Summary: The Promise Ultra100TX2 doesn't work for me in 2.6.0-test9 -
but it is fine with 2.4.18xfs
(First posting to lkml - hopefully got enough info and this will be
helpful - let me know if you need more.)
I've been googling, recompiling and trying for 12 hours now so I've seen
a lot of stuff about the promise drivers :)
My basic system is RedHat 7.3 with XFS. The kernel is non std (has XFS +
misc ACL patch) 2.4.18
I am using the 80pin cable supplied with the Promise.
I've tried the 'noapic' option (and config'ed without any power
management) as Alan Cox suggested
Below is trimmed dmesg from 2.4.18 and complete dmesg from 2.6.0-test9
Please cc lkml at dgreaves.com in replies.
grub for 2.4.18: kernel /vmlinuz-2.4.18-4SGI_XFS_1.1customIDE ro
root=/dev/hdc3 ide2=ata66 ide2=autotune
(Relevant bit from 2.4.18 dmesg:
#########################
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
PDC20268: IDE controller on PCI bus 00 dev 48
PCI: Found IRQ 10 for device 00:09.0
PDC20268: chipset revision 2
PDC20268: not 100% native mode: will probe irqs later
PDC20268: ROM enabled at 0xe8000000
PDC20268: ATA-66/100 forced bit set (WARNING)!!
ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
hda: ST320420A, ATA DISK drive
hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
hdc: IBM-DTLA-305040, ATA DISK drive
hdd: IC35L060AVVA07-0, ATA DISK drive
hde: WDC WD800JB-00ETA0, ATA DISK drive
hdf: WDC WD800JB-00ETA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xd800-0xd807,0xdc02 on irq 10
hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=2480/255/63, UDMA(33)
hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=79780/16/63, UDMA(33)
hdd: 120103200 sectors (61493 MB) w/1863KiB Cache, CHS=119150/16/63,
UDMA(33)
blk: queue c02ebdec, I/O limit 4095Mb (mask 0xffffffff)
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/255/63,
UDMA(100)
blk: queue c02ebf38, I/O limit 4095Mb (mask 0xffffffff)
hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/255/63,
UDMA(100)
Partition check:
hda: hda1 hda2
hdc: hdc1 hdc2 hdc3
hdd: hdd1
hde: hde1
hdf: hdf1
[snip]
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
XFS mounting filesystem ide0(3,1)
XFS mounting filesystem ide1(22,65)
XFS mounting filesystem ide1(22,1)
XFS mounting filesystem ide0(3,2)
XFS mounting filesystem ide2(33,1)
XFS mounting filesystem ide2(33,65)
hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
hdb: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdb: packet command error: error=0x00
hdb: DMA disabled
ide0: Speed warnings UDMA 3/4/5 is not functional.
ide1: Speed warnings UDMA 3/4/5 is not functional.
ide1: Speed warnings UDMA 3/4/5 is not functional.
blk: queue c02ebdec, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c02ebf38, I/O limit 4095Mb (mask 0xffffffff)
#########################
and from 2.6.0-test9
#########################
Linux version 2.6.0-test9 (root@willow) (gcc version 2.96 20000731 (Red
Hat Linux 7.3 2.96-110)) #2 Sat Nov 8 15:56:56 GMT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000010ff0000 (usable)
BIOS-e820: 0000000010ff0000 - 0000000010ff3000 (ACPI NVS)
BIOS-e820: 0000000010ff3000 - 0000000011000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
271MB LOWMEM available.
On node 0 totalpages: 69616
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 65520 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
Building zonelist for node : 0
Kernel command line: ro root=/dev/hdc3 noapic single
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 451.117 MHz processor.
Console: colour VGA+ 80x25
Memory: 271812k/278464k available (2117k kernel code, 5936k reserved,
753k data, 120k init, 0k highmem)
Calibrating delay loop... 888.83 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 008021bf 808029bf 00000000 00000000
CPU: After vendor identify, caps: 008021bf 808029bf 00000000 00000000
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: L2 Cache: 256K (32 bytes/line)
CPU: After all inits, caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D+ Processor stepping 01
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb480, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc0c0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc0e8, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0586] at 0000:00:07.0
Machine check exception polling timer started.
