 1 : 0; +} + +static int ichx_gpio_direction_input(struct gpio_chip *gpio, unsigned nr) +{ + /* + * Try setting pin as an input and verify it worked since many pins + * are output-only. + */ + if (ichx_write_bit(GPIO_IO_SEL, nr, 1, 1)) + return -EINVAL; + + return 0; +} + +static int ichx_gpio_direction_output(struct gpio_chip *gpio, unsigned nr, + int val) +{ + /* Set GPIO output value. */ + ichx_write_bit(GPIO_LVL, nr, val, 0); + + /* + * Try setting pin as an output and verify it worked since many pins + * are input-only. + */ + if (ichx_write_bit(GPIO_IO_SEL, nr, 0, 1)) + return -EINVAL; + + return 0; +} + +static int ichx_gpio_get(struct gpio_chip *chip, unsigned nr) +{ + return ichx_read_bit(GPIO_LVL, nr); +} + +static int ich6_gpio_get(struct gpio_chip *chip, unsigned nr) +{ + unsigned long flags; + u32 data; + + /* + * GPI 0 - 15 need to be read from the power management registers on + * a ICH6/3100 bridge. + */ + if (nr < 16) { + spin_lock_irqsave(&ichx_priv.lock, flags); + + /* GPI 0 - 15 are latched, write 1 to clear*/ + ICHX_PM_WRITE(1 << (16 + nr), ichx_priv.desc->gpe0_sts_ofs); + + data = ICHX_PM_READ(ichx_priv.desc->gpe0_sts_ofs); + + spin_unlock_irqrestore(&ichx_priv.lock, flags); + + return (data >> 16) & (1 << nr) ? 1 : 0; + } else { + return ichx_gpio_get(chip, nr); + } +} + +static int ichx_gpio_request(struct gpio_chip *chip, unsigned nr) +{ + /* + * Note we assume the BIOS properly set a bridge's USE value. Some + * chips (eg Intel 3100) have bogus USE values though, so first see if + * the chipset's USE value can be trusted for this specific bit. + * If it can't be trusted, assume that the pin can be used as a GPIO. + */ + if (ichx_priv.desc->use_sel_ignore[nr / 32] & (1 << (nr & 0x1f))) + return 1; + + return ichx_read_bit(GPIO_USE_SEL, nr) ? 0 : -ENODEV; +} + +static int ich6_gpio_request(struct gpio_chip *chip, unsigned nr) +{ + /* + * Fixups for bits 16 and 17 are necessary on the Intel ICH6/3100 + * bridge as they are controlled by USE register bits 0 and 1. See + * "Table 704 GPIO_USE_SEL1 register" in the i3100 datasheet for + * additional info. + */ + if ((nr == 16) || (nr == 17)) + nr -= 16; + + return ichx_gpio_request(chip, nr); +} + +static void ichx_gpio_set(struct gpio_chip *chip, unsigned nr, int val) +{ + ichx_write_bit(GPIO_LVL, nr, val, 0); +} + +static void __devinit ichx_gpiolib_setup(struct gpio_chip *chip) +{ + chip->owner = THIS_MODULE; + chip->label = DRV_NAME; + + /* Allow chip-specific overrides of request()/get() */ + chip->request = ichx_priv.desc->request ? + ichx_priv.desc->request : ichx_gpio_request; + chip->get = ichx_priv.desc->get ? + ichx_priv.desc->get : ichx_gpio_get; + + chip->set = ichx_gpio_set; + chip->direction_input = ichx_gpio_direction_input; + chip->direction_output = ichx_gpio_direction_output; + chip->base = modparam_gpiobase; + chip->ngpio = ichx_priv.desc->ngpio; + chip->can_sleep = 0; + chip->dbg_show = NULL; +} + +/* ICH6-based, 631xesb-based */ +static struct ichx_desc ich6_desc = { + /* Bridges using the ICH6 controller need fixups for GPIO 0 - 17 */ + .request = ich6_gpio_request, + .get = ich6_gpio_get, + + /* GPIO 0-15 are read in the GPE0_STS PM register */ + .gpe0_sts_ofs = 0x28, + + .ngpio = 50, +}; + +/* Intel 3100 */ +static struct ichx_desc i3100_desc = { + /* + * Bits 16,17, 20 of USE_SEL and bit 16 of USE_SEL2 always read 0 on + * the Intel 3100. See "Table 712. GPIO Summary Table" of 3100 + * Datasheet for more info. + */ + .use_sel_ignore = {0x00130000, 0x00010000, 0x0}, + + /* The 3100 needs fixups for GPIO 0 - 17 */ + .request = ich6_gpio_request, + .get = ich6_gpio_get, + + /* GPIO 0-15 are read in the GPE0_STS PM register */ + .gpe0_sts_ofs = 0x28, + + .ngpio = 50, +}; + +/* ICH7 and ICH8-based */ +static struct ichx_desc ich7_desc = { + .ngpio = 50, +}; + +/* ICH9-based */ +static struct ichx_desc ich9_desc = { + .ngpio = 61, +}; + +/* ICH10-based - Consumer/corporate versions have different amount of GPIO */ +static struct ichx_desc ich10_cons_desc = { + .ngpio = 51, +}; +static struct ichx_desc ich10_corp_desc = { + .ngpio = 72, +}; + +/* Intel 5 series, 6 series, 3400 series, and C200 series */ +static struct ichx_desc intel5_desc = { + .ngpio = 76, +}; + +static int __devinit ichx_gpio_probe(struct platform_device *pdev) +{ + struct resource *res_base, *res_pm; + size_t sz_base; + int id; + int err; + + id = pdev->id; + if (!id) + return -ENODEV; + + switch (lpc_chipset_info[id].gpio_version) { + case 0x401: + ichx_priv.desc = &i3100_desc; + break; + case 0x501: + ichx_priv.desc = &intel5_desc; + break; + case 0x601: + ichx_priv.desc = &ich6_desc; + break; + case 0x701: + ichx_priv.desc = &ich7_desc; + break; + case 0x801: + ichx_priv.desc = &ich9_desc; + break; + case 0xa01: + ichx_priv.desc = &ich10_corp_desc; + break; + case 0xa11: + ichx_priv.desc = &ich10_cons_desc; + break; + default: + goto base_err; + } + + res_base = platform_get_resource(pdev, IORESOURCE_IO, ICH_RES_GPIO); + if (!res_base) + goto base_err; + + sz_base = ichx_priv.desc->ngpio > 64 ? resource_size(res_base) : 64; + if (!request_region(res_base->start, sz_base, pdev->name)) + goto base_err; + + memcpy(&ichx_priv.gpio_base, res_base, sizeof(struct resource)); + ichx_priv.gpio_base.end = ichx_priv.gpio_base.end + sz_base; + + /* + * If necessary, determine the I/O address of ACPI/power management + * registers which are needed to read the the GPE0 register for GPI pins + * 0 - 15 on some chipsets. + */ + if (!ichx_priv.desc->gpe0_sts_ofs) + goto init; + + res_pm = platform_get_resource(pdev, IORESOURCE_IO, ICH_RES_GPE0); + if (!res_pm) { + pr_warn("ACPI BAR not enumerated, GPI 0 - 15 " + "unusable\n"); + goto init; + } + + if (!request_region(res_pm->start, resource_size(res_pm), + pdev->name)) { + pr_warn("ACPI BAR not enumerated, GPI 0 - 15 " + "unusable\n"); + goto init; + } + + memcpy(&ichx_priv.pm_base, res_pm, sizeof(struct resource)); + +init: + ichx_gpiolib_setup(&ichx_priv.chip); + err = gpiochip_add(&ichx_priv.chip); + if (err) { + pr_err("Failed to register GPIOs\n"); + return err; + } + + pr_info("GPIO from %d to %d on %s\n", ichx_priv.chip.base, + ichx_priv.chip.base + ichx_priv.chip.ngpio - 1, DRV_NAME); + + return 0; + +base_err: + return -ENODEV; +} + +static int __devexit ichx_gpio_remove(struct platform_device *pdev) +{ + int err; + + err = gpiochip_remove(&ichx_priv.chip); + if (err) + dev_err(&pdev->dev, "%s failed, %d\n", + "gpiochip_remove()", err); + + err = release_resource(&ichx_priv.gpio_base); + + return err; +} + +static struct platform_driver ichx_gpio_driver = { + .driver = { + .owner = THIS_MODULE, + .name = DRV_NAME, + }, + .probe = ichx_gpio_probe, + .remove = __devexit_p(ichx_gpio_remove), +}; + +static int __devinit ichx_gpio_init_module(void) +{ + return platform_driver_register(&ichx_gpio_driver); +} + +static void __devexit ichx_gpio_exit_module(void) +{ + platform_driver_unregister(&ichx_gpio_driver); +} + +module_init(ichx_gpio_init_module); +module_exit(ichx_gpio_exit_module); + +MODULE_AUTHOR("Peter Tyser "); +MODULE_DESCRIPTION("GPIO interface for Intel ICH series"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:ich_gpio"); -- 1.7.0.4 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/