Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1756946Ab2EYJio (ORCPT ); Fri, 25 May 2012 05:38:44 -0400 Received: from terminus.zytor.com ([198.137.202.10]:36986 "EHLO terminus.zytor.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1756773Ab2EYJii (ORCPT ); Fri, 25 May 2012 05:38:38 -0400 Date: Fri, 25 May 2012 02:38:22 -0700 From: tip-bot for Magnus Damm Message-ID: Cc: linux-kernel@vger.kernel.org, hpa@zytor.com, mingo@kernel.org, damm@opensource.se, tglx@linutronix.de, magnus.damm@gmail.com Reply-To: mingo@kernel.org, hpa@zytor.com, linux-kernel@vger.kernel.org, damm@opensource.se, tglx@linutronix.de, magnus.damm@gmail.com In-Reply-To: <20120525070344.23443.69756.sendpatchset@w520> References: <20120525070344.23443.69756.sendpatchset@w520> To: linux-tip-commits@vger.kernel.org Subject: [tip:timers/core] clocksource: em_sti: Emma Mobile STI driver Git-Commit-ID: b9dbf9517784084ee9496f9f17f9754c1d021a9e X-Mailer: tip-git-log-daemon Robot-ID: Robot-Unsubscribe: Contact to get blacklisted from these emails MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Content-Type: text/plain; charset=UTF-8 Content-Disposition: inline X-Greylist: Sender IP whitelisted, not delayed by milter-greylist-4.2.6 (terminus.zytor.com [127.0.0.1]); Fri, 25 May 2012 02:38:28 -0700 (PDT) Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 12640 Lines: 474 Commit-ID: b9dbf9517784084ee9496f9f17f9754c1d021a9e Gitweb: http://git.kernel.org/tip/b9dbf9517784084ee9496f9f17f9754c1d021a9e Author: Magnus Damm AuthorDate: Fri, 25 May 2012 16:03:44 +0900 Committer: Thomas Gleixner CommitDate: Fri, 25 May 2012 11:32:06 +0200 clocksource: em_sti: Emma Mobile STI driver The STI hardware is based on a single 48-bit 32kHz counter that together with two individual compare registers can generate interrupts. There are no timer operating modes selectable which means that the timer can not clear on match. This driver is providing clocksource support for the 48-bit counter. Clockevents are also supported using the same timer in oneshot mode. Signed-off-by: Magnus Damm Cc: horms@verge.net.au Cc: arnd@arndb.de Cc: johnstul@us.ibm.com Cc: rjw@sisk.pl Cc: lethal@linux-sh.org Cc: gregkh@linuxfoundation.org Cc: olof@lixom.net Link: http://lkml.kernel.org/r/20120525070344.23443.69756.sendpatchset@w520 Signed-off-by: Thomas Gleixner --- arch/arm/mach-shmobile/Kconfig | 6 + drivers/clocksource/Makefile | 1 + drivers/clocksource/em_sti.c | 399 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 406 insertions(+), 0 deletions(-) diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig index f31383c..df33909 100644 --- a/arch/arm/mach-shmobile/Kconfig +++ b/arch/arm/mach-shmobile/Kconfig @@ -186,6 +186,12 @@ config SH_TIMER_TMU help This enables build of the TMU timer driver. +config EM_TIMER_STI + bool "STI timer driver" + default y + help + This enables build of the STI timer driver. + endmenu config SH_CLK_CPG diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile index 8d81a1d..dd3e661 100644 --- a/drivers/clocksource/Makefile +++ b/drivers/clocksource/Makefile @@ -6,6 +6,7 @@ obj-$(CONFIG_CS5535_CLOCK_EVENT_SRC) += cs5535-clockevt.o obj-$(CONFIG_SH_TIMER_CMT) += sh_cmt.o obj-$(CONFIG_SH_TIMER_MTU2) += sh_mtu2.o obj-$(CONFIG_SH_TIMER_TMU) += sh_tmu.o +obj-$(CONFIG_EM_TIMER_STI) += em_sti.o obj-$(CONFIG_CLKBLD_I8253) += i8253.o obj-$(CONFIG_CLKSRC_MMIO) += mmio.o obj-$(CONFIG_DW_APB_TIMER) += dw_apb_timer.o diff --git a/drivers/clocksource/em_sti.c b/drivers/clocksource/em_sti.c new file mode 100644 index 0000000..719584a --- /dev/null +++ b/drivers/clocksource/em_sti.c @@ -0,0 +1,399 @@ +/* + * Emma Mobile Timer Support - STI + * + * Copyright (C) 2012 Magnus Damm + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +enum { USER_CLOCKSOURCE, USER_CLOCKEVENT, USER_NR }; + +struct em_sti_priv { + void __iomem *base; + struct clk *clk; + struct platform_device *pdev; + unsigned int active[USER_NR]; + unsigned long rate; + raw_spinlock_t lock; + struct clock_event_device ced; + struct clocksource cs; +}; + +#define STI_CONTROL 0x00 +#define STI_COMPA_H 0x10 +#define STI_COMPA_L 0x14 +#define STI_COMPB_H 0x18 +#define STI_COMPB_L 0x1c +#define STI_COUNT_H 0x20 +#define STI_COUNT_L 0x24 +#define STI_COUNT_RAW_H 0x28 +#define STI_COUNT_RAW_L 0x2c +#define STI_SET_H 0x30 +#define STI_SET_L 0x34 +#define STI_INTSTATUS 0x40 +#define STI_INTRAWSTATUS 0x44 +#define STI_INTENSET 0x48 +#define STI_INTENCLR 0x4c +#define STI_INTFFCLR 0x50 + +static inline unsigned long em_sti_read(struct em_sti_priv *p, int offs) +{ + return ioread32(p->base + offs); +} + +static inline void em_sti_write(struct em_sti_priv *p, int offs, + unsigned long value) +{ + iowrite32(value, p->base + offs); +} + +static int em_sti_enable(struct em_sti_priv *p) +{ + int ret; + + /* enable clock */ + ret = clk_enable(p->clk); + if (ret) { + dev_err(&p->pdev->dev, "cannot enable clock\n"); + return ret; + } + + /* configure channel, periodic mode and maximum timeout */ + p->rate = clk_get_rate(p->clk); + + /* reset the counter */ + em_sti_write(p, STI_SET_H, 0x40000000); + em_sti_write(p, STI_SET_L, 0x00000000); + + /* mask and clear pending interrupts */ + em_sti_write(p, STI_INTENCLR, 3); + em_sti_write(p, STI_INTFFCLR, 3); + + /* enable updates of counter registers */ + em_sti_write(p, STI_CONTROL, 1); + + return 0; +} + +static void em_sti_disable(struct em_sti_priv *p) +{ + /* mask interrupts */ + em_sti_write(p, STI_INTENCLR, 3); + + /* stop clock */ + clk_disable(p->clk); +} + +static cycle_t em_sti_count(struct em_sti_priv *p) +{ + cycle_t ticks; + unsigned long flags; + + /* the STI hardware buffers the 48-bit count, but to + * break it out into two 32-bit access the registers + * must be accessed in a certain order. + * Always read STI_COUNT_H before STI_COUNT_L. + */ + raw_spin_lock_irqsave(&p->lock, flags); + ticks = (cycle_t)(em_sti_read(p, STI_COUNT_H) & 0xffff) << 32; + ticks |= em_sti_read(p, STI_COUNT_L); + raw_spin_unlock_irqrestore(&p->lock, flags); + + return ticks; +} + +static cycle_t em_sti_set_next(struct em_sti_priv *p, cycle_t next) +{ + unsigned long flags; + + raw_spin_lock_irqsave(&p->lock, flags); + + /* mask compare A interrupt */ + em_sti_write(p, STI_INTENCLR, 1); + + /* update