Installing knfsd (copyright (C) 1996 [email protected]).
udf: registering filesystem
SGI XFS for Linux with no debug enabled
Activating ISA DMA hang workarounds.
pty: 256 Unix98 ptys configured
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci0000:00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST320420A, ATA DISK drive
hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: IBM-DTLA-305040, ATA DISK drive
hdd: IC35L060AVVA07-0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
PDC20268: IDE controller at PCI slot 0000:00:09.0
PCI: Found IRQ 10 for device 0000:00:09.0
PDC20268: chipset revision 2
PDC20268: ROM enabled at 0xe8000000
PDC20268: 100% native mode on irq 10
ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
hde: WDC WD800JB-00ETA0, ATA DISK drive
hdf: WDC WD800JB-00ETA0, ATA DISK drive
hdf: set_drive_speed_status: status=0xff { Busy }
ide2 at 0xd800-0xd807,0xdc02 on irq 10
hda: max request size: 128KiB
hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=39535/16/63
hda: hda1 hda2
hdc: max request size: 128KiB
hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=65535/16/63
hdc: hdc1 hdc2 hdc3
hdd: max request size: 128KiB
hdd: 120103200 sectors (61492 MB) w/1863KiB Cache, CHS=65535/16/63
hdd: hdd1
hde: max request size: 1024KiB
hde: status timeout: status=0xff { Busy }
hde: drive not ready for command
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63
hde: status timeout: status=0xff { Busy }
hde: drive not ready for command
hde:hde: status timeout: status=0xff { Busy }
PDC202XX: Primary channel reset.
hde: drive not ready for command
ide2: reset timed-out, status=0xff
hde: status timeout: status=0xff { Busy }
PDC202XX: Primary channel reset.
hde: drive not ready for command
ide2: reset timed-out, status=0xff
end_request: I/O error, dev hde, sector 0
Buffer I/O error on device hde, logical block 0
end_request: I/O error, dev hde, sector 0
Buffer I/O error on device hde, logical block 0
unable to read partition table
hdf: max request size: 1024KiB
hdf: status timeout: status=0xff { Busy }
hdf: drive not ready for command
hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63
hdf: status timeout: status=0xff { Busy }
hdf: drive not ready for command
hdf:hdf: status timeout: status=0xff { Busy }
PDC202XX: Primary channel reset.
hdf: drive not ready for command
ide2: reset timed-out, status=0xff
hdf: status timeout: status=0xff { Busy }
PDC202XX: Primary channel reset.
hdf: drive not ready for command
ide2: reset timed-out, status=0xff
end_request: I/O error, dev hdf, sector 0
Buffer I/O error on device hdf, logical block 0
end_request: I/O error, dev hdf, sector 0
Buffer I/O error on device hdf, logical block 0
unable to read partition table
end_request: I/O error, dev hdb, sector 0
hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache
Uniform CD-ROM driver Revision: 3.12
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25
19:16:36 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
UDF-fs DEBUG fs/udf/lowlevel.c:65:udf_get_last_session:
CDROMMULTISESSION not supported: rc=-22
UDF-fs DEBUG fs/udf/super.c:1544:udf_fill_super: Multi-session=0
UDF-fs DEBUG fs/udf/super.c:531:udf_vrs: Starting at sector 16 (2048
byte sectors)
UDF-fs: No VRS found
XFS mounting filesystem hdc3
Ending clean XFS mount for filesystem: hdc3
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 120k freed
Adding 512056k swap on /dev/hdc2. Priority:-1 extents:1
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
XFS mounting filesystem hda1
Ending clean XFS mount for filesystem: hda1
XFS mounting filesystem hdd1
Ending clean XFS mount for filesystem: hdd1
XFS mounting filesystem hdc1
Ending clean XFS mount for filesystem: hdc1
XFS mounting filesystem hda2
Ending clean XFS mount for filesystem: hda2
hdb: DMA disabled
hda: Speed warnings UDMA 3/4/5 is not functional.
ide1: Speed warnings UDMA 3/4/5 is not functional.
ide1: Speed warnings UDMA 3/4/5 is not functional.
end_request: I/O error, dev hde, sector 0
hde: set_drive_speed_status: status=0xff { Busy }
end_request: I/O error, dev hde, sector 0
hde: set_drive_speed_status: status=0xff { Busy }
end_request: I/O error, dev hde, sector 0
end_request: I/O error, dev hdf, sector 0
hdf: set_drive_speed_status: status=0xff { Busy }
end_request: I/O error, dev hdf, sector 0
hdf: set_drive_speed_status: status=0xff { Busy }
end_request: I/O error, dev hdf, sector 0
Hi,
Can you try "ide2=autotune ide3=autotune" boot parameters?
Promise driver is not autotuning PIO modes by default (will be fixed soon,
needs some more testing). You are hitting it only in 2.6.0-t9 because you've
compiled kernel without "DMA on by default" (guess based on your dmesg),
plus in 2.4.18 you are passing "ide2=autotune" parameter.
Off-topic: you have two drives on the first channel, second channel is free.
Why not move one of drives to the second channel?
Please post ide bugreports on [email protected] next time.
thanks,
--bartlomiej
On Saturday 08 of November 2003 17:51, David Greaves wrote:
> Summary: The Promise Ultra100TX2 doesn't work for me in 2.6.0-test9 -
> but it is fine with 2.4.18xfs
>
> (First posting to lkml - hopefully got enough info and this will be
> helpful - let me know if you need more.)
> I've been googling, recompiling and trying for 12 hours now so I've seen
> a lot of stuff about the promise drivers :)
>
> My basic system is RedHat 7.3 with XFS. The kernel is non std (has XFS +
> misc ACL patch) 2.4.18
>
> I am using the 80pin cable supplied with the Promise.
> I've tried the 'noapic' option (and config'ed without any power
> management) as Alan Cox suggested
>
> Below is trimmed dmesg from 2.4.18 and complete dmesg from 2.6.0-test9
>
> Please cc lkml at dgreaves.com in replies.
>
> grub for 2.4.18: kernel /vmlinuz-2.4.18-4SGI_XFS_1.1customIDE ro
> root=/dev/hdc3 ide2=ata66 ide2=autotune
> (Relevant bit from 2.4.18 dmesg:
> #########################
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: IDE controller on PCI bus 00 dev 39
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci00:07.1
> ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
> PDC20268: IDE controller on PCI bus 00 dev 48
> PCI: Found IRQ 10 for device 00:09.0
> PDC20268: chipset revision 2
> PDC20268: not 100% native mode: will probe irqs later
> PDC20268: ROM enabled at 0xe8000000
> PDC20268: ATA-66/100 forced bit set (WARNING)!!
> ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
> hda: ST320420A, ATA DISK drive
> hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
> hdc: IBM-DTLA-305040, ATA DISK drive
> hdd: IC35L060AVVA07-0, ATA DISK drive
> hde: WDC WD800JB-00ETA0, ATA DISK drive
> hdf: WDC WD800JB-00ETA0, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> ide2 at 0xd800-0xd807,0xdc02 on irq 10
> hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=2480/255/63, UDMA(33)
> hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=79780/16/63, UDMA(33)
> hdd: 120103200 sectors (61493 MB) w/1863KiB Cache, CHS=119150/16/63,
> UDMA(33)
> blk: queue c02ebdec, I/O limit 4095Mb (mask 0xffffffff)
> hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/255/63,
> UDMA(100)
> blk: queue c02ebf38, I/O limit 4095Mb (mask 0xffffffff)
> hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/255/63,
> UDMA(100)
> Partition check:
> hda: hda1 hda2
> hdc: hdc1 hdc2 hdc3
> hdd: hdd1
> hde: hde1
> hdf: hdf1
> [snip]
> md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
> XFS mounting filesystem ide0(3,1)
> XFS mounting filesystem ide1(22,65)
> XFS mounting filesystem ide1(22,1)
> XFS mounting filesystem ide0(3,2)
> XFS mounting filesystem ide2(33,1)
> XFS mounting filesystem ide2(33,65)
> hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache, DMA
> Uniform CD-ROM driver Revision: 3.12
> hdb: packet command error: status=0x51 { DriveReady SeekComplete Error }
> hdb: packet command error: error=0x00
> hdb: DMA disabled
> ide0: Speed warnings UDMA 3/4/5 is not functional.
> ide1: Speed warnings UDMA 3/4/5 is not functional.
> ide1: Speed warnings UDMA 3/4/5 is not functional.