compare A value */ + em_sti_write(p, STI_COMPA_H, next >> 32); + em_sti_write(p, STI_COMPA_L, next & 0xffffffff); + + /* clear compare A interrupt source */ + em_sti_write(p, STI_INTFFCLR, 1); + + /* unmask compare A interrupt */ + em_sti_write(p, STI_INTENSET, 1); + + raw_spin_unlock_irqrestore(&p->lock, flags); + + return next; +} + +static irqreturn_t em_sti_interrupt(int irq, void *dev_id) +{ + struct em_sti_priv *p = dev_id; + + p->ced.event_handler(&p->ced); + return IRQ_HANDLED; +} + +static int em_sti_start(struct em_sti_priv *p, unsigned int user) +{ + unsigned long flags; + int used_before; + int ret = 0; + + raw_spin_lock_irqsave(&p->lock, flags); + used_before = p->active[USER_CLOCKSOURCE] | p->active[USER_CLOCKEVENT]; + if (!used_before) + ret = em_sti_enable(p); + + if (!ret) + p->active[user] = 1; + raw_spin_unlock_irqrestore(&p->lock, flags); + + return ret; +} + +static void em_sti_stop(struct em_sti_priv *p, unsigned int user) +{ + unsigned long flags; + int used_before, used_after; + + raw_spin_lock_irqsave(&p->lock, flags); + used_before = p->active[USER_CLOCKSOURCE] | p->active[USER_CLOCKEVENT]; + p->active[user] = 0; + used_after = p->active[USER_CLOCKSOURCE] | p->active[USER_CLOCKEVENT]; + + if (used_before && !used_after) + em_sti_disable(p); + raw_spin_unlock_irqrestore(&p->lock, flags); +} + +static struct em_sti_priv *cs_to_em_sti(struct clocksource *cs) +{ + return container_of(cs, struct em_sti_priv, cs); +} + +static cycle_t em_sti_clocksource_read(struct clocksource *cs) +{ + return em_sti_count(cs_to_em_sti(cs)); +} + +static int em_sti_clocksource_enable(struct clocksource *cs) +{ + int ret; + struct em_sti_priv *p = cs_to_em_sti(cs); + + ret = em_sti_start(p, USER_CLOCKSOURCE); + if (!ret) + __clocksource_updatefreq_hz(cs, p->rate); + return ret; +} + +static void em_sti_clocksource_disable(struct clocksource *cs) +{ + em_sti_stop(cs_to_em_sti(cs), USER_CLOCKSOURCE); +} + +static void em_sti_clocksource_resume(struct clocksource *cs) +{ + em_sti_clocksource_enable(cs); +} + +static int em_sti_register_clocksource(struct em_sti_priv *p) +{ + struct clocksource *cs = &p->cs; + + memset(cs, 0, sizeof(*cs)); + cs->name = dev_name(&p->pdev->dev); + cs->rating = 200; + cs->read = em_sti_clocksource_read; + cs->enable = em_sti_clocksource_enable; + cs->disable = em_sti_clocksource_disable; + cs->suspend = em_sti_clocksource_disable; + cs->resume = em_sti_clocksource_resume; + cs->mask = CLOCKSOURCE_MASK(48); + cs->flags = CLOCK_SOURCE_IS_CONTINUOUS; + + dev_info(&p->pdev->dev, "used as clock source\n"); + + /* Register with dummy 1 Hz value, gets updated in ->enable() */ + clocksource_register_hz(cs, 1); + return 0; +} + +static struct em_sti_priv *ced_to_em_sti(struct clock_event_device *ced) +{ + return container_of(ced, struct em_sti_priv, ced); +} + +static void em_sti_clock_event_mode(enum clock_event_mode mode, + struct clock_event_device *ced) +{ + struct em_sti_priv *p = ced_to_em_sti(ced); + + /* deal with old setting first */ + switch (ced->mode) { + case CLOCK_EVT_MODE_ONESHOT: + em_sti_stop(p, USER_CLOCKEVENT); + break; + default: + break; + } + + switch (mode) { + case CLOCK_EVT_MODE_ONESHOT: + dev_info(&p->pdev->dev, "used for oneshot clock events\n"); + em_sti_start(p, USER_CLOCKEVENT); + clockevents_config(&p->ced, p->rate); + break; + case CLOCK_EVT_MODE_SHUTDOWN: + case CLOCK_EVT_MODE_UNUSED: + em_sti_stop(p, USER_CLOCKEVENT); + break; + default: + break; + } +} + +static int em_sti_clock_event_next(unsigned long delta, + struct clock_event_device *ced) +{ + struct em_sti_priv *p = ced_to_em_sti(ced); + cycle_t next; + int safe; + + next = em_sti_set_next(p, em_sti_count(p) + delta); + safe = em_sti_count(p) < (next - 1); + + return !safe; +} + +static void em_sti_register_clockevent(struct em_sti_priv *p) +{ + struct clock_event_device *ced = &p->ced; + + memset(ced, 0, sizeof(*ced)); + ced->name = dev_name(&p->pdev->dev); + ced->features = CLOCK_EVT_FEAT_ONESHOT; + ced->rating = 200; + ced->cpumask = cpumask_of(0); + ced->set_next_event = em_sti_clock_event_next; + ced->set_mode = em_sti_clock_event_mode; + + dev_info(&p->pdev->dev, "used for clock events\n"); + + /* Register with dummy 1 Hz value, gets updated in ->set_mode() */ + clockevents_config_and_register(ced, 1, 2, 0xffffffff); +} + +static int __devinit em_sti_probe(struct platform_device *pdev) +{ + struct em_sti_priv *p; + struct resource *res; + int irq, ret; + + p = kzalloc(sizeof(*p), GFP_KERNEL); + if (p == NULL) { + dev_err(&pdev->dev, "failed to allocate driver data\n"); + ret = -ENOMEM; + goto err0; + } + + p->pdev = pdev; + platform_set_drvdata(pdev, p); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "failed to get I/O memory\n"); + ret = -EINVAL; + goto err0; + } + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "failed to get irq\n"); + ret = -EINVAL; + goto err0; + } + + /* map memory, let base point to the STI instance */ + p->base = ioremap_nocache(res->start, resource_size(res)); + if (p->base == NULL) { + dev_err(&pdev->dev, "failed to remap I/O memory\n"); + ret = -ENXIO; + goto err0; + } + + /* get hold of clock */ + p->clk = clk_get(&pdev->dev, "sclk"); + if (IS_ERR(p->clk)) { + dev_err(&pdev->dev, "cannot get clock\n"); + ret = PTR_ERR(p->clk); + goto err1; + } + + if (request_irq(irq, em_sti_interrupt, + IRQF_TIMER | IRQF_IRQPOLL | IRQF_NOBALANCING, + dev_name(&pdev->dev), p)) { + dev_err(&pdev->dev, "failed to request low IRQ\n"); + ret = -ENOENT; + goto err2; + } + + raw_spin_lock_init(&p->lock); + em_sti_register_clockevent(p); + em_sti_register_clocksource(p); + return 0; + +err2: + clk_put(p->clk); +err1: + iounmap(p->base); +err0: + kfree(p); + return ret; +} + +static int __devexit em_sti_remove(struct platform_device *pdev) +{ + return -EBUSY; /* cannot unregister clockevent and clocksource */ +} + +static struct platform_driver em_sti_device_driver = { + .probe = em_sti_probe, + .remove = __devexit_p(em_sti_remove), + .driver = { + .name = "em_sti", + } +}; + +module_platform_driver(em_sti_device_driver); + +MODULE_AUTHOR("Magnus Damm"); +MODULE_DESCRIPTION("Renesas Emma Mobile STI Timer Driver"); +MODULE_LICENSE("GPL v2"); -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/