> blk: queue c02ebdec, I/O limit 4095Mb (mask 0xffffffff)
> blk: queue c02ebf38, I/O limit 4095Mb (mask 0xffffffff)
> #########################
>
> and from 2.6.0-test9
> #########################
> Linux version 2.6.0-test9 (root@willow) (gcc version 2.96 20000731 (Red
> Hat Linux 7.3 2.96-110)) #2 Sat Nov 8 15:56:56 GMT 2003
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 0000000010ff0000 (usable)
> BIOS-e820: 0000000010ff0000 - 0000000010ff3000 (ACPI NVS)
> BIOS-e820: 0000000010ff3000 - 0000000011000000 (ACPI data)
> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> 271MB LOWMEM available.
> On node 0 totalpages: 69616
> DMA zone: 4096 pages, LIFO batch:1
> Normal zone: 65520 pages, LIFO batch:15
> HighMem zone: 0 pages, LIFO batch:1
> DMI 2.2 present.
> Building zonelist for node : 0
> Kernel command line: ro root=/dev/hdc3 noapic single
> Initializing CPU#0
> PID hash table entries: 2048 (order 11: 16384 bytes)
> Detected 451.117 MHz processor.
> Console: colour VGA+ 80x25
> Memory: 271812k/278464k available (2117k kernel code, 5936k reserved,
> 753k data, 120k init, 0k highmem)
> Calibrating delay loop... 888.83 BogoMIPS
> Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
> Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> CPU: After generic identify, caps: 008021bf 808029bf 00000000 00000000
> CPU: After vendor identify, caps: 008021bf 808029bf 00000000 00000000
> CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
> CPU: L2 Cache: 256K (32 bytes/line)
> CPU: After all inits, caps: 008021bf 808029bf 00000000 00000002
> CPU: AMD-K6(tm) 3D+ Processor stepping 01
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfb480, last bus=1
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> PnPBIOS: Scanning system for PnP BIOS support...
> PnPBIOS: Found PnP BIOS installation structure at 0xc00fc0c0
> PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc0e8, dseg 0xf0000
> PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
> SCSI subsystem initialized
> drivers/usb/core/usb.c: registered new driver usbfs
> drivers/usb/core/usb.c: registered new driver hub
> PCI: Probing PCI hardware
> PCI: Probing PCI hardware (bus 00)
> PCI: Using IRQ router VIA [1106/0586] at 0000:00:07.0
> Machine check exception polling timer started.
> Installing knfsd (copyright (C) 1996 [email protected]).
> udf: registering filesystem
> SGI XFS for Linux with no debug enabled
> Activating ISA DMA hang workarounds.
> pty: 256 Unix98 ptys configured
> Linux agpgart interface v0.100 (c) Dave Jones
> Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> Using anticipatory io scheduler
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: IDE controller at PCI slot 0000:00:07.1
> VP_IDE: chipset revision 6
> VP_IDE: not 100% native mode: will probe irqs later
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci0000:00:07.1
> ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
> hda: ST320420A, ATA DISK drive
> hdb: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hdc: IBM-DTLA-305040, ATA DISK drive
> hdd: IC35L060AVVA07-0, ATA DISK drive
> ide1 at 0x170-0x177,0x376 on irq 15
> PDC20268: IDE controller at PCI slot 0000:00:09.0
> PCI: Found IRQ 10 for device 0000:00:09.0
> PDC20268: chipset revision 2
> PDC20268: ROM enabled at 0xe8000000
> PDC20268: 100% native mode on irq 10
> ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
> hde: WDC WD800JB-00ETA0, ATA DISK drive
> hdf: WDC WD800JB-00ETA0, ATA DISK drive
> hdf: set_drive_speed_status: status=0xff { Busy }
> ide2 at 0xd800-0xd807,0xdc02 on irq 10
> hda: max request size: 128KiB
> hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=39535/16/63
> hda: hda1 hda2
> hdc: max request size: 128KiB
> hdc: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=65535/16/63
> hdc: hdc1 hdc2 hdc3
> hdd: max request size: 128KiB
> hdd: 120103200 sectors (61492 MB) w/1863KiB Cache, CHS=65535/16/63
> hdd: hdd1
> hde: max request size: 1024KiB
> hde: status timeout: status=0xff { Busy }
>
> hde: drive not ready for command
> hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63
> hde: status timeout: status=0xff { Busy }
>
> hde: drive not ready for command
> hde:hde: status timeout: status=0xff { Busy }
>
> PDC202XX: Primary channel reset.
> hde: drive not ready for command
> ide2: reset timed-out, status=0xff
> hde: status timeout: status=0xff { Busy }
>
> PDC202XX: Primary channel reset.
> hde: drive not ready for command
> ide2: reset timed-out, status=0xff
> end_request: I/O error, dev hde, sector 0
> Buffer I/O error on device hde, logical block 0
> end_request: I/O error, dev hde, sector 0
> Buffer I/O error on device hde, logical block 0
> unable to read partition table
> hdf: max request size: 1024KiB
> hdf: status timeout: status=0xff { Busy }
>
> hdf: drive not ready for command
> hdf: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=16383/255/63
> hdf: status timeout: status=0xff { Busy }
>
> hdf: drive not ready for command
> hdf:hdf: status timeout: status=0xff { Busy }
>
> PDC202XX: Primary channel reset.
> hdf: drive not ready for command
> ide2: reset timed-out, status=0xff
> hdf: status timeout: status=0xff { Busy }
>
> PDC202XX: Primary channel reset.
> hdf: drive not ready for command
> ide2: reset timed-out, status=0xff
> end_request: I/O error, dev hdf, sector 0
> Buffer I/O error on device hdf, logical block 0
> end_request: I/O error, dev hdf, sector 0
> Buffer I/O error on device hdf, logical block 0
> unable to read partition table
> end_request: I/O error, dev hdb, sector 0
> hdb: ATAPI 24X CD-ROM CD-R/RW drive, 4096kB Cache
> Uniform CD-ROM driver Revision: 3.12
> drivers/usb/core/usb.c: registered new driver usblp
> drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
> drivers/usb/core/usb.c: registered new driver hid
> drivers/usb/input/hid-core.c: v2.0:USB HID core driver
> mice: PS/2 mouse device common for all mice
> input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> input: AT Translated Set 2 keyboard on isa0060/serio0
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25
> 19:16:36 2003 UTC).
> request_module: failed /sbin/modprobe -- snd-card-0. error = -16
> ALSA device list:
> No soundcards found.
> NET: Registered protocol family 2
> IP: routing cache hash table of 2048 buckets, 16Kbytes
> TCP: Hash tables configured (established 32768 bind 32768)
> NET: Registered protocol family 1
> UDF-fs DEBUG fs/udf/lowlevel.c:65:udf_get_last_session:
> CDROMMULTISESSION not supported: rc=-22
> UDF-fs DEBUG fs/udf/super.c:1544:udf_fill_super: Multi-session=0
> UDF-fs DEBUG fs/udf/super.c:531:udf_vrs: Starting at sector 16 (2048
> byte sectors)
> UDF-fs: No VRS found
> XFS mounting filesystem hdc3
> Ending clean XFS mount for filesystem: hdc3
> VFS: Mounted root (xfs filesystem) readonly.
> Freeing unused kernel memory: 120k freed
> Adding 512056k swap on /dev/hdc2. Priority:-1 extents:1
> md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
> XFS mounting filesystem hda1
> Ending clean XFS mount for filesystem: hda1
> XFS mounting filesystem hdd1
> Ending clean XFS mount for filesystem: hdd1
> XFS mounting filesystem hdc1
> Ending clean XFS mount for filesystem: hdc1
> XFS mounting filesystem hda2
> Ending clean XFS mount for filesystem: hda2
> hdb: DMA disabled
> hda: Speed warnings UDMA 3/4/5 is not functional.
> ide1: Speed warnings UDMA 3/4/5 is not functional.
> ide1: Speed warnings UDMA 3/4/5 is not functional.
> end_request: I/O error, dev hde, sector 0
> hde: set_drive_speed_status: status=0xff { Busy }
> end_request: I/O error, dev hde, sector 0
> hde: set_drive_speed_status: status=0xff { Busy }
> end_request: I/O error, dev hde, sector 0
> end_request: I/O error, dev hdf, sector 0
> hdf: set_drive_speed_status: status=0xff { Busy }
> end_request: I/O error, dev hdf, sector 0
> hdf: set_drive_speed_status: status=0xff { Busy }
> end_request: I/O error, dev hdf, sector